Oneil PrintPAD For 8100 Bedienungsanleitung
User's Guide
MICROFLASH 8I
TABLE OF CONTENTS
3
microFlash 8i Printer 4
Open View 4
Closed View 4
Installing a Radio Card 5
Using the Ribbon 6
Installing the Ribbon 6
Removing the Ribbon 7
Installing and/or Replacing Batteries 8
Charging the Battery 9
Loading Paper 10
Paper Quantity Guidelines 12
Tearing the Paper 12
Printing a Self-Test 12
Setting Top of Form (TOF) 13
Using Buttons and Indicators 14
Control Panel 14
LED Indicators 14
Button Functions 15
Audio Indicators 16
Using Power Options 17
Attaching Cables 18
Configuring the Printer 18
Supplies 20
MICROFLASH 8I PRINTER USER'S GUIDE
4
microFlash 8i Printer
Open View
Closed View
Battery
cavity
Battery
cable
Access
cover
Locking
lever (green
knob)
Control
panel
Printer
assembly
Figure 1
Paper Exit
Handle
Control
panel
Figure 2
MICROFLASH 8I PRINTER USER'S GUIDE
5
Installing a Radio Card
1. Open the printer’s cover.
2. Push in the locking tab and lift the access cover
(Figures 3 and 4).
3. Insert the radio card face up into the PCMCIA slot
(Figure 5).
4. Close the access cover and press down until the
locking tab clicks into place.
Note: The following information applies to printers
with radio card capabilities.
Figure 3 Figure 4
Figure 5
MICROFLASH 8I PRINTER USER'S GUIDE
6
Using the Ribbon
Installing the Ribbon
The printer ships without a ribbon installed. To install a
ribbon, perform the following:
1. Remove the ribbon from its packaging.
2. Open the printer’s cover.
3. Remove the orange “Open Printer” label from the
locking lever (green knob).
4. Depress the locking lever to open the print
mechanism.
5. Slide the printhead away from the edge of the
printer (Figure 6).
6. Hold the ribbon by the flat handle.
7. Install the ribbon on the printhead (Figure 7).
8. On the ribbon, turn the knob counter-clockwise
several times to fully seat the ribbon to the
printhead (Figure 8).
Figure 6 Figure 7
Figure 8
Knob
Printhead
MICROFLASH 8I PRINTER USER'S GUIDE
7
Removing the Ribbon
1. Slide the printhead away from the edge of the
printer (Figure 9).
2. Pull the ribbon away from the printer (Figure 10).
Figure 9
Figure 10
MICROFLASH 8I PRINTER USER'S GUIDE
8
Installing and/or Replacing Batteries
1. Open the printer’s cover. Verify the control panel is
facing toward you.
2. Place the battery in the battery cavity (Figure 11).
3. Connect the printer's cable connector to the battery
(Figures 12a and 12b). Verify the printer's battery
connector is aligned properly. The rubber key (on
the printer's battery connector) should be aligned
with the bottom notch (on the battery).
Figure 11
Figure 12a
Rubber
key
Figure 12b
MICROFLASH 8I PRINTER USER'S GUIDE
9
4. Install the battery strap over the printer's cable
connector and the battery so that they are both held
in place (Figure 13).
5. Close the printer’s cover.
6. Charge the battery. For more information, see
Charging the Battery on page 9
.
Charging the Battery
You can charge the battery either by connecting power
supplied from the AC power adapter, or by connecting
power supplied from the cigarette lighter adapter as
follows:
•AC Power Adapter: Plug the AC power cord into a
wall outlet. For information on using AC power, see
Using Power Options on page 17
.
•Cigarette Lighter Adapter: Connect the printer's
cigarette lighter adapter connector into your vehi-
cle's cigarette outlet. For more information, see
Using Power Options on page 17
.
The battery charges in approximately 4 to 5 hours.
Figure 13
MICROFLASH 8I PRINTER USER'S GUIDE
10
Loading Paper
1. Open the two latches on the side of the printer’s
cover and lift the printer’s cover to the fully open
position.
2. Depress the locking lever (green knob) to open the
print mechanism (Figure 14).
3. Verify the center guide is centered (Figure 15)
4. Lift the two tractor feed clips (Figure 16)
Note 1: Do not use paper that has glued edges or
paper with carbon between the sheets; only use paper
with clawed crimps.
Note 2: For information on the printer's paper capacity,
see
Paper Quantity Guidelines on page 12
.
Note: Remove the orange label from the locking lever
(green knob).
Figure 14
Figure 15
Center
guide
Figure 16
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere Oneil Drucker Handbücher
Oneil
Oneil VMP-2000 Bedienungsanleitung
Oneil
Oneil PrintPAD 9000 Bedienungsanleitung
Oneil
Oneil OC3 Bedienungsanleitung
Oneil
Oneil microFlash 8i 270 Bedienungsanleitung
Oneil
Oneil VMP-2000 Betriebsanleitung
Oneil
Oneil MF4T Bedienungsanleitung
Oneil
Oneil RP-1000 Betriebsanleitung
Oneil
Oneil microFlash 2t Bedienungsanleitung
Oneil
Oneil microFlash 8i Bedienungsanleitung
Oneil
Oneil microFlash 8i Bedienungsanleitung
Oneil
Oneil MICROFLASH 2TE Bedienungsanleitung
Oneil
Oneil microFlash 4t Bedienungsanleitung
Oneil
Oneil PrintPad 7900 Bedienungsanleitung
Oneil
Oneil LP3 Betriebsanleitung
Oneil
Oneil APEX 3 Bedienungsanleitung
Oneil
Oneil RP-2000 Bedienungsanleitung
Oneil
Oneil microFlash 2t Bedienungsanleitung
Oneil
Oneil VMP Series Bedienungsanleitung
Oneil
Oneil microFlash 4t Bedienungsanleitung
Oneil
Oneil MICROFLASH 2TE Bedienungsanleitung
