Onn 100006556 Bedienungsanleitung
The Fine Print
Additional Warnings and Precautions
• CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO
WIDE SLOT, FULLY INSERT.
• Mains plug is used as disconnect device and it should remain readily operable
during intended use. In order to disconnect the apparatus from the mains
completely, the mains plug should be disconnected from the mains socket outlet
completely.
• CAUTION: Use of controls or adjustments or performance of procedures other
than those specified may result in hazardous radiation exposure.
• WARNING: Changes or modifications to this unit not expressly approved by the
party responsible for compliance could void the user’s authority to operate the
equipment.
• WARNING: Use of this unit near fluorescent lighting may cause interference
regarding use of the remote. If the unit is displaying erratic behavior move away
from any fluorescent lighting, as it may be the cause.
• WARNING: Shock hazard - Do Not Open.
• Caution and marking information is located at the rear or bottom of the
apparatus.
• WARNING: To reduce the risk of fire or electric shock, do not expose this
apparatus to rain, moisture, dripping, or splashing.
• Objects filled with liquids, such as vases, shall not be placed on the apparatus.
Copyright © 2019 Digital Products International (DPI, Inc.) All other trademarks
appearing herein are the property of their respective owners. Specifications are
subject to change without notice.
FCC Warnings
Warning: Changes or modifications to this unit not expressly approved by the party
responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined
by turning the equipment o and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent from that to which
the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
[Product barcode
goes here.]
We’d love to hear from you. Scan
with your Walmart app and let us
know what you think.
3 Speed Turntable
Quick Start Guide
What’s in the Box? Get to Know Your Turntable
Product
Guide
TM
13
2
4
1. Turntable
2. Turntable Platter Mat
3. RCA Stereo Audio Cable
4. Product Quick Start Guide
Check to make sure you
have everything below.
5
6
7
9
8
10
11
1. 45rpm Adapter
2. Platter
3. Tone Arm Lock
4. Pitch Adjustment
5. Tone Arm Counterweight
6. Anti-Skating Adjustment
7. Tone Arm Lift Switch
8. Tone Arm
9. Bluetooth Pair Button
10. Power ON/OFF/Speed
11. Power/Bluetooth
Indicator
2
1
3
4
Top
Let’s Get Started! Load a Record
Here’s what you’ll need to do
to start playing: 01
• Place your record on the platter.
• Set the speed selector dial to match your
record type - 33, 78, or 45. If you are playing a
45rpm record, be sure to use the adapter.
• Remove the protective cover on the stylus, then
release the lock on the tone arm.
• Use the tone arm lift switch to raise the tone
arm upwards, then carefully move it into position
over the record.
• As the tone arm moves into position, the platter
will start spinning. Use the tone arm lift switch to
lower the tone arm stylus onto the record. When
the stylus comes into contact with the grooves
on the record, the turntable will send audio to
the connected speakers.
1. Plug in the AC power cord.
2. Balance the tone arm counterweight.
3. Assemble the platter to the deck, looping the
drive belt around the motor spindle.
2
1
3
Connecting to External SpeakersConnecting to a Bluetooth Speaker 03
02
• Enable Pairing Mode on your Bluetooth Speaker.
Before beginning the pairing process, be sure no
other devices are connected to the speaker.
• On the turntable, turn Bluetooth Mode ON by
adjusting the switch on the back of the unit.
• Press the Pair button on the turntable to begin
pairing to your speaker. The indicator light
on the turntable will quickly flash blue while it
attempts to connect to the speaker.
• When successfully paired, the indicator light on
the turntable will turn solid. Note: If the turntable
fails to connect, the indicator light will keep
flashing blue. Press the Pair button to try again.
• Use an RCA audio cable to connect to a pair of
external speakers. Connect the Line Out ports
on the turntable to the corresponding color-
coded ports on the speakers.
• Set the selector switch on the back of the
turntable to Line Out to send audio to the
speakers.
Andere Handbücher für 100006556
1
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere Onn Drehscheibe Handbücher
