Oracle SPARC Enterprise M3000 Bedienungsanleitung

This guide describes the minimum steps you must perform to power on and boot your server for the first time.

Before installing the SPARC Enterprise M3000 server, check for late-breaking information about patches and

known issues. Information found in the

SPARC Enterprise M3000/M4000/M5000/M8000/M9000 Servers

Product Notes

supersedes the information in this document.

Detailed installation information can be found in the

SPARC Enterprise M3000 Server

Installation Guide, which is

available at the documentation web site:

http://www.oracle.com/technetwork/documentation/sparc-mseries-servers-252709.html

Safety and Compliance Information

Before performing an installation, refer to the following documents for safety information regarding the SPARC

Enterprise M3000 Server:

■Important Legal and Safety Information – Printed document included in the ship kit.

■SPARC Enterprise M3000 Server Safety and Compliance Manual – Available online at the documentation web

site.

Prepare the Site for Installation

1. Verify power, air conditioning, and floor area requirements.

See the SPARC Enterprise M3000 Server Site Planning Guide.

2. Check the delivered items against the “LIST OF ATTACHMENT” that came with the server.

1. Locate the serial number for your system or the customer information sheet that came with the system.

2. Go to the following web site to register your system:

http://www.sun.com/service/warranty/index.xml#reg

SPARC Enterprise M3000 Server

Getting Started Guide

Install Optional Components

Before installing the server into the rack, you must first install any optional components that you ordered with

the server, such as DIMMs, PCIe cards, and so on. Refer to the SPARC Enterprise M3000 Server Service Manual for

the instructions on installing optional components.

Mount the System In a Rack

For rackmounting instructions, refer to the instructions in the SPARC Enterprise Rack Mounting Guide (online)

and the Rail Kit Instructions which ships with the rails.

Installation Steps for the SPARC Enterprise M3000 Server

For quick installation and configuration, follow these steps. For more detailed information, see the SPARC

Enterprise M3000 Server Installation Guide.

Caution – Make sure that the AC power source circuit breaker is in the OFF position before

connecting the AC power cords.

▼Connect the Cables

1. Connect the power cords to the power supply units on the rear panel of the server.

2. Connect the power cords to the AC power supply system.

This server is shipped with grounding-type (three-wire) power cords. Always connect the power cords into

grounded power outlets.

FIGURE 1 Rear Panel of the Server

Figure Legend

Location Number Component

1 Power supply unit

2 PCIe slot

3 Serial port (for XSCF)

4 LAN port (for XSCF)

5 Gigabit Ethernet (GbE) port (for OS)

1 2 34

3. Use the RS232C cable (serial cable, RJ-45 to DB-9) supplied with the server in the Accessory Kit, and

connect the administration console to the serial port (see FIGURE 1, #3) on the rear panel of the server.

You can use any of the following devices with a DB-9 serial port as the administration console: ASCII

terminal, workstation, terminal server (or a patch panel connected to a terminal server), or personal

computer. A Serial-to-USB port adapter may be required for laptops.

▼Initialize the XSCF

The following steps will log in to the XSCF Shell and initialize the XSCF settings. XSCF is a system control

facility to set up and control the server.

1. Set the mode switch on the operator panel to the Service mode ( ).

The key for the operator panel is supplied with the server.

FIGURE 2 Operator Panel

2. Turn the AC power source circuit breaker to "ON".

After AC power is turned on, the server starts the XSCF initialization that can take up to 5 or more minutes.

When the initialization completes, the XSCF STANDBY LED ( ) on the operator panel lights.

3. After the XSCF initialization completes, enter default at the login prompt.

Figure Legend

Location No. Name

1 POWER LED

2 XSCF STANDBY LED

3 CHECK LED

4 Power button

5 Mode switch (Key switch)

4. Operate the mode switch within one minute according to the messages to change the mode switch.

A login authentication timeout will occur after one minute.

5. Confirm that the XSCF Shell prompt is displayed on the administration console.

6. Initialize the XSCF settings. The following are the required settings for installation.

For details on the setting procedure, see the SPARC Enterprise M3000/M4000/M5000/M8000/M9000 Servers

XSCF User’s Guide.

7. Log in to the XSCF Shell with the user account and password that were set in Step 6.

▼Power On the Server

1. The following steps will power on the server.

a. Confirm that the mode switch on the operator panel is set to the Service mode ( ).

b. From the XSCF Shell, enter the following console command:

This switches you from the XSCF Shell to the domain console.

c. Confirm that the XSCF STANDBY LED ( ) on the operator panel is on.

Change the panel mode switch to Locked and press return...

Leave it in that position for at least 5 seconds.

Change the panel mode switch to Service, and press return...

XSCF>

Settings Command

Registration of an XSCF user account, password, and user privileges

Registration of a user account of a field engineer (FE) (for maintenance)

adduser,password,

setprivileges

Date and time settings setdate,settimezone

Confirmation of the XSCF host public key showssh

SSH/telnet settings setssh,settelnet

Network interface, routing, and DNS-related settings*

* To apply the settings, the XSCF unit must be reset with the applynetwork and rebootxscf commands.

setnetwork,setroute,

setnameserver etc.

Domain-SP Communication Protocol (DSCP) settings†

† To apply the settings, the XSCF unit must be reset with the rebootxscf commands.

Altitude administration setting‡

‡ To apply changes made with the setdualpowerfeed command, power to the server must be completely disconnected and then

reconnected (all power cords must be disconnected and then reconnected). Wait at least 30 seconds before reconnecting the power cords to

the server.

setaltitude

Dual power feed option setting setdualpowerfeed

XSCF> console -d 0

Connect to DomainID 0?[y|n] :y

d. Push the Power button ( ) on the operator panel to power on the server.

The server starts and begins a self-diagnosis. Confirm that no error messages are displayed on the

administration console during the boot process.

e. Confirm that the POWER LED ( ) on the operator panel is turned on.

f. Confirm that ok prompt is displayed on the domain console.

The ok prompt is displayed after the self-diagnosis completes.

g. Press the Enter key, and then press the "#" and “.”(period) keys.

This switches you from the domain console to the XSCF Shell.

h. From the XSCF Shell, execute the fmdump command or showlogs command, and confirm that no

errors are found.

2. Connect the system control network to a LAN port (see FIGURE 1, #4) on the rear panel of the server with

an Ethernet cable.

3. Verify the hardware configuration by using the following commands on the administration console

connected to the system control network.

To switch from the XSCF console to the ok prompt, enter the console -d 0 command. To switch from the

ok prompt to the XSCF console, press the enter key, and then press the "#" and "." (period) keys.

4. Install additional hardware or peripheral devices. If not needed, proceed to the Step 5.

For details on how to add optional devices, such as additional memory or an additional PCIe card, see the

SPARC Enterprise M3000 Server Service Manual. To add an additional storage device or other peripheral

device, see the manual supplied with the device.

5. The following steps will connect the domain to the user network. If you isolate the domain from the

network, proceed to the Step 1.

The user network is a network which enables users to access the domain.

a. Connect one end of an Ethernet cable to a GbE port (for the OS) (see FIGURE 1, #5) on the rear panel of

the server.

You can connect the Ethernet cable to a GbE port (for the OS) or to the LAN port on a LAN card mounted

in a PCIe slot (see FIGURE 1, #2).

b. Connect the other end of the Ethernet cable to the customer’s network environment.

▼Boot the Oracle Solaris Operating System

1. The following steps will boot the Oracle Solaris Operating System.

The Oracle Solaris OS is preinstalled in the slot 0 of the hard disk drives.

Command Prompt Description

showhardconf XSCF Shell All the components installed in the server and their statuses are displayed.

Confirm that no asterisk (*) is displayed in front of any FRUs.

showhardconf -u XSCF Shell Check the number of FRUs mounted on the server against the “PRODUCT

TEST RECORD“ that came with the server.

probe-scsi-all ok Prompt Confirm that the CD-RW/DVD-RW drive unit and hard disk drive

installed in the server are recognized.

show-devs ok Prompt Confirm that each installed PCIe card is recognized.

Part No.: 821-3055-11

Manual Code: C120-E549-04EN

February 2011

a. From the ok prompt of the domain console, execute the boot command.

b. After the login prompt is displayed, log in with root account.

2. Confirm the status of hardware operations and device connection by using the Oracle VTS software.

For details, see the Oracle VTS user’s guide.

3. Make the initial settings for the domain.

For details, see the SPARC Enterprise M3000/M4000/M5000/M8000/M9000 Servers Administration Guide.

SPARC Enterprise M3000 Server Related Documentation

Contact Information

ok boot

System Planning and Site Preparation • SPARC Enterprise M3000 Server Overview Guide

• SPARC Enterprise M3000 Server Site Planning Guide

System Installation • SPARC Enterprise Equipment Rack Mounting Guide

• SPARC Enterprise M3000 Server Installation Guide

Administration • SPARC Enterprise M3000/M4000/M5000/M8000/M9000 Servers Product

Notes

• SPARC Enterprise M3000/M4000/M5000/M8000/M9000 Servers

Administration Guide

• SPARC Enterprise M3000/M4000/M5000/M8000/M9000 Servers XSCF

User’s Guide

• SPARC Enterprise M3000/M4000/M5000/M8000/M9000 Servers XSCF

Reference Manual

Repair and

Troubleshooting

• SPARC Enterprise M3000 Server Service Manual

Topic URL

Technical support http://support.oracle.com

Patch and firmware updates http://support.oracle.com

Andere Handbücher für SPARC Enterprise M3000

Inhaltsverzeichnis

Andere Oracle Server Handbücher

Oracle

Oracle SPARC T5-8 Bedienungsanleitung

Oracle

Oracle SPARC T8-4 Bedienungsanleitung

Oracle

Oracle Sun SPARC T3-2 Bedienungsanleitung

Oracle

Oracle Exalytics In-Memory Machine Bedienungsanleitung

Oracle

Oracle SUN X4-8 Bedienungsanleitung

Oracle

Oracle EXADATA X5-8 Bedienungsanleitung

Oracle

Oracle Sun Fire X4470 Service-Handbuch

Oracle

Oracle EXADATA X6-2 Bedienungsanleitung

Oracle

Oracle X6 series Bedienungsanleitung

Oracle

Oracle Sun Netra FT 1800 Technisches Handbuch

Oracle

Oracle EXADATA X6-2 Bedienungsanleitung

Oracle

Oracle Sun Fire X4470M2 Service-Handbuch

Oracle

Oracle netra X5-2 Bedienungsanleitung

Oracle

Oracle Video server Bedienungsanleitung

Oracle

Oracle T5140 Bedienungsanleitung

Oracle

Oracle X4-2B Bedienungsanleitung

Oracle

Oracle SPARC T5-2 Bedienungsanleitung

Oracle

Oracle SUN X4-8 Bedienungsanleitung

Oracle

Oracle SPARC T7-2 Bedienungsanleitung

Oracle

Oracle Sun Server X2-4 Bedienungsanleitung

Oracle

Oracle netra X5-2 Bedienungsanleitung

Oracle

Oracle JFNA2-7 Installations- und Betriebsanleitung

Oracle

Oracle Sun Server X4-4 Bedienungsanleitung

Oracle

Oracle Sun Fire X4170 M2 Service-Handbuch

Beliebte Server Handbücher anderer Marken

HP AlphaServer ES47 Bedienungsanleitung

Dell

Dell PowerEdge R410 Bedienungsanleitung

PowerNAS

PowerNAS CMA Bedienungsanleitung

Supero

Supero FatTwin F617R3-FT Bedienungsanleitung

MSI

MSI P1-109N-L70 Bedienungsanleitung

Dell

Dell PowerEdge XE9640 Handbuch

Dell

Dell PS4100 Montageanleitung

EtroVISION

EtroVISION EV3151 Bedienungsanleitung

NEC

NEC Express5800/T110j Bedienungsanleitung

HP ProLiant Gen9 Bedienungsanleitung

Compaq

Compaq ProLiant 3000 Handbuch

Dell

Dell PowerEdge 3YPMN Bedienungsanleitung

iRobo

iRobo IPC2U Bedienungsanleitung

Nortel

Nortel 1000 Con?guration guide Bedienungsanleitung

Asus

Asus AP7500 Bedienungs- und Wartungshandbuch

Avid Technology

Avid Technology AirSpeed 5000 Bedienungsanleitung

HP Integrity rx2600 Installationsanleitung

Milestone

Milestone Husky IVO 350T Bedienungsanleitung