Oregon Scientific RM813 Bedienungsanleitung

Radio Controlled

KidsProjectionClock

withNightlight

MODEL:RM813PA

Instruction Manual

INTRODUCTION

Congratulations on your purchase of the RF Projection Clock

RM813PA.

The RM813PA is a multifunctional radio-controlled clock. It can

automatically synchronize its current time and date when brought

within range of the U.S. Atomic Clock.

The unit comes with a projector that in the dark can project large,

clear clock-time digits onto the flat surfaces. It also has a nightlight

at the back of the unit.

MAIN FEATURES

A Two-line display

Displays the current time and calendar or alarm time

B[ ] Radio reception signal

Indicates the condition of radio reception

C[ ] Alarm icon

Appears when alarm is activated

D[ ] Alarm icon

Appears when alarm time is displayed

SNOOZE ] button

Enablesthesnoozefunctionwhenthealarmgoesofforactivates

the projector for five seconds

F Up[ ]button

Increases or decreases the value of a setting

ZONE ]button

Press to toggle among the 4 U.S. time-zones: Pacific (P),

Mountain (M), Central (C) or Eastern (E)

H[ ON/OFF ] button

Press to turn on or off the alarm

I[ ] button

Sets the time for the alarm

MODE ] button

Toggles the display modes and confirms entry in clock setting

mode

K Projector

For projecting the current time on the wall or ceiling

L[ PROJECTION ON ] switch

Used with the power adapter to enable extended use of the

projector

LIGHT ON ] switch

Used with power adapter to enable extended use of the guiding

light

TEST ] button

Turn on the nightlight as long as it is pressed and held

RESET ] button

Resets the unit by returning all settings to factory default

values

P Batterycompartment

Accommodates two (2) UM-3 or “AA” size batteries

Q Night light

R ACadapterjack

BATTERY INSTALLATION

The unit uses two (2) UM-3 or “AA” size 1.5V batteries.

To insert batteries:

1. Slide the battery door in the direction of the arrow.

2. Insert the batteries according to the polarities shown therein.

3. Replace the battery compartment door.

4. Press the [RESET] button.

When the low battery indicator [ ] is shown on the display,

replace with fresh batteries.

Note: Under normal circumstances, the batteries are good for 1

year. However, the battery life can be reduced vastly by frequent

use of the projector or snooze function.

If not disposed of properly batteries can be harmful.

Protect the environment by taking exhausted batteries

to authorized disposal stations.

MOMENTARY PROJECTION FEATURE

Press [ SNOOZE ] and the projection will be activated for

approximately 5 seconds.

Note: Make sure the [ PROJECTION ON ] switch is switched to the

front i.e. it is in the “Off” position.

CONTINUOUS PROJECTION FEATURE

WITH POWER ADAPTER

RM813PA comes with an AC power adapter. Use of the AC power

adapter is required for continuous time projection.

To install the adapter:

1. Insert adapter into the jack at the bottom of the unit.

2. Plug the adapter into an electrical wall outlet.

Note: Make sure the voltage is correct.

Once the power adapter is in place, you can select to turn on the

projector for longer time (such as throughout the night) by sliding

the [ PROJECTION ON ] switch (located on the side of the unit) to

thebacki.e.itisinthe“On”position.Toturnofftheprojector,slide

the switch to the front to the “Off” position.

Note that this switch can only be used with the power

adapter. For momentary projection, use the [ SNOOZE ].

ABOUT RADIO RECEPTION

RM813PA is designed to synchronize its calendar clock

automatically once it is brought within range of the U.S. Atomic

Clock.When theunitis newandjust outofthe box,synchronization

with the U.S. atomic clock can take up to 72 hours. The unit will

receive the most dependable and interference free signal

automatically between Midnight and 4 AM.

When the unit is receiving signal, the Radio Reception symbol

[] will start to blink. Generally, complete reception takes

around 2 to 10 minutes depending on the strength of the radio

signal.

To disable the reception of RF signal manually, press and hold the

[ ZONE ] button for 3 seconds until the Radio Reception symbol

and the US-map outline disappear.

To enable the reception again, press and hold the [ ] button for

3 seconds. The Radio Reception symbol and the US-map outline

will blink and the unit will search for RF signal automatically.

STRONG

WEAK

NORECEPTION

RECEIVING

Interference

Receptioncanbeaffectedbyanumberoffactors.Forbestreception,

place the device away from metal objects and electrical appliances.

Other causes for signal interference include electrical power

transmission towers, steel reinforced concrete construction, and/

or metal siding.

When the icon [ ]. appears on the display, re-locate the unit to

enhance better reception of radio signal.

Note: Radio Frequency appliances such as the Projection Alarm

Clock perform best when placed near a window. After receiving the

initial signal, updates are accomplished with greater ease. Even

though there are areas that may have more difficulty in receiving

a signal, the Projection Alarm Clock contains very accurate quartz

movement and will retain precise time even if a signal is missed on

a rare occasion.

HOW TO SET THE CLOCK AND

CALENDAR MANUALLY

To set the clock and calendar:

1. Press and hold [MODE] for 2 seconds and the hour digits will

flash.

2. Enter the value by [ ] button.

3. Confirm the entry by pressing [MODE] and the minutes digits

will flash.

4. Repeat (2) and confirm the entry by pressing [MODE].

5. Repeat the above steps to set the year, month, day and language

for day-of-week. For the day of the week language you can

select among English (E), French (F) or Spanish (S).

Day-of-the-week

Language Monday Tuesday Wed. Thursday Friday Saturday Sunday

English

French

Spanish

To toggle among the 4 U.S. time-zones, press [ZONE] button to

display Pacific, Mountain, Central or Eastern.

HOW TO SET THE ALARM

This unit is equipped with a daily alarm.

To set and activate the alarm:

1. Display the alarm time by pressing [] .

2. Press and hold [] for 2 seconds. The hours digits will flash.

3. Enter the values by [ ] buttons.

4. Confirm the entry by pressing [] .

5. The minutes digits will flash.

6. Repeat (3) and (4) to finish the setting. The alarm will be

activated automatically.

To deactivate the alarm:

1. Press [ ON/OFF ] to deactivate the Alarm. [ ] will

disappear when the alarm is being deactivated.

2. Press [ ON/OFF ] to activate the alarm again.

CRESCENDO ALARM AND

SNOOZE FUNCTION

When the alarm goes off at the preset time, the projection will be

turned on for 8 seconds. The [ ] icon will be flashing and the

alarm sound will be turned on.

The crescendo alarm function allows the alarm sound to start off

gently with step-up intensity. Without interruption, the alarm will

be on for 2 minutes.

To stop the alarm, press [], [ ON/OFF ] or [SNOOZE]. If

[ ON/OFF]is pressed, the alarm will be turned off permanently.

If [] is pressed, the alarm will be turned off and be activated

again after 24-hours. If [SNOOZE] button is pressed, the alarm

sound will be turned off temporarily and the snooze function will

be activated. The alarm will go off again after approx. 8 minutes

until other key is pressed to turn off the alarm.

RESETTING THE UNIT

In case of malfunction or abnormal display, press the [RESET]

button at the bottom of the unit wth a blunt stylus. All settings will

be cleared and reset to their default values.

HOW TO USE THE NIGHTLIGHT

RM813PA is equipped with a nightlight. To turn on the nightlight

temporarily for testing its functionality, press the [TEST] button

with a blunt stylus at the bottom of the unit. The light will be on

as long as the button is pressed and held.

For continuous use of the nightlight, AC Power adapter is required

to be connected. For instructions on how to install the adapter,

please see Section “Continuous Projection feature with Power

Adaptor.”

Oncethepoweradapterisinplace,slidethe [LIGHTON ]switch

(located at the side of the unit) to the back i.e. the “On” position.

The nightlight will be turned on for a longer time. To turn the light

off, simply slide the switch in the opposite direction.

Note that this switch can only be used when the power adapter is

installed. For turning the light on momentarily, use the [TEST]

instead.

HOW TO CHANGE

THE GUIDING LIGHT BULB

RM813PA is pre-installed with a 3V lightbulb. In case you want to

change the lightbulb follow the instructions below:

1. Un-install the power adapter from the unit to prevent electric

shock. Also,removethebatteriesfromthebatterycompartment.

2. Remove the tail of the unit as shown.

3. Then, remove the lightbulb by rotating it in a anti-clockwise

direction.

4. Replace with new light bulb with correct specifications. Make

sure the light bulb is securely fixed.

5. Replace the tail of the unit as shown.

6. To test if the guiding light is working properly, install batteries

into the battery compartment and press the [TEST] button. The

light should be turned on as long as the button is held.

7. If the light does not turn on, check if the lightbulb is broken or

if the lightbulb is well-connected to the unit.

MAINTENANCE

When handled properly, this unit is engineered to give you years

of satisfactory service. Here are a few product care instructions:

1. Do not immerse the unit in water. If the unit comes in contact

with water, dry it immediately with a soft lint-free cloth.

2. Do not clean the unit with abrasive or corrosive materials.

Abrasive cleaning agents may scratch the plastic parts and

corrode the electronic circuit.

3. Do not subject the unit to excessive: force, shock, dust,

temperature, or humidity. Such treatment may result in

malfunction, a shorter electronic life span, damaged batteries,

or distorted parts.

4. Do not tamper with the unit’s internal components. Doing so

will terminate the unit’s warranty and may cause damage. The

unit contains no user-serviceable parts.

5. Only use new batteries as specified in this instruction manual.

6. Read this instruction manual thoroughly before operating the

unit.

PRODUCT SPECIFICATIONS

Operating Temperature : +23°F to +122°F (-5°C to 50°C)

Radio Controlled : Auto synchronizes current time and

date by Radio signal generated from

the U.S. Atomic Clock

Calendar : Day of week in English / French /

Spanish

Current month / day format

Clock Time : 12-hour format

Accuracy : +/- 0.5 second/day

(when RF is disabled)

Battery Type : Two(2)UM-3or“AA”size1.5Vbatteries

Unit Dimension : 3.54 x4.37 x5.83inches ( H x W x D )

Unit Weight : 7.05ounces (without battery)

Lightbulb Rating : 3V, 300mA

Lightbulb Dimension : T10 x 1.10inches

CAUTION

— The content of this manual is subject to change without

further notice.

— Due to printing limitation, the displays shown in this

manual may differ from the actual display.

— The contents of this manual may not be reproduced

without the permission of the manufacturer.

CUSTOMER ASSISTANCE

Should you require assistance regarding this product and its

operation, please contact our customer care department at

800-853-8883 or via email at [email protected].

WARRANTY

This product is warranted to be free of manufacturing defects for a

period of 90 days from date of retail purchase. Defective product

should be directed to the place of retail purchase for exchange.

Should this not be possible, contact our customer care department

for assistance and a return material authorization. No returns may

be made without a return authorization. Please retain your retail

receipt as you may be asked to provide a copy of it for proof of date

purchased.

This warranty does not cover product subjected to abuse, misuse,

accidental damage or tampering.

Inhaltsverzeichnis

Andere Oregon Scientific Uhr Handbücher

Oregon Scientific

Oregon Scientific RRA320PN Bedienungsanleitung

Oregon Scientific

Oregon Scientific JM889 Bedienungsanleitung

Oregon Scientific

Oregon Scientific DP200 Bedienungsanleitung

Oregon Scientific

Oregon Scientific RM901A Bedienungsanleitung

Oregon Scientific

Oregon Scientific RRA320PNX Bedienungsanleitung

Oregon Scientific

Oregon Scientific BAR669H Bedienungsanleitung

Oregon Scientific

Oregon Scientific RMR682 Bedienungsanleitung

Oregon Scientific

Oregon Scientific RMR802 Bedienungsanleitung

Oregon Scientific

Oregon Scientific JM889NR Bedienungsanleitung

Oregon Scientific

Oregon Scientific RMB899P Bedienungsanleitung

Oregon Scientific

Oregon Scientific RM328P Bedienungsanleitung

Oregon Scientific

Oregon Scientific RM313PU Bedienungsanleitung

Oregon Scientific

Oregon Scientific RM329P Bedienungsanleitung

Oregon Scientific

Oregon Scientific TW221 Bedienungsanleitung

Oregon Scientific

Oregon Scientific Silverstone FAP-101 Bedienungsanleitung

Oregon Scientific

Oregon Scientific RM313PNA Bedienungsanleitung

Oregon Scientific

Oregon Scientific RM962A Bedienungsanleitung

Oregon Scientific

Oregon Scientific RMR331ES Bedienungsanleitung

Oregon Scientific

Oregon Scientific KD500 Bedienungsanleitung

Oregon Scientific

Oregon Scientific RM998PS Bedienungsanleitung

Oregon Scientific

Oregon Scientific POLERMO RMR939PA Bedienungsanleitung

Oregon Scientific

Oregon Scientific RM318PU Bedienungsanleitung

Oregon Scientific

Oregon Scientific POLERMO RMR939PA Bedienungsanleitung

Oregon Scientific

Oregon Scientific RM802 Bedienungsanleitung

Beliebte Uhr Handbücher anderer Marken

Silicon Laboratories

Silicon Laboratories SI5324 Bedienungsanleitung

Heathkit

Heathkit GC-1005 Bedienungsanleitung

Andrew O'Malley

Andrew O'Malley DOTKLOK Bedienungsanleitung

ALGE-Timing

ALGE-Timing ASC3 Bedienungsanleitung

Bodet

Bodet Profil 960 Bedienungsanleitung

Nixie Clock

Nixie Clock Divergence Meter Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-8256-AL Bedienungsanleitung

Mini Gadgets

Mini Gadgets MCPro Bedienungsanleitung

Casio

Casio TMR-200 Bedienungsanleitung

Progetti

Progetti ILTEMPOSTRINGE Handbuch

BVItech

BVItech BV-101 Bedienungsanleitung

Progetti

Progetti KALIMERO Handbuch

La Crosse Technology

La Crosse Technology WT-3141b Handbuch

La Crosse Technology

La Crosse Technology W86531 Bedienungsanleitung

Sharp

Sharp SPC900 Bedienungsanleitung

La Crosse Technology

La Crosse Technology 404-50447 Bedienungsanleitung

Datexx

Datexx DF0063 Bedienungsanleitung

LG LEC-005 Bedienungsanleitung