Oregon Scientific RMR182 Bedienungsanleitung

Multi-Channel In-Out Thermometer

with Cable Free Sensor and RF Clock

MODEL: RMR182

USER'S MANUAL

INTRODUCTION

Congratulations on your purchase of the RMR182 Multi-

Channel In-Out Thermometer with 433MHz cable free sensor and

radio-controlled calendar clock.

The basic package comes with a main unit, which is the tempera-

ture and calendar clock station, and a remote unit, the thermo

sensor.

The main unit has a large display for indoor temperature,

calendar clock and temperatures collected and transmitted by the

remote unit. The main unit can support up to three remote units.

The main unit is capable of keeping track of the maximum and

minimum temperature of different sites. No wire installation is

required as the RMR182 operates at 433MHz.

As for the calendar clock, it is radio-controlled. It automatically

synchronizes its current time and date when it is brought within

an approximate 1500km radius of the radio signal generated from

Frankfurt,Germany(DCF77).

You can also set the calendar clock manually when it is off range.

Other features include four-language display, four-step crescendo

dual alarms and interchangeable display modes.

MAIN FEATURES: MAIN UNIT

A FOUR-LINE LCD DISPLAY

Facilitates easy reading of remote and indoor temperatures

and calendar clock

B[ ]RADIO-RECEPTION SIGNAL

Indicates the condition of radio reception

C TEMPERATURETREND INDICATOR

Indicates the trend of temperature changes

D [ ]BATTERY-LOW INDICATOR

(REMOTE SENSOR)

Activates when the remote-sensor battery is low

E [ ]BATTERY-LOW INDICATOR

Activates when the battery is low

F[ ]/[ ]ALARM-ON ICONS

Appears when the alarm is activated

G[(

(1))]/[((2))]ALARM ICONS

Appears when the alarm time is displayed

H [SET/MODE]BUTTON

Toggles between display modes and confirms entry while

setting the values for display

I[((.))]BUTTON

Displays and sets alarm time

J [MEMORY]BUTTON

Displays maximum / minimum temperature

K [CHANNEL]BUTTON

Selects remote-sensor channels

]BUTTON

Advances the value of a setting

M[ ]BUTTON

Decreases the value of a setting

N [ALON/OFF]BUTTON

Enables or disables the alarms

O [RESET]BUTTON

Returns all settings to default values

P °C/°F SLIDE SWITCH

Selects between degree Centigrade (°C) and Fahrenheit (°F)

Q BATTERY COMPARTMENT

Accommodates two (2) UM-3 or “AA” size batteries

R REMOVABLETABLE STAND

For standing the main unit on a flat surface

S WALL-MOUNT HOLE

For mounting the main unit on a wall

MAIN FEATURES: REMOTE UNIT A LCD DISPLAY

Displays the current temperature monitored by the remote

unit

B LED INDICATOR

Flashes when the remote unit transmits a reading

C °C/°F SLIDE SWITCH

Selects between Centigrade (°C) and Fahrenheit (°F)

D CHANNEL SLIDE SWITCH

Designates the remote unit Channel 1, Channel 2 or

Channel 3

E RESET BUTTON

Returns all settings to default values

F BATTERYCOMPARTMENT

Accommodates two UM-4 or “AAA” size batteries

G BATTERY DOOR

H WALL-MOUNTHOLDER

Supports the remote unit in wall-mounting

I REMOVABLETABLE STAND

For standing the remote unit on a flat surface

BEFORE YOU BEGIN

For best operation,

1. Assign different channels to different remote units.

2. Insert batteries for remote units before doing so for the main

unit.

4. Install 2 alkaline batteries (UM-4 or “AAA” size 1.5V) strictly

according to the polarities shown.

5. Replace the battery compartment door and secure its screws.

Note that once a channel is assigned to a remote unit, you can only

change it by removing the batteries or resetting the unit.

BATTERY INSTALLATION: MAIN UNIT

1. Gently lift the tab on the battery compartment door.

2. Install 2 alkaline batteries (UM-3 or “AA” size 1.5V) strictly

according to the polarities shown.

3. Replace the battery compartment door.

3. Place the main unit as close as possible next to the remote unit

and reset the main unit after installing batteries. This will

ensure easier synchronization between the transmission and

reception of signals.

4. Position the remote unit and main unit within effective trans-

mission range, which, in usual circumstances, is 20 to 30

meters.

Note that the effective range is vastly affected by the building

materials and where the main and remote units are positioned.Try

various set-ups for best result.

Though the remote units are weather proof, they should be placed

away from direct sunlight, rain or snow.

BATTERY AND CHANNEL

INSTALLATION: REMOTE UNIT

1. Remove the screws on the battery compartment.

2. Select the channel number on the CHANNEL slide switch.

3. Select the temperature display unit on the °C/°F slide switch.

Remoteunit

Wall-mount Table Stand

THE RESET BUTTON

This button is only used when the unit is operating in an unfavor-

able way or malfunctioning. Use a blunt stylus to hold down the

button. All settings will return to their default values.

GETTING STARTED

Once batteries are in place for the remote units, they will start

transmitting temperature readings at 30-second intervals.

The main unit will also start searching for signals for about a

minute once batteries are installed. Upon successful reception,

the individual channel temperatures will be displayed on the top

line and the indoor temperature on the second line. The main unit

will automatically update its readings at about 30-second inter-

vals.

LOW BATTERY WARNING

When it is time to replace batteries, the low-battery indicator will

show up when the corresponding channel is selected. The battery

level of the main unit will be shown on the indoor temperature

when it is running low.

HOW TO USE THE TABLE STAND

OR WALL MOUNTING

The main unit has a removable table stand, which when installed,

can support the unit on a flat surface. Or you can remove the stand

and mount the unit on a wall using the recessed screw hole.

As for the remote unit, it comes with a wall-mount holder and a

removable stand. Use either to hold the unit in place.

Mainunit

Wall-mount Table Stand

If no signals are received, blanks "----" will be displayed and the

kinetic wave icon will show " ". Press [CHANNEL] and

[MEMORY] simultaneously to enforce another search for about

30 seconds. This is useful in synchronizing the transmission and

reception of the remote and main units.

Repeat this step whenever you find discrepancies between the

reading shown on the main unit and that on the corresponding

remote unit.

HOW TO CHECK REMOTE AND

INDOOR TEMPERATURES

The indoor temperature is shown on the second line of the display.

As for the remote sites or channels, press [CHANNEL] to go from

one channel to another. The kinetic wave display on the channel

number indicates if the reception of that particular channel is in

good order.

If no readings are received from one particular channel for more

than two minutes, blanks “---” will be displayed until further

readings are successfully searched. Check if the remote unit

is sound and secure. You can wait for a little while or press

[CHANNEL] and [MEMORY] simultaneously to enforce an

immediatesearch. Ofcourse noreadingwill beshownif noremote

unit is assigned to that channel.

If the temperature goes above or below the temperature measuring

range of the main unit or the remote unit (stated in specification),

the display will show “HHH” or “LLL”.

TEMPERATURE TREND

The temperature trend indicator on the screen shows the trend of

samplings collected at that particular remote site. Three trends,

rising, steady and falling, will be shown.

MAXIMUM AND MINIMUM

TEMPERATURES

The maximum and minimum recorded indoor temperatures and

those of outdoor channels will be automatically stored in memory.

To display them:

1. Select the channel to be checked.

2. Press [MEMORY] once to display the maximum temperature

and again the minimum temperature.The respective indicators,

MAX or MIN will be displayed.

Toclearthememory,holddown[MEMORY]fortwoseconds.The

maximum and minimum temperatures will be erased. If you press

[MEMORY] now, the maximum and minimum temperatures will

have the same values as the current ones until different readings

arerecorded.

Arrow

indicator

Temperature

Trend Rising Steady Falling

NOTE ON °C AND °F

The unit of temperature display is selected with the °C/°F slide

switch. Select °C for Centigrade or °F for Fahrenheit.

Note that the remote temperature display on the main unit is

dominated by the selection on the °C/°F slide switch of the main

unit. Whatever the display units of the remote sensors are, they

will be automatically converted to the chosen one of the main unit.

HOW TO READ THE KINETIC WAVE

DISPLAY

The kinetic wave display shows the signal receiving status of the

main unit. There are three possible forms:

DISCONNECTED SIGNALS

If without obvious reasons the display for a particular channel

goes blank, press [CHANNEL] and [MEMORY] to enforce an

immediate search. If that fails, check:

1. The remote unit of that channel is still in place.

2. The batteries of both the remote unit and main unit. Replace as

necessary.

Note: When the temperature falls below freezing point, the

batteries of outdoor units will freeze, lowering their voltage

supply and the effective range.

3. The transmission is within range and path is clear of obstacles

and interference. Shorten the distance when necessary.

TRANSMISSION COLLISION

Signals from other household devices, such as door bells, home

security systems and entry controls, may interfere with those of

this product and cause temporary reception failure.This is normal

and does not affect the general performance of the product. The

transmission and reception of temperature readings will resume

once the interference recedes.

The unit is in searching mode.

Temperature readings are

securely registered.

No signals.

ABOUT RADIO RECEPTION

The RMR182 is designed to automatically synchronize its calen-

dar clock once it is brought within range of the Frankfurt DCF77

radio signal.

When the RMR182 is within range, its radio-control mechanism

will override all manual settings.

When the unit is receiving radio signal, the radio reception signal

will start to blink.A complete reception generally takes about 2 to

10 minutes, depending on the strength of the radio signal.

When the reception is complete, the radio reception signal will

stop blinking. The strength of the reception in the last hour will be

indicated.

For better reception, place the clock away from metal objects and

electrical appliances to minimize interference.

- Strong

- Weak

- No Reception

- Receiving

CALENDAR CLOCK DISPLAY MODES

The RMR182 supports four display modes in the sequence of:

MODE 1. LocalTime

Hour, Minute, Second

----------------------------

Day, Month

MODE 2. LocalTime

Hour, Minute, Weekday

-------------------------------

Day, Month

MODE 3. LocalTime/SecondTime-ZoneTime

(localtime)Hour,Minute,Weekday

----------------------------------------

(Secondtime-zonetime)Hour,Minute

MODE 4. SecondTime-Zone

Hour, Minute, Weekday

------------------------------

Day, Month

Each press on the [SET/MODE] button will toggle the display in

the above order.

Note: The bottom line of the display will be replaced by the alarm

time if the [(( • ))] button is pressed.

If you wish to disable the auto-reception feature, press the

button for three seconds. The radio reception signal will disap-

pear. The unit will not respond to radio signals.

To enable the feature again, press the button for three seconds.

The radio reception signal will start blinking to initiate reception

automatically.

HOW TO SET THE CLOCK MANUALLY

To set the clock manually, hold [SET/MODE] for three seconds.

The display will return to MODE 1, with the hour digits blinking.

Use or to select the hour. Keep pressing the button will

increase or decrease the value rapidly.

Press [SET/MODE] to confirm. The minute digits will blink.

Repeat the same procedure to set the minutes, then the day-of-

month, month, display language, weekday and offset for the

second time zone.

Note that the time and date are displayed in 24-HOUR clock and

DAY-MONTH format, respectively. For display language, you

can choose among English (E), German (D), French (F) and

Italian (I) in order. Weekday is the usual sequence of Monday

through Sunday.

For the second time zone, which is indicated by the ZONE ICON,

enter the hour offset using the or buttons and the RMR182

will calculate the second time accordingly. For details, please refer

to the section “Time ZoneAnd Offset Table”.

If there is an item you do not wish to change, simply press

[SET/MODE] to bypass the item.

When you are done, press [SET/MODE] to exit. The display will

return to the mode last chosen.

HOW TO SET AND ARM THE ALARMS

TheRMR182hastwo alarms,ALARM1 andALARM 2.Theycan

be invoked together or independently.

To set an alarm:

1. Press [(( • ))]once toselectALARM1 oragain toselectALARM

2. The last selected time of the alarm will be displayed. If you

have never set the alarm before, the time will be displayed as

0:00.

2. Press [(( • ))] for three seconds. The hour digits will blink.

3. Enter the hour using or .

4. Press [(( • ))]. The minute digits will blink.

5. Enter the minutes using or .

6. Press [(( • ))] to exit.

The alarm ON icon [ ] for the alarm chosen will be displayed

indicating the alarm set above is now armed.

Youcanalsoarmordisarmanalarmbypressingthe[ALON/OFF]

button.

HOW TO STOP ANALARM

To stop an alarm, you can use either [(( • ))] or [AL ON/OFF].

Pressing [(( •))] will stop the alarm, which is still armed and will go

off at the set time the following day.

If [AL ON/OFF] is pressed instead, the alarm will be stopped and

deactivated all together.

When the alarm goes off the sound which will gradually increase

in volume and repeating speed will be turned on for about 2

minutes unless the [(( • ))] or [AL ON/OFF] button is pressed to

mute the alarm. If neither key is pressed within these 2 minutes,

the alarm will be repeated once after approx 8 minutes.

PRECAUTIONS

This product is engineered to give you years of satisfactory

service if you handle it carefully. Here are a few precautions:

1. Do not immerse the unit in water.

2. Do not clean the unit with abrasive or corrosive materials.They

may scratch the plastic parts and corrode the electronic circuit.

3. Do not subject the unit to excessive force, shock, dust,

temperature or humidity, which may result in malfunction,

shorter electronic life span, damaged battery and distorted

parts.

4. Do not tamper with the unit's internal components. Doing so

will invalidate the warranty on the unit and may cause unnec-

essary damage. The unit contains no user-serviceable parts.

5. Only use fresh batteries as specified in the user's manual. Do

not mix new and old batteries as the old ones may leak.

6. Always read the user's manual thoroughly before operating the

unit.

TIME ZONE AND OFFSET TABLE

Andere Handbücher für RMR182

Inhaltsverzeichnis

Andere Oregon Scientific Thermometer Handbücher

Oregon Scientific

Oregon Scientific RMR382A Bedienungsanleitung

Oregon Scientific

Oregon Scientific RMR382 Bedienungsanleitung

Oregon Scientific

Oregon Scientific RGR126NX Bedienungsanleitung

Oregon Scientific

Oregon Scientific RMR262 Bedienungsanleitung

Oregon Scientific

Oregon Scientific RGR126 Bedienungsanleitung

Oregon Scientific

Oregon Scientific AW133 Bedienungsanleitung

Oregon Scientific

Oregon Scientific RMR383HG Bedienungsanleitung

Oregon Scientific

Oregon Scientific RGR126 Bedienungsanleitung

Oregon Scientific

Oregon Scientific EW91 Bedienungsanleitung

Oregon Scientific

Oregon Scientific RMR112 Bedienungsanleitung

Oregon Scientific

Oregon Scientific RAR232 Bedienungsanleitung

Oregon Scientific

Oregon Scientific RAR188A Bedienungsanleitung

Oregon Scientific

Oregon Scientific EMR812A Bedienungsanleitung

Oregon Scientific

Oregon Scientific THT328 Bedienungsanleitung

Oregon Scientific

Oregon Scientific SA880SSWR Bedienungsanleitung

Oregon Scientific

Oregon Scientific RMR803A Bedienungsanleitung

Oregon Scientific

Oregon Scientific RAR213HG Bedienungsanleitung

Oregon Scientific

Oregon Scientific RMR686P Bedienungsanleitung

Oregon Scientific

Oregon Scientific AW131 Bedienungsanleitung

Oregon Scientific

Oregon Scientific BAR122HGLA Bedienungsanleitung

Oregon Scientific

Oregon Scientific RMR112A Bedienungsanleitung

Oregon Scientific

Oregon Scientific EW92 Bedienungsanleitung

Oregon Scientific

Oregon Scientific EM899 Bedienungsanleitung

Oregon Scientific

Oregon Scientific AW129 Bedienungsanleitung

Beliebte Thermometer Handbücher anderer Marken

Delton

Delton 981A Bedienungsanleitung

Baker

Baker MM2P Bedienungsanleitung

Tarmo

Tarmo 320281 Bedienungsanleitung

Citizen

Citizen CTD 504 Bedienungsanleitung

TFA

TFA 14.1500 Bedienungsanleitung

Vive

Vive DMD1010 Bedienungsanleitung

Gotemp

Gotemp THB4002 Bedienungsanleitung

GREISINGER

GREISINGER G 1202 Bedienungsanleitung

Amprobe

Amprobe TMD-53W Bedienungsanleitung

Trotec

Trotec BP10 Bedienungsanleitung

Radiance instruments

Radiance instruments RT616 Series Bedienungsanleitung

Eurolec

Eurolec IR151 Bedienungsanleitung

Scaneo

Scaneo TS42B Bedienungsanleitung

Sper scientific

Sper scientific 800043 Bedienungsanleitung

Microlife

Microlife NC 200 Bedienungsanleitung

Motorola

Motorola MBP69SN Konfigurationshandbuch

The MeatStick

The MeatStick The MeatStick Bedienungsanleitung

Hama

Hama TH35-A Bedienungsanleitung