Oricom CARE120 Bedienungsanleitung

CARE120

Amplified Phone with Caller ID

User Guide

Keep this user guide for future reference. Always retain your proof of

purchase in case of warranty service and register your product on line at:

AUSTRALIA: www.oricom.com.au

General Information

Warnings

It is very important that you read the User Guide carefully as it

contains detailed information on installation, programming and

operational issues which you will need to be aware of to ensure the

Care Phone operates properly. Following is a list of some of the

important issues and important warnings which you need to be aware of.

This is a summary of the important issues you must still read the

User Guide in full.

Warnings

The telephone is designed for indoor use only. Do not install the

telephone in areas where there is the risk of an explosion, excessive

exposure to smoke, dust, vibrations, chemicals, moisture and heat.

Do not use your telephone during an electrical thunderstorm as it

is possible to get an electric shock. Refer to information

contained in Telstra White pages directory.

The earpiece of the handset may attract small metal objects

such as staples and pins. Care should be taken when placing the

handset near these items.

Setting the receiver volume to maximum may, under some

situations cause ear damage. We suggest returning the handset

volume control to the “0” position after each call.

Do not install in damp locations such as a bathroom or laundry,

do not expose the unit to direct sunlight.

Need Help?

If you need assistance setting up or using your Oricom product now or in

the future, call Oricom Product Support.

Australia 1300 889 785

www.oricom.com.au

Mon-Fri 8am – 6pm AEST

New Zealand 0800 67 42 66

www.oricom.co.nz

Mon-Fri 10am – 8pm NZST

Notes for operation in New Zealand

The grant of a Telepermit for any item of terminal equipment

indicates only that Telecom has accepted that the item complies with

the minimum conditions for connection to its network. It indicates no

endorsement of the product by Telecom, nor does it provide any sort

of warranty. Above all, it provides no assurance that any item will

work correctly in all respects with another item of Telepermitted

equipment of a different make or model, nor does it imply that any

product is compatible with all of Telecom’s network services.

This equipment shall not be set to make automatic calls to the

Telecom “111” Emergency Service.

This equipment may not provide for the effective hand-over of a call

to another device connected to the same line.

This equipment should not be used under any circumstances that

may constitute a nuisance to other Telecom Customers.

REN (RN for New Zealand)

The REN (Ringer Equivalence Number) or (RN) is of significance

only if you wish to connect more than 1 telephone to your telephone

line. A standard telephone line has a maximum REN capacity of 3

(RN of 5). It is possible to connect 3 devices with a REN of 1 (RN of

1) with no degradation to the product’s performance. Exceeding this

limit may cause the volume of the ringer in any phone to decrease or

not ring at all.

Caller ID

Customers using non Telecom toll services should not use the dial

back feature for local calls as this will incur a charge only the 7 digit

number should be dialed. Some of the CID services listed may not

be available in New Zealand.

Location of Controls

345

CID

NEW

DELETE

CALL/BACK

REDIAL

MEM

STORE

RECALL

BOOST

1. Power adapter socket

2. Telephone line socket

3. Hook switch

4. Delete button

5. Handset holder

6. Call back button

7. One touch button(M1/M2)

8. Keypad

9. Coil cord socket

10.Receiver volume controller

11.Amplify LED indicator

12.Amplify key

13.Extra shaker socket

14.New call LED

15. Ring Hi/Mid/Off switch

16. Up /Down keys

17. Memory button

18. Caller ID button

19. Tone Hi/Low switch

20. Phonebook button

21. Store number button

22. Recall button

23. Speaker Volume

Hi/Low switch

24. Redial button

25. Speaker button

26. Ring LED indicator

Installation

Installing batteries in the phone

Warnings

You must install 4 AA batteries in the phone base. The battery

back up system will then be able to power the unit for up to 12

hours if there is a mains power failure.

If your mains power has been turned off for an extended period

or the power supply to the phone has been unplugged from

mains power you should replace the batteries with 4 new high

uality AA batteries.q

Before opening the battery compartment, make sure the

telephone is disconnected from the telephone line and the

mains power supply.

1. Use a flat-blade screwdriver or tip of a pen to lift and remove the

battery compartment door.

2. Insert four AA batteries into the compartment as indicated by the

polarity symbols.

3. Snap the battery compartment door back into place.

When this symbol appears on the display or the display dims,

replace the batteries. Always use 4 new high quality AA batteries.

Connecting the telephone

1. Plug one end of the telephone cable supplied into the TEL. LINE

jack at the back of the telephone base.

2. Plug the other end of the telephone cable into the wall outlet.

3. Plug one end of the curly cord into the socket on the handset.

4. Plug the other end of the curly cord into the left side of the

telephone.

Wall Mounting

Method A. To fit to an existing telephone wall plate with modular

connector simply,

1. Press and lift out the handset holder on

base. Rotate it 180°, and snap it into

place (see Fig A) so it will hold the

handset in place when the phone is

mounted on the wall.

444

Fig A

Fig B

2. Insert the mounting bracket’s two tabs

into the matching slots on the phone’s

base. (see Fig B)

3. Then press down and slide the bracket

Upward until the tabs snap into place.

4. Plug the short telephone line cord

(supplied) into the base of the phone and

plug the other end into the telephone

wall plate socket.

5. Position the mounting holes on the base

of the phone over the two protruding

screws on the wall plate. Gently push the

phone flush against the wall plate then

slide the phone downwards locking it

into place.

Method B. Attach directly to a wall

1. Drill two holes vertically, one above the other, 83mm apart, and

leave the screws protruding from the wall by 5mm.

2. Follow steps 1 and 2 above.

3. Then press down and slide the bracket upward until the tabs

snap into place.

4. Plug one end of the telephone cable into the TEL. LINE jack at

the back of the base.

5. Plug the other end of the telephone cable into the telephone

socket, then align the base’s keyhole slots with the screws and

slide the phone downward to secure it.

Basic settings

1. After installing the batteries, the display should flash the word

“ENGLISH”. If not, press and hold for approximately 4

seconds.

2. Select the desired language using or . Press DELETE

button.

3. Select the desired contrast setting (2=Default) using or .

Press DELETE button.

4. Set the hour (00-23) using or . Press DELETE button.

5. Set the minute using or . Press DELETE button.

6. Set the day using or . Press DELETE button.

7. Set the month using or . Press DELETE button.

If you wish to change the language, contrast, time settings at a later

date, press and hold button for approximately 4 seconds and

repeat steps 2-7 above.

Operation

When the telephone is not in use, the date and time, number of new

and total number of calls STORED in the Caller ID MEM will be

shown in the display. The display will show the caller number (and

name if available).

Making a call

1. Pick up the handset or press SPEAKER button (the speaker LED

will light) and wait for a dial tone.

2. Dial the number you wish to call. The display will show the

number that you are dialing. If you dial a number over 14 digits

long, it will show the last 14 digits only.

3. When you have completed your call, hang up the handset or

press the SPEAKER button again to release the telephone line.

It is possible to switch from a handset to speakerphone conversation

by pressing the SPEAKER button and picking up or hanging up the

handset accordingly.

Pre Dialing a Call

1. Dial the number you wish to call . To correct a number press the

DELETE button for each incorrect digit.

2. Pick up the handset or press the SPEAKER button.

Receiving a Call

When you receive a call, the telephone rings, the Ringer LED flashes,

and the display shows the CALL# and the caller telephone number

(with caller ID service activated).

This feature allows you to decide to pick up the phone or not

depending on who is calling.

If you want to talk to the caller:

1. Pick up the handset or press SPEAKER button to answer the

call.

2. At the end of the call, return the handset to the cradle or press

SPEAKER button again.

Redial function

If a number that you have dialed is engaged or you were unable to

get through to anybody. The last number dialed will be saved in the

telephone automatically.

To use the redial facility, proceed as follows:

1. Lift the handset or press SPEAKER button.

2. Press the REDIAL button. The last saved redial number will now

be dialled.

Pause

If needed for phone banking or behind a PBX system. You can insert

a 3.6 seconds pause while dialing or storing a number into MEM.

Press REDIAL button at the desired point in number to insert a

pause.

Recall and call waiting

Press the Recall button followed by the extension number to transfer

calls when connected to a PBX.

Access to additional network services can be gained by using the

Recall button * and # keys. Contact your network operator for more

information.

To Turn on Telstra call waiting (Australia)

You can use the recall button to answer a second call while you are

on the phone. However this service will need to be turned on. For

example to turn on Telstra’s Call Waiting service:

1. Lift the handset and wait for dial tone then Press *43#.

2. You will hear the service message and then hang up.

Take two different calls at the same time

During a call, you will hear two loud beeps periodically to notify you

of another incoming call. If you wish to answer this call

1. Press Recall button listen for dial tone then Press 2 to put the

current call on hold and talk with the second caller.

2. Subsequent presses of Recall button listen for dial tone then

Press 2 will toggle you between these 2 callers.

Call Timer

Immediately after dialling a telephone number a call timer will be

shown on the display. The timer is a simple way to help you keep

track of how long the call lasts.

Ringer Volume Control

The ringer sound level can be adjusted by sliding the RINGER

switch to select high (HI) or soft (MID) sound level. When you don’t

want to be disturbed, slide the RINGER switch to the Off position.

The bright Red light (LED) on the base will flash with all incoming

calls.

Volume Control

Handsfree Speaker Volume Control

You can adjust the hands free speaker volume level by simply sliding

the VOLUME switch located on the side of the phone.

Receiver volume control

The receiver volume control enables you to adjust the receiver

volume on the handset. Press the BOOST button, the red LED will

turn on, now you can increase the receiver volume by rotating the

knob (under the receiver) to the desired level ( level 1 to level 9).

Receiver Tone Volume Control

You can use the TONE slide switch to adjust high frequency sounds.

Words are clearer and easier to understand. Note: The tone

adjustment function will not work if the receiver volume is set to the

minimum level.

Shaker operation

You can connect a shaker accessory (not included) to the socket

marked Ext.Trig located at back of your telephone. The shaker will

vibrate when you receive an incoming call.

To purchase a suitable shaker unit in Australia (Model no. VIB100PS)

contact Oricom direct on (02) 4574 8888.

Note: The SHAKER function can only be activated when the power

adaptor is connected (power adaptor supplied with Shaker unit).

VIB1000PS

Inhaltsverzeichnis

Andere Oricom Telefon Handbücher

Oricom

Oricom TP6 Bedienungsanleitung

Oricom

Oricom HP200 Bedienungsanleitung

Oricom

Oricom CARE80S Bedienungsanleitung

Oricom

Oricom TP9 Bedienungsanleitung

Oricom

Oricom Care10 Bedienungsanleitung

Oricom

Oricom TP58 Bedienungsanleitung

Oricom

Oricom TP9 Bedienungsanleitung

Oricom

Oricom HP100 Bedienungsanleitung

Oricom

Oricom TP110 Bedienungsanleitung

Oricom

Oricom CARE920-1 Bedienungsanleitung

Oricom

Oricom CARE90 Bedienungsanleitung

Oricom

Oricom TP88 Bedienungsanleitung

Oricom

Oricom CARE95 Bedienungsanleitung

Oricom

Oricom TCR10 Bedienungsanleitung

Oricom

Oricom Pro900 Bedienungsanleitung

Oricom

Oricom Loud Clear TP1100 Bedienungsanleitung

Oricom

Oricom BT9500 Bedienungsanleitung

Oricom

Oricom TP30 Bedienungsanleitung

Oricom

Oricom TP170WP Bedienungsanleitung

Oricom

Oricom CARE80 Bedienungsanleitung

Oricom

Oricom care60 Bedienungsanleitung

Oricom

Oricom TP29 Bedienungsanleitung

Oricom

Oricom TP68 Bedienungsanleitung

Oricom

Oricom TP30 Bedienungsanleitung

Beliebte Telefon Handbücher anderer Marken

GE 2-9480 Bedienungsanleitung

Geemarc

Geemarc PHOTOPHONE 155 Bedienungsanleitung

Interquartz

Interquartz Gemini IQ333 Bedienungsanleitung

SSS Siedle

SSS Siedle HT 840-0 Bedienungsanleitung

Motorola

Motorola TITANIUM Bedienungsanleitung

Panasonic

Panasonic ICX Bedienungsanleitung

LG H870DS Bedienungsanleitung

Samsung

Samsung GT-I9500 Bedienungsanleitung

AT&T

AT&T Trimline 205 Bedienungsanleitung

Selta

Selta zenyth 600 Bedienungsanleitung

Doro

Doro AFTI 20 Bedienungsanleitung

UNIQCELL

UNIQCELL A1 Bedienungsanleitung

Jabra

Jabra SP5050 - Bluetooth hands-free Speakerphone Bedienungsanleitung

BT Decor 425 Bedienungsanleitung

NEC

NEC SV8500 Bedienungsanleitung

Teledex

Teledex PEARL Bedienungsanleitung

Ericsson

Ericsson Dialog 3213 Bedienungsanleitung

Yealink

Yealink VP530 Bedienungsanleitung