ORTNER ABS Combustion Control V2.2 Bedienungsanleitung

Operating ManualOperating Manual
LED
WLAN
DISPLAY
of the ORTNER Combustion Control V2.2
ORTNER control installed on:
Serial number

ORTNER Inside: ORTNER Speicherecke 09-70/40/38, Design: black

Page 3
Tabl of content
One control, three display options ���������������������������������������������������������������������������������4
General function ���������������������������������������������������������������������������������������������������������5
Important information �������������������������������������������������������������������������������������������������6
Initial start-up�������������������������������������������������������������������������������������������������������������6
LED variant ����������������������������������������������������������������������������������������������������������������8
Visualization of the combustion phases with LED ����������������������������������������������������������8
Combustion phases and colour description ��������������������������������������������������������������������8
Display variant �������������������������������������������������������������������������������������������������������� 10
Visualization of the combustion phases with glass display �������������������������������������������� 10
Indications on the display of each heating phase���������������������������������������������������������� 10
WLAN variant ����������������������������������������������������������������������������������������������������������� 12
Visualization of the combustion phases with LED �������������������������������������������������������� 12
Visualization of the combustion phases via the WLAN module ������������������������������������� 12
Installation of the WLAN module with mobile devices�������������������������������������������������� 13
Integration in an existing personal network ����������������������������������������������������������������� 14
Integration has failed� Now what?������������������������������������������������������������������������������� 16
Error messages and their correction ���������������������������������������������������������������������������� 18
Heating up errors ������������������������������������������������������������������������������������������������������ 18
Defective sensor��������������������������������������������������������������������������������������������������������� 18
Temperature at rest���������������������������������������������������������������������������������������������������� 19
No power supply �������������������������������������������������������������������������������������������������������20
Door open, although the door is closed ������������������������������������������������������������������������20
Door closed, although the door is open ������������������������������������������������������������������������ 21

On contro uni, thre displa option
The ORTNER Combustion control (ABS) offers 3 different options:
• ORTNER control with LED display
• ORTNER control with LED display and WLAN
• ORTNER control with display (black or white)
The ORTNER combustion control. Simple and elegant. Fig.1: LED variant, Fig.2: Display black, Fig.3: WLAN view on smartphone
1
23

Page 5
Genera nctio
The heating process of an oven system is divided into various burning phases / stages:
1� Standby phase
2� Heating up phase
3� Heating phase
4� Embers phase
5� Standby phase
The ORTNER Combustion control ensures an optimal sequence of the burn-off phases
of the furnace installation� Components such as the sensor and the combustion air ap
ensure accurate control, which not only ensures ease of operation, but also maximum
efciency�
By determining the maximum temperature in the heating phase, and a calculation based
thereon, the optimum shutoff time of the combustion air ap is dened� At this time, the
combustion air damper is automatically closed and the embers phase begins� In this phase,
an open combustion air ap would lead to an undesirable, faster cooling of the furnace
installation�
Thanks to the control, the maximum heat output is achieved, which is delivered to the
room as a soothing heat radiation�
A correct combustion
is critical in order to
enable the pleasant
prolonged heat radiation
in the room.
Shown here: ORTNER
Storage corner 09-70/40/38

Important information
The correct amount of combustion air is a
deciding factor for optimal combustion� It affects
the degree of efciency, i�e� the amount of energy
that can be extracted from the wood� Furthermore,
it ensures an optimal air volume for a clean burn,
clean observation windows and an environmentally-
friendly combustion� When the optimal closing time is
reached, the storage of the masonry heater is not
cooled by the supply of fresh air and as a result
does not reduce the storage duration� The ORTNER
combustion control safeguards the optimal energy yield
with a maximum degree of safety�
In the event of a power failure, the
combustion air register of the control unit
is opened automatically�
Initial start-up
During the initial start-up and restart as well as
following a power failure, for safety reasons, the
control always starts in the heating up phase and the
combustion air register remains open� Therefore,
in the event of a power failure during the heating
process, the fuel is burnt safely�
In the event that the temperature is
>50°C - <250°C following a power failure,
the control remains in the heating up phase�
When the temperature is >250°C, the control switches
to the heating phase�
When the temperature remains below a temperature
of 50°C during a waiting period of 60minutes,
the control will return to the standby mode� Only then
will the combustion air register close again�

Page 7
ORTNER Inside: ORTNER Grundofen 11-42/59, Appearance: Traditional tile-green

LED varian
The LED variant is the most basic of the ORTNER control range. This visualization of
the ABS displays the different combustion levels in the most simplest manner.
Visualization of the combustion phases with LED
Combustion phases and colour description
The control is in the standby mode
Standby state:
• The stove is not heated
• The temperature in the combustion chamber is <50°C
• The combustion air register is closed
The door(s) are opened for heating up
Door open:
• The door is open for the insertion the fuel
• The combustion air register opens
The masonry heater is in the heating up phase:
Heating up state:
• Is activated with the closure of the door
• The combustion air register is open
• The temperature in the combustion chamber is <250°C
Green
Standby mode
Blue
Door open
Orange
Heating up Red
Heating
<600°C
Purple
Ember phase
Light purple
Heating
>600°C
Red
Heating
<600°C

Page 9
The masonry heater switches to the heating phase:
Heating state
• Is activated from a temperature of >250°C
• The combustion air register is open
• The maximum temperature is stored
• Determination of the optimal transition temperature to embers
The masonry heater switches to the heating phase >600°C:
Heating state
• The temperature increases to >600°C
• The combustion air register is open
• The maximum temperature is stored
• Determination of the optimal transition temperature to embers
The masonry heater switches to the heating phase >600°C:
Heating state
• The temperature drops to <600°C
• The combustion air register is open
The masonry heater switches to the embers or storage phase:
Embers state:
• Is activated when the optimal transition temperature is reached
• The combustion air register closes
• The embers phase begins
• Optimal heat storage is enabled
Renewed refuelling with wood in order to increase the storage duration
Door open:
• In the event that wood should be added again for combustion, this
should be performed during the embers phase� In this case, the combustion
starts again� When relling on the still fresh embers, only add half the wood
amount�

Indications on the display of each heating phase
Status of the standby mode:
• The stove is not heated
• The temperature in the combustion chamber is <40°C
• The combustion air register is closed
• The display is dimmed
Line 2 on the display: Status: Standby mode
Displa varian
All important data is presented on the display during the combustion� In this manner,
you can continuously see the temperature and the status of the heating process� When the
control switches into the embers phase, the display will dim� Only when a new combustion
is begun will the display light up again brightly and all status messages will be displayed�
Visualization of the combustion phases with glass display
Current temperature
Current
combustion phase &
status messages on
temperature 2
(if present)
Inhaltsverzeichnis

















