Osburn 45 Series Leitfaden
29-10-2013
! !
Maintenance(45(Serie(
2
CAUTION
Before resetting your electronic
card that displays an error code.
Error Code H
•Service the stove COMPLETELY as described in this
manual.
•Check the chimney pipe.
Error Code O
•Service the stove COMPLETELY as described in this
manual.
•Check the chimney pipe Check the convection fan.
Error Code P
•Check that the Pressure switch pipe is not blocked.
THIS STOVE IS EQUIPPED WITH MULTIPLE DEVICES TO ENSURE YOUR SAFETY. HOWEVER
IF A WARNING ERROR CODE STOPS YOUR STOVE ON SEVERAL OCCASIONS, THERE ARE
GREAT CHANCES THAT THE STOVE DOES NOT EXHAUST PROPERLY. YOU HAVE THE
RESPONSIBILITY TO MAKE SURE THAT THE MAINTENANCE OF THE STOVE IS DONE AS
DESCRIBED IN THIS DOCUMENT.
UNPLUG THE STOVE BEFORE THE MAINTENANCE
! !
Maintenance(45(Serie(
3
MINIMUM RECOMMANDED MAINTENANCE SCHEDULE
Components
Daily
Weekly
Or after
+/- 10 bags
Monthly
Or after
+/- 25 bags
Annually
Or
Per ton of pellets
Burn Pot
Empty
Empty and Brush
Glass
Wipe
Clean
Heat Exchanger
Tubes
Activate the cleaning
rod every time you
load the stove
Activate the cleaning rod
and vacuum
Baffle
Empty and brush
Convection Blower
Filters
Vacuum
Ashe Drawer
Empty
Combustion
Chamber
Vacuum
Vacuum and Brush
Left-hand Channel
Vacuum
Exhaust Blower
Vacuum
Pressure Switch Tap
Brush
Venting System
Inspect
Sweep
Gaskets
Inspect
Hopper
Empty and Vacuum
The user must be able to evaluate the frequency depending on the level of dirt in the burn pot.
A pot that is dirty will reduce the efficiency of the stove and cause problems.
!
Maintenance(45(Serie(
4
REMOVE THE BAFFLE.
1. Lift the baffle and slide forward it a little to
clear the supports.
2. Lower the baffle until the tab is behind the
burn pot receptacle.
3. Rotate the baffle and align the right corner
to the upper right corner of the door
opening.
4. Continue rotating the baffle to remove it
completely.
RECOMMENDED MAINTENANCE
WEEKLY
OR AFTER
+ / - 10 BAGS
!
Maintenance(45(Serie(
5
CLEAN THE HEAT EXCHANGER TUBES.
The cleaning rods must be
activated as often as possible.
#1 Pull and push the rod 4-5
times.
#2These rods activate a rake that
cleans the heat exchanger tubes.
Note: The stove will produce
more heat if the heat exchanger
tubes are clean.
RECOMMENDED
MAINTENANCE
DAILY
(It is not necessary to remove
the baffle every day.)
!!
!
1
2
Maintenance(45(Serie(
6
CLEAN THE EXHAUST DUCTS
To access the exhaust
ducts, remove the wall on
the left side of the burning
pot.
1. Remove 3 screws on
the right and 2 screws
left side of the panel.
2. Toggle the wall and
remove it from the
stove.
1
2
Maintenance(45(Serie(
7
CLEAN THE EXHAUST DUCTS
NEXT.
It is difficult to insert the vacuum hose into the
openings. Using a ¾inch hose installed on a
vacuum adapter will facilitate access to these
tight spaces.
The cleaning of the exhaust ducts is made of 3
important openings. #1. A rectangle in the
bottom and #2 A triangle at the top and also
#3 opening above the heat exchanger tubes.
It is possible that an ash wall is formed and
blocks the opening located above the tubes.
This opening is not accessible with the
vacuum hose.
To clean the #3 opening above the tubes, drag
a rigid rod between the tubes and the opening
to break down the accumulation. (Make sure
the top opening is free from any
accumulation).
Once cleaned, reinstall the left wall following
the reverse instruction
RECOMMENDED MAINTENANCE
MONTHLY
OR AFTER
+ / - 25 BAGS
1
2
3
Maintenance(45(Serie(
8
CLEAN THE BURN POT.
Using a scraper and a wire brush,
thoroughly clean the surface of the burn
pot. It is very important to leave no
residue on the surface of the burn pot.
Note: The sand and dirt contained in
the wood pellets does not burn and
solidifies to form a stone on the surface
of the burn pot. This stone is commonly
called (clinker) in the pellet stove
industry.
If the (Clinker) is not removed the
combustion air holes are blocked or
reduced and this will also reduce the
efficiency of the stove and increases
thereby forming (clinker) until the
combustion becomes almost
impossible.
RECOMMENDED MAINTENANCE
WEEKLY
EMPTY AND SCRAPE
Maintenance(45(Serie(
9
CLEAN THE BURN POT RECEPTACLE
!
After removing the burn pot vacuum the
ash within the burn pot receptacle.
THE ASH DUMP CAP MUST BE IN
PLACE.
Vacuum the ash at the bottom of the
pan and make sure the ash dump plug
is in place and tight.
RECOMMENDED MAINTENANCE
DAILY
EMPTY
INSTALL 2 GASKETS IN THE
RECEPTACLE BEHIND THE BURN POT.
It is important to insert 2 Gaskets into
the receptacle behind the burn pot.
In the absence of gaskets the stove will
not light easily.
RECOMMENDED MINIMUM
MAINTENANCE
WHEN NEEDED
Maintenance(45(Serie(
10
CLEANING THE EXHAUST FAN
The Access to the exhaust
fan is on the left side of the
pedestal.
Follow these steps To
remove the left panel of the
pedestal.
1. Unscrew the 2 retaining
screws located behind
the panel.
!
2. Pull the panel.
3. Push the panel forward.
1
2
3
Inhaltsverzeichnis
Andere Osburn Herd Handbücher
Osburn
Osburn BRITANNIA 31 Bedienungsanleitung
Osburn
Osburn 1100 Bedienungsanleitung
Osburn
Osburn OB01601 Bedienungsanleitung
Osburn
Osburn 1100 Bedienungsanleitung
Osburn
Osburn Inspire 2000 OA10243 Bedienungsanleitung
Osburn
Osburn 2300 Bedienungsanleitung
Osburn
Osburn Hybrid-35MF Bedienungsanleitung
Osburn
Osburn Romance 28 Bedienungsanleitung
Osburn
Osburn OSBURN 1000 Bedienungsanleitung
Osburn
Osburn OSBURN 1000 Bedienungsanleitung
Beliebte Herd Handbücher anderer Marken
Vermont Castings
Vermont Castings Intrepid 2 Bedienungsanleitung
Italiana Camini
Italiana Camini CLASSICA Kurzanleitung
Avalon
Avalon Vashon Avanti DVS FS Bedienungsanleitung
Spartherm
Spartherm ambiente a1 Bedienungsanleitung
Dimplex
Dimplex MCFSTV12AU Bedienungsanleitung
Warmlite
Warmlite WL46040 Bedienungsanleitung