OSF Alarm-control.plus Bedienungsanleitung

Installation and Operation Manual

Alarm-control.plus

Leak warning device

with integrated webserver

Technical data

Dimensions:

220mm x 285mm x 80mm

Operating voltage:

230V/50Hz

Power consumption:

<10 W

Load capacity of the potential-free contact:

max. 8A (230V)

Switching capacity of the 230V output:

max. 4A (AC1)

Protection class:

IP 40

Number of inputs for water sensors:

Operating voltage of the water sensors:

12V AC (SELV)

Climate sensor input:

digital sensor system „Klima 2“

Ambient temperature:

0-40°C

Air humidity:

0-95% non condensing

Art.No.: 310.010.0015

Installation and operating manual for Alarm-control.plus page 2 (10)

Table of contents

Table of contents .................................................................................................................................2

General description.............................................................................................................................2

General instruction .............................................................................................................................3

Mounting.............................................................................................................................................3

Electrical Connection..........................................................................................................................3

Connection of the water sensors ..................................................................................................................4

Two-electrode water sensor ........................................................................................................4

Float switch..............................................................................................................................4

Climate sensor connection............................................................................................................................4

Connecting to LAN .......................................................................................................................................4

Connection to the pool control PC-45 exclusiv...........................................................................................5

Connection to a “Smart-Touch” operating panel ......................................................................................5

Setup and configuration .....................................................................................................................6

Configuration from the PC-45 exclusiv............................................................................................6

Alarm-control.plus menu .............................................................................................................................6

Alarm settings for water sensors..................................................................................................................6

Alarm settings for climate sensor ................................................................................................................6

Connect to a computer network and the Internet..............................................................................7

Use of the communication server.........................................................................................................7

Webserver ............................................................................................................................................8

Alarm settings for water sensors..................................................................................................................8

Alarm settings for climate sensor ................................................................................................................8

Service settings ..............................................................................................................................................8

Climate sensor configuration.......................................................................................................9

Configuration of the water sensors...............................................................................................9

Fuses....................................................................................................................................................9

Factory setting.....................................................................................................................................9

Wiring diagram .................................................................................................................................10

General description

The electronic control system Alarm-Control.plus signals water leaks in the technical room of the

pool. The device can signal alarms optically and acoustically, two relay outputs and automatic e-

mail are also available. Alarm-Control.plus can work independently or as an extension unit for the

PC-45-exclusiv system.

Up to 6 water sensors can be connected to the Alarm-control.plus unit. Suitable sensors are pairs

of immersion electrodes or float switches.

A climate sensor can optionally be connected to the device, which enables the air temperature

and humidity in the technical room to be monitored. If a parameter exceeds the set limit values, an

alarm can be triggered.

Installation and operating manual for Alarm-control.plus page 3 (10)

With the colored illuminated button on the front of the housing you can:

a) Switch off the Alarm-control.plus. The device is switched off by pressing the button for 3

seconds. When the device is switched off, the button does not light up and the device does not

respond to leak sensors. The Alarm-control.plus device is switched on again by pressing the

button again.

b) Briefly press the button to turn the alarm on and off temporarily. During the pause, the backlight

of the button lights up blue. The duration of the alarm pause is limited in time. The factory setting

is 30 minutes, maximum 3 hours. After the pause time, the Alarm-control.plus device automatically

switches to signaling.

The pause in the alarm enables service work to be carried out on the water sensors without them

being triggered.

When switched on, the button lights up green until an alarm is triggered. The button flashes red

during the alarm.

If the button is mostly green but flashes red every 5 seconds, it means that one of the leak

sensors has recently had contact with water. This state must be confirmed by briefly pressing the

button. General instruction

The control unit has been designed for safe and reliable operation in accordance with the

provisions of these operating instructions. Therefore, read these operating instructions carefully

before installing the device! The instructions contained therein for installation and operation must

be followed exactly. If these conditions are met, the control unit will work properly for many years.

Mounting

The housing is fixed vertically and permanently to a solid wall with adequate load-bearing

capacity. The place of installation must be dust-free and protected against water in order to ensure

that the device works properly. The ambient temperature should lie between 0° C and + 40° C and

should be as constant as possible. The relative humidity must not exceed 95% and no

condensation may occur. Direct incidence of heat or sunlight on the device must be avoided. The

control unit is not suitable for outdoor installation.

Electrical Connection

The control device must be fixed at a location where it is protected against moisture in accordance

with its class of protection. The power supply to the device must be fed via an all-pin main switch

with contact opening width of at least 3 mm and a residual current circuit breaker (RCCB) with IFN

30 mA. Before opening the housing, it is absolutely necessary to de-energize the device

electrically. The electrical connection as well as the work of adjustment and servicing

should be carried out only by an approved electrician! The connection diagrams enclosed

and the relevant safety provisions applicable must be observed and followed.

water sensor

with 2

immersion

electrodes

Mains

1/N/PE

230V 50Hz

Up to 6 water sensors of different types:

LAN-socket

LAN button

white

brown

green

yellow

sensor system

«Klima-2»

ALARM

Signal contact

potential-free

max. 8А

Motor-

valve

230V

max. 4А

Mini-

float switch

open

Installation and operating manual for Alarm-control.plus page 4 (10)

Low-voltage cables should not be laid along with three-phase or AC cables in the same

cable duct. In general, laying low-voltage cables near three-phase or AC cables must be

avoided.

Connection of the water sensors

Up to 6 water sensors can be connected to terminals 1-6. Depending on the requirements, a

distinction is made between two types of water sensors. For correct operation, the type of sensor

connected must be specified in the "Configuration" menu (see the "Configuration" section for more

details). The factory setting for the sensor type is "two-electrode water sensor".

Two-electrode water sensor

As the name suggests, a sensor of this type consists of two electrodes between which an

alternating electrical current flows when immersed in water. Suitable electrodes are

hanging electrodes made of stainless steel (Art. 303.000.0011) or another water sensor

with two bare contacts.

The sensor cable (at least 1.5mm²) can be extended up to 20 meters. The polarity of the

connection does not matter.

The two-electrode water sensor does not enable cable break detection. The advantage of

these sensors is the possibility of connecting several sensors in parallel to one input.

Float switch

A suitable float sensor with a cable length of 5 meters has the article number

303.000.0045. In the delivery condition, the sensor opens the contacts when the float

rises. With this property you can identify a broken cable as a leak. The type of the

connected sensor must be specified in the configuration menu.

The sensor cable can be extended up to 50 meters. The polarity of the connection does

not matter.

Climate sensor connection

Digital sensor system "Klima-2" (temperature and air humidity)

The climate sensor (Art. No. 3110000068) is connected to terminals 10, 11, 12

and 13. When connecting, observe the color coding of the sensor cables. If

necessary, the cable can be extended up to 30 m with a 4-core cable (cross-

section min. 0.5 mm²). Due to possible interference, do not lay the sensor cable

near power cables. The sensor must be protected from splash water.

Connecting to LAN

The control unit has a LAN connection (Ethernet, RJ45). The device is controlled and configured

exclusively via the LAN network with the PC-45 exclusiv, an external smart touch panel, a

computer or smartphone.

A standard network cable (patch cable, CAT5) must be used for the connection. Each device in a

network cluster (PC-45 exclusiv,Alarm-control.plus etc.) must be in the same local network. The

easiest way is to connect all devices to a network switch. Our product range includes a suitable

network switch named “Cluster-switch.plus”. For more information, see the "Connect to a

Computer Network and the Internet" section.

white

brown.

green.

yellow.

digital

sensor

system

«Klima-2»

Installation and operating manual for Alarm-control.plus page 5 (10)

Connection to the pool control PC-45 exclusiv

With the PC-45 exclusiv, several devices of the Plus series can be combined into a single network

cluster for pool management. Data is exchanged between devices via a local computer network

(LAN) and using its own communication protocol based on the UDP protocol.

To connect devices, both devices must be connected to the local network.

Connection to a “Smart-Touch” operating panel

To connect the devices with each other, both devices must be connected to the local network. On

the screen of the external Smart-Touch control panel, go to the “Add OSF device” menu and

select the “Alarm-control.plus” block. Then press the start button and then the LAN button in the

Alarm-control.plus according to the instructions displayed. For more information, see the

instructions for the external smart touch control panel.

Please also note the installation and operating instructions for the devices PC-45 exclusiv and

external smart touch control panel.

LAN cable

12V

Installation and operating manual for Alarm-control.plus page 6 (10)

Setup and configuration

The configuration and setting of the Alarm-control.plus device can be done via the screen of the

PC-45 exclusiv, from the computer or smartphone.

Configuration from the PC-45 exclusiv

After the two controls have been connected, an additional

symbol appears in the main menu of the PC-45 exclusiv.

Clicking this button takes you to the configuration menu.

Alarm-control.plus menu

The screen shows the current status of the sensors

connected to the Alarm-control.plus.

Attention! The connected sensors are configured on the

Alarm-control.plus website Set alarm limits

for air temperature and humidity

Alarm settings for water sensors

On this screen you can individually set the reaction of the

Alarm-control.plus-unit when a water sensor is triggered.

There are 5 ways to respond to a leak:

Audible alarm.

Potential-free contact of the alarm relay. The relay

closes for the duration of the leak.

230V relay for valve control. The relay closes for

the duration of the leak.

Stopping the PC-45 exclusive and all devices

contained in its network cluster.

Send alarm by email. The email address is set via the

Alarm-control.plus website.

□Deactivating the response to the leakage sensor.

Alarm settings for climate sensor

On this screen you can set the reaction of the Alarm-

control.plus individually for each parameter that exceeds

the set limit values. There are three ways to react to an

alarming event:

Audible alarm.

Potential-free contact of the alarm relay.

Send alarm by email.

□Disabling the response to the event.

Installation and operating manual for Alarm-control.plus page 7 (10)

Connect to a computer network and the Internet

The Alarm-control.plus has a LAN connection (RJ-45, Ethernet) and supports

the Fast Ethernet protocol with a speed of up to 100 Mbit / s.

Below is a typical diagram for connection of the Cover-control.plus to a

computer network that enables access to the device parameters both from

the local network and via the global Internet.

A standard Ethernet network cable must be used for a connection. You can access the device

remotely via the existing connection.

Enter the device's IP address in an Internet browser to access it over the network. The IP address

can be read in the "Network OSF device cluster" menu.

If the local network has internet access and access to one of the communication servers, you

can easily organize remote access to the device from anywhere in the world via the internet.

Use of the communication server

The communication server provides plug and play internet access to the coverage control unit.

The Alarm-control.plus is permanently connected to the communication server

http://devices2.osf.de/.

When you visit the server for the first time, you will need to register and create a

personal account.

Each device has an individual ID number consisting of 6 characters (numbers

and letters). To get remote access to the device, you

need to enter and save the ID number in your profile. You can find the

number on the label attached to the device housing near the LAN port.

The device then appears in the device overview and can be operated via the

communication server.

To delete a device from the list of devices, simply delete its identification number from the profile

and click the update button.

Wi-Fi and Internet-

Router

Local network

Global network

Ser.No.:0 ID: xxxxxx

IP: 192.168.123.165

MAC: 00:50:c2:ee:0a:00

Installation and operating manual for Alarm-control.plus page 8 (10)

Webserver

The web server creates HTML pages for Alarm-control.plus and sends them to the internet

browser of a computer or smartphone on request.

The integrated web server enables remote monitoring of

the sensors from any computer or smartphone. Thanks to

the osf communication server, access from anywhere in

the world is very easy.

The web server has three levels of access:

overview page, user access, and service access.

About Alarm-control.plus

The page with information on the serial number and firmware number as well as the update option

can be accessed by pressing the "esc" button on the main screen. The update link is displayed if

the user has service access.

Alarm settings

for water sensors

On this screen you can individually set the reaction of the

Alarm-control.plus-unit when a water sensor is triggered.

There are 5 ways to respond to a leak:

Audible alarm.

Potential-free contact of the alarm relay. The relay

closes for the duration of the leak.

230V relay for valve control. The relay closes for the duration of the leak.

Stopping the PC-45 exclusive and all devices contained in its network cluster.

Send alarm by email.

Deactivating the response to the leakage sensor.

Alarm settings

for climate sensor

On this screen you can set the reaction of the Alarm-

control.plus individually for each parameter that exceeds

the set limit values. There are three ways to react to an

alarming event:

Audible alarm.

Potential-free contact of the alarm relay.

Send alarm by email.

Deactivating the response to the climate sensor.

Service settings

This menu can only be called up after the PIN code has

been entered successfully.

Time and date settings

In this menu you can set the current time and date

manually or automatically.

Settings for LAN network

In this menu you can enter an individual name for the Cover-control.plus, which will be displayed

in the header of the Internet browser and on the overview page of the communication server.

Installation and operating manual for Alarm-control.plus page 9 (10)

Duration of the alarm pause

This parameter determines how long the alarm pause lasts when you press the button on the

front of the Alarm-control.plus. After the pause time has elapsed, the device automatically returns

to the active mode. The button‘s illumination is blue during the pause.

The factory setting is 30 minutes. The maximum setting is 180 minutes.

Event log

The event log shows in text form all events and changes that have recently been made.

Climate sensor configuration

If a climate sensor is used, on this page you can:

- Correct the displayed values of the measured

temperature and humidity values.

- Set the alarm limits of climate measurements

Configuration of the water sensors

The water sensors are configured in this menu. The

following settings are possible:

- Assigning individual names for the sensors

- Selecting sensor type: pair of electrodes or float switch.

- Activation or deactivation of the alarm message of the

sensor in the event of leaks.

- To determine whether the respective sensor is present

Fuses

The following fuse is located on the motherboard:

A 0.25 A fuse protects the climate sensor connection

Factory setting

All parameters are reset to the factory setting by

pressing and holding the button next to the LAN

connection for ten seconds.

The following are the factory settings for important parameters required for a successful

connection of the device to a computer network:

IP address automatically (DHCP server) - yes.

Automatic internet time - yes.

Time zone - GMT + 1. (Central Europe). The required time zone must be set manually for correct

operation.

PIN for user access –1234

PIN for service access –5678

Resetting to the factory settings does not reset the statistical information on the operating hours.

All operational logs remain unchanged.

Installation and operating manual for Alarm-control.plus page 10 (10)

Wiring diagram

Further information can be found on the Internet at the following address:

https://osf.de/download/documents/documents.php?device=Alarm-control-plus

We wish you a lot of fun and relaxation in your swimming pool

Subject to changes Januar 2021

water sensor

with 2

immersion

electrodes

Alarm-Control.plus

mains

1/N/PE

230V 50Hz

Up to 6 water sensors of different types:

LAN socket

LAN button

white

brown.

green.

yellow.

sensor system

«Klima-2»

ALARM

signal contact

potential-free

max. 8А

motor-

valve

230V

max. 4А

Mini-

float switch

open

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere OSF Steuerungssystem Handbücher

OSF

OSF Pool control PC-400-ES Bedienungsanleitung

Beliebte Steuerungssystem Handbücher anderer Marken

Pentair Pool Products

Pentair Pool Products Compool Bedienungsanleitung

ComfortNET

ComfortNET CTK04 Bedienungsanleitung

Fireye

Fireye InSight II 95DSS3 Bedienungsanleitung

CAME

CAME G3000 Bedienungsanleitung

Idemia

Idemia MorphoAccess VP MD Bedienungsanleitung

Axis

Axis P1445-LE-3 Bedienungsanleitung

HEIDENHAIN

HEIDENHAIN TNC 150 B Bedienungsanleitung

CNC-Step

CNC-Step High-Z T-Series Bedienungsanleitung

Doosan

Doosan DVF Series Bedienungsanleitung

Honeywell

Honeywell KAP 140 Bedienungsanleitung

Honeywell

Honeywell vk41 series Bedienungsanleitung

AirBench

AirBench FPW Installationsanleitung

Cypress

Cypress HHR-3160 Bedienungsanleitung

CAME

CAME GLT40AOS Bedienungsanleitung

Zonex

Zonex GEN II -VVT Benutzerhandbuch

Altronics

Altronics K 9650 Bedienungsanleitung

micro-trak

micro-trak RoadMaster Bedienungsanleitung

micro-trak

micro-trak Calc-An-Acre II Bedienungsanleitung