Osram Traxon ecue ARCHISHAPE 2.0 Dot S Bedienungsanleitung

ARCHISHAPE®2.0 Dot S/M/L

INSTALLATION GUIDE

V1.0

Cover:

ARCHISHAPE®2.0 Dot S/M/L (ETL)

www.traxontechnologies.com | www.osram.us/traxon

PENDING. SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE.

Installation Guide 01/22 V1.0 2 of 20

Content

1. Safety And Operation 3

2. Introduction 4

3. Installation 9

4. System Configuration 15

5. Care and Maintenance 17

6. Technical Specification 18

7. Troubleshooting 19

8. Warranty Statement 19

For your own safety and that of the product, please read this installation guide carefully before

beginning setup and installation.

www.traxontechnologies.com | www.osram.us/traxon

PENDING. SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE.

Installation Guide 01/22 V1.0 3 of 20

1. Safety And Operation

1. CAUTION - Unplug the power supply from the mains power before connecting or disconnecting any cables

as this can damage the products.

2. CAUTION - Avoid looking directly into the LED light source at close range for your own safety.

3. Persons installing this product should make sure:

a. The installation complies with all applicable codes, state and local laws, ordinances, standards

and safety regulations.

b. The installation environment is carefully studied and suitable surge protection measure(s) is

taken.

c. He or she is qualiﬁed for the handling of electrical equipment.

4. Do not attempt to install or use the product until installation instructions and safety labels are fully understood.

This product is designed for indoor and outdoor use.

5. Ensure product operates within the speciﬁed temperature range. (Refer to 6. TECHNICAL SPECIFICATION for

more details.)

6. Do not attempt to open the product. Not user serviceable.

7. Do not use the product if any part of it, or the power cables are damaged.

8. Only use product for speciﬁed voltage, do not exceed. (Refer to 6. TECHNICAL SPECIFICATION for more

details.)

9. Always maintain connection to ensure waterprooﬁng.

10. If the product has been subjected to drastic temperature variances, for example, following transportation, do

not connect the ﬁxture until it has reached room temperature, as moisture condensation may cause electric

shock and product damages.

11. When installing the products and system power supplies, please ensure they will not be exposed to moisture

and extreme heat (and direct sunlight for outdoor products). Besides, keep a clean operating environment for

the ﬁxtures and system power supplies.

12. Please study this Installation Guide thoroughly and check the latest Technical Speciﬁcation Sheets available

from the Traxon website www.osram.us/traxon before setup.

13. Any non-compliance of the Installation Guide will void the Traxon warranty.

Please read through Safety and Operation before start of the installation.

www.traxontechnologies.com | www.osram.us/traxon

PENDING. SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE.

Installation Guide 01/22 V1.0 4 of 20

2. Introduction

2.1 General

ARCHISHAPE®2.0 Dot is a high-brightness, fully customizable media dot solution available in S, M or L with Clear or

Diffused View lens to meet your project specifications. Each Dot is individually-addressable making ARCHISHAPE®

2.0 Dot a durable, scalable solution for vivid accents, graphics and video playback in installations of any size and

complexity.

Features:

— DMX512 Control

— Daisy Chain System

— Auto-Addressing with optional accessory & e:cue Controls

— IP66; IK09; ANSI 3G

— Suitable for irregular surfaces, planes, and conﬁgurations

www.traxontechnologies.com | www.osram.us/traxon

PENDING. SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE.

Installation Guide 01/22 V1.0 5 of 20

2.2 Dimensions

FIG.1: ARCHISHAPE®2.0 Dot S/M/L

AS 2.0 Dot S AS 2.0 Dot M AS 2.0 Dot L

Clear View

14.4mm/0.57”

38.4mm/1.51”

AS 2.0 Dot S AS 2.0 Dot M AS 2.0 Dot L

Diffused View

10mm/0.39”

29.3mm/1.15”

14.3mm/0.56”

10mm/0.39”

29.3mm/1.15”

14.5mm/0.57”

35.5mm/1.40”

53mm/2.09”

26mm/1.02”

19mm/0.75”

12mm/0.47”

12mm/

0.47”

52.2mm/2.06”

41mm/1.61”

40mm/1.57”

φ68mm/2.68”

4 x φ3.3mm/0.13”

12mm/

0.47”

55mm/2.17”

41mm/1.61”

4 x φ3.3mm/0.13”

φ71mm/2.80”

45mm/1.77”

19mm/0.75”

53mm/2.09”

26mm/1.02”

12mm/0.47”

4 x φ3.3mm/0.13”

41mm/1.61”

40mm/1.57”

φ68mm/2.68”

12mm/

0.47”

52.2mm/2.06”

4 x φ3.3mm/0.13”

φ71mm/2.80”

41mm/1.61”

45mm/1.77”

12mm/

0.47”

55mm/2.17”

19.6mm/0.77”

25.5mm/1.00”

3.2mm/0.13” 3.2mm/0.13” 3.2mm/0.13”

19.5mm/0.77”

3.4mm/0.53”

3.2mm/0.13” 3.2mm/0.13”

3.2mm/0.13”

Mounting bracket

∅∅

www.traxontechnologies.com | www.osram.us/traxon

PENDING. SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE.

Installation Guide 01/22 V1.0 6 of 20

FIG.2: ARCHISHAPE®2.0 Dot S/M/L Accessories

AS Dot End Cap with Resistor (

AM345880055

)

Starter Cable 16ft / 5m (

AM345860055

)

500mm (19.69")

47.2mm (1.86")

∅18mm (0.71")

12mm (0.47")

RED (1.0mm²)

GREEN (0.25mm²)

YELLOW (0.25mm²)

BLUE (0.25mm²)

BLACK (1.0mm²)

FEMALE CONNECTOR

30mm (1.18")

∅17.1mm (0.67")

∅15.6mm (0.61")

Interconnection Cable (

AM460720055

)

FEMALE CONNECTOR FEMALE CONNECTOR

∅18mm (0.71")

47.2mm (1.86") 1000mm (3.28') 47.2mm (1.86")

12mm (0.47")

18mm (0.71")

AS Dot S Mounting Clip (

AM357440055

)

19mm (0.75")

29.3mm (1.16")

10mm (0.39")

∅1.9mm (0.08”)

∅3.6mm (0.14")

Auto-addressing module (4ch AM345890055) (3ch AM456250055)

4X 5mm (0.20”)

∅

67.5mm (2.66")

61.5mm [2.42"]

∅106.5mm (4.19")

∅18mm (0.71")

48mm (1.89")

170mm (6.69")

18mm (0.709")

MALE CONNECTOR FEMALE CONNECTOR

RJ45 Power Injector Cable Kit (

AM357480055

)

42.8mm (1.69")

M17*1.0

∅19.6mm (0.77")

∅12mm (0.47")

300mm ± 20mm (11.81"± 0.79")

59.2mm (2.33")

∅18mm (0.71")

∅6.0mm (0.24")

∅7.2mm (0.28")

48mm (1.89")

150mm±10mm (5.91" ± 0.39")

22mm (0.87")

47mm (1.85")

18mm (0.71")

48mm (1.89") 39mm (1.54")

MALE CONNECTOR

TIGHTENING TORQUES: 0.7~0.9N.m

∅∅

∅

FEMALE CONNECTOR

www.traxontechnologies.com | www.osram.us/traxon

PENDING. SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE.

Installation Guide 01/22 V1.0 7 of 20

∅∅∅∅

∅

∅"

∅

Power Injector Cable Kit (

AM460710055

)

45.5mm (1.79")

∅∅

∅

∅7.2mm (0.28")

TIGHTENING TORQUES: 0.7~0.9N.m

18mm (0.71")

∅12mm (0.47")

17.7mm (0.70") 22mm (0.87")

59.2mm (2.33")

∅18mm (0.71")

MALE CONNECTOR

FEMALE CONNECTOR

300mm ± 20mm (11.81"± 0.79")

47mm (1.85")

150mm±10mm (5.91" ± 0.39")

48mm (1.89")

FIG.3: ARCHISHAPE®2.0 Dot S/M/L String

FEMALE CONNECTORMALE CONNECTOR

150mm (5.91")

47.2mm (1.86")

∅

18mm (0.71")

∅

18mm (0.71")

500mm (19.69")

48mm (1.89")

12mm (0.47")

FEMALE CONNECTORMALE CONNECTOR

150mm (5.91")

47.2mm (1.86")

∅18mm (0.71")

∅

18mm (0.71")

500mm (19.69")

48mm (1.89")

12mm (0.47")

www.traxontechnologies.com | www.osram.us/traxon

PENDING. SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE.

Installation Guide 01/22 V1.0 8 of 20

2.3 Packing Contents

FIG.4: ARCHISHAPE®2.0 Dot S/M/L Packing Contents

ARCHISHAPE®2.0 Dot S/M/L

FIG.5: RJ45 Power Injector Cable Kit Contents

RJ45 Power Injector Cable Kit

www.traxontechnologies.com | www.osram.us/traxon

PENDING. SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE.

Installation Guide 01/22 V1.0 9 of 20

3. Installation

3.1 Points To Consider

Plan your installation before mounting any luminaires. The following should be considered for a successful

installation.

— Weather conditions and ambient temperature of installation site.

— Appropriate cable lengths

— Adequate space for heat dissipation (150mm / 6” apart) of LED Engines (see “3.3 On-Site Installation” on page

12).

— Appropriate anchor bolts where necessary to secure the ARCHISHAPE®2.0 Dot S/M/L.

— The number of ARCHISHAPE®2.0 Dot S/M/L and LED Engines.

— Controller to be used to control the ARCHISHAPE®2.0 Dot S/M/L.

3.2 Pre-Installation Checks

3.2.1 Installation Checklist

1. Prepare cables and all necessary accessories.

2. Perform functional check of ARCHISHAPE®2.0 Dot S/M/L.

3. Ensure the connector of last dot is covered by the End Cap Resistor.

4. Ensure all pre-installation checks laid out below have been followed.

5. Mount the ARCHISHAPE®2.0 Dot S/M/L on-site. If the installation is to be left uncompleted overnight, place

all non-connected LED Engines and ARCHISHAPE®2.0 Dot S/M/L in an indoor environment.

Ensure all the Connection Cables, ARCHISHAPE®2.0 Dot S/M/L are initially stored in a dry area to guarantee the

complete sealing of the system from water before installation.

Connector should be properly connected with cable connectors and the connector of last dot should be covered

by its Waterproof End Cap to ensure IP66 rating.

3.2.2 Handling The ARCHISHAPE®2.0 Dot S/M/L String

When transporting or preparing the ARCHISHAPE®2.0 Dot S/M/L string, please handle with care. To reduce

stress on cables, carry by the ARCHISHAPE®2.0 Dot S/M/Ls and not the cable during transit.

FIG.6: Correct way of handling ARCHISHAPE®2.0 Dot S/M/L String

Allow slack on cable to

reduce stress

www.traxontechnologies.com | www.osram.us/traxon

PENDING. SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE.

Installation Guide 01/22 V1.0 10 of 20

3.2.3 Requirements Of Cable Bending And Twisting

Please take EXTRA precautions before bending or twisting ARCHISHAPE®2.0 Dot S/M/L cable. Lead Cable must

NOT be bent below the Minimum Bending Radius (4x Cable Diameter) and the Non-Bendable Length of 50mm /

2” near the connector end or near the cable overmold MUST be adhered to.

FIG.7: Minimum Cable Bending and Non-Bendable Length Requirement

(Non-Bendable Length)

500mm (19.69")

≥

(Minimum Bending Radius)

14mm/0.55”

20mm/0.79”

Ø7mm/0.28”

50mm/1.97”

(Minimum Bending Radius)

28mm/1.00”

≥

The ﬂat ARCHISHAPE®2.0 Dot S/M/L Cable must NOT be bent/twisted below 20mm (0.79”) from edge of

ARCHISHAPE®2.0 Dot S/M/L housing (Non-Bendable/Non-Twistable Length).

Twisting the ﬂat cable is NOT recommended. If twisting is necessary for installation, please adhere to the Non-

Twistable Length speciﬁed in Fig. 6 and ensure the mounting pitch is greater than or equal to 75% of the normal

ARCHISHAPE®2.0 Dot S/M/L to ARCHISHAPE®2.0 Dot S/M/L pitch. The middle part of the cable must be

secured to the mounting surface with a cable tie (see “3.3 On-Site Installation” on page 12 and FIG.11 on page

14). Ensure no damage is generated on the cable.

FIG.8: Minimum Clearance

20mm/0.79”

Minimum clearance

from dot

Non-Bendable/

Non-Twistable Length

NOTE: Water ingress incurred due to excess cable bending/twisting will not be warrantied by Traxon Technologies.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Osram Beleuchtungsausrüstung Handbücher

Osram

Osram 44X10W Bedienungsanleitung

Osram

Osram 4920Z Bedienungsanleitung

Osram

Osram Inventronics DALI COUPLER LS HIGHBAY G2 Bedienungsanleitung

Osram

Osram LEDinspect SLIMLINE 250 LEDIL206 Bedienungsanleitung

Osram

Osram OTi30W Leitfaden

Osram

Osram Clay Paky ALPHA SPOT 300 Bedienungsanleitung

Osram

Osram LEDinspect Bedienungsanleitung

Osram

Osram ARCHISHAPE Media Tube Bedienungsanleitung

Osram

Osram DALI PCU Bedienungsanleitung

Osram

Osram Claypaky SHARPY X FRAME Bedienungsanleitung

Osram

Osram LEDinspect PRO SLIMLINE 280 Bedienungsanleitung

Osram

Osram Clay Paky ALPHA PROFILE 1500 Bedienungsanleitung

Osram

Osram Claypaky XTYLOS Bedienungsanleitung

Osram

Osram ZELION HL300 Grow Light Bedienungsanleitung

Osram

Osram Traxon e:cue ProPoint Kontour Narrow RGB Bedienungsanleitung

Osram

Osram ARAY CTFI1100SARAY-G1-FS927-05-1L-50 Bedienungsanleitung

Osram

Osram BY-P28 Bedienungsanleitung

Osram

Osram 3240G4 Bedienungsanleitung

Osram

Osram PermaLED® Area Light Medium Bedienungsanleitung

Osram

Osram SubstiTUBE T8 HF Bedienungsanleitung

Osram

Osram BY-M46 Bedienungsanleitung

Osram

Osram ADB Stagelight LEXPERT PROFILE L Bedienungsanleitung

Osram

Osram Traxon e:cue Allegro Media Tube Lite Bedienungsanleitung

Osram

Osram KREIOS SL Bedienungsanleitung

Beliebte Beleuchtungsausrüstung Handbücher anderer Marken

Brizo

Brizo 8SP-MU-4 Bedienungsanleitung

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Bedienungsanleitung

IKEA

IKEA BJÖRKSPIREA Bedienungsanleitung

Laserworld

Laserworld Evolution Series ES-400RGB Bedienungsanleitung

EuroLite

EuroLite LED B-40 Bedienungsanleitung

Qazqa

Qazqa Suplux SL 3 Black 103062 Bedienungsanleitung

Commercial Electric

Commercial Electric 54568141 Bedienungsanleitung

CREE LIGHTING

CREE LIGHTING 304 Series Bedienungsanleitung

Goobay

Goobay 49867 Bedienungsanleitung

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Bedienungsanleitung

Alkalite

Alkalite Krypton KT-81 Bedienungsanleitung

Clas Ohlson

Clas Ohlson GU10 Bedienungsanleitung

DTS

DTS DELTA 10 F Bedienungsanleitung

ring

ring Solar Steplight Bedienungsanleitung

One Stop Gardens

One Stop Gardens 57696 Montageanleitung

SIREM

SIREM Swimeo A2 Bedienungsanleitung

Silvair

Silvair MESH-CEDRP Bedienungsanleitung

S&P

S&P PCRL80 Bedienungsanleitung

Osram traxon ecue ARCHISHAPE 2.0 Dot S Bedienungsanleitung

Beliebte Beleuchtungsausrüstung Handbücher anderer Marken