Osram Traxon e:cue Allegro Media Tube Lite Bedienungsanleitung

Allegro Media Tube®Lite

INSTALLATION GUIDE

V1.0

Cover:

Allegro Media Tube®Lite RGBW

Allegro Media Tube®Lite RGB

Allegro Media Tube®Lite DW

www.traxontechnologies.com | www.osram.us/traxon

PENDING. SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE.

Installation Guide V1.0 12/21 P. 2 of 20

CONTENT

1. Safety And Operation 3

2. Introduction 4

3. Installation 7

4. System Configuration 11

5. Care and Maintenance 16

6. Troubleshooting 17

7. Technical Specification 18

8. Warranty Statement 19

For your own safety and that of the product, please read this installation guide

carefully before beginning setup and installation.

www.traxontechnologies.com | www.osram.us/traxon

PENDING. SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE.

Installation Guide V1.0 12/21 P. 3 of 20

1. Safety And Operation

— CAUTION - Unplug the power supply from the mains power before connecting any cables as this can damage

the products.

— CAUTION - Avoid looking directly into the LED light source at close range for your own safety.

— Persons installing this product should make sure:

1. The installation complies with all applicable codes, state and local laws, ordinances, standards and

safety regulations.

2. The installation environment is carefully studied and suitable surge protection measure(s) is taken.

3. He or she is qualiﬁed for the handling of electrical equipment.

— Do not attempt to install or use the product until installation instructions and safety labels are fully understood.

This product is designed for indoor and outdoor use.

— Ensure product operates within the speciﬁed temperature range. (Refer to 7. TECHNICAL SPECIFICATION for

more details.)

— The Allegro Media Tube®Lite does not contain any user-serviceable parts. Opening of the luminaire will void

the warranty.

— Do not use the product if any part of it, or the power cables are damaged.

— Only use product for speciﬁed voltage, do not exceed. (Refer to 7. TECHNICAL SPECIFICATION for more

details.)

— Always maintain connection to ensure waterprooﬁng.

— If the product has been subjected to drastic temperature variances, for example, following transportation, do

not connect the ﬁxture until it has reached room temperature, as moisture condensation may cause electric

shock and product damage.

— When installing the products and system power supplies, please ensure they will not be exposed to moisture

and extreme heat (and direct sunlight for outdoor products). Keep a clean operating environment for the ﬁxtures

and system power supplies.

— Please study this Installation Guide thoroughly and check the latest Technical Speciﬁcation Sheets available

from the Traxon website www.traxontechnologies.com and www.osram.us/traxon before setup.

— Any non-compliance of the Installation Guide will void the Traxon warranty.

www.traxontechnologies.com | www.osram.us/traxon

PENDING. SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE.

Installation Guide V1.0 12/21 P. 4 of 20

2. Introduction

2.1 General

Allegro Media Tube®Lite Diffused View Length Maximum number of pixels (PXL)

AL MT LT RGBW 300 3PXL DF R ETL 300mm / 11.8” 3

AL MT LT RGBW 1200 12PXL DF R ETL 1200mm / 47.2” 12

AL MT LT RGB 300 3PXL DF R ETL 300mm / 11.8” 3

AL MT LT RGB 1200 12PXL DF R ETL 1200mm / 47.2” 12

AL MT LT DW 300 3PXL DF R ETL 300mm / 11.8” 3

AL MT LT DW 1200 12PXL DF R ETL 1200mm / 47.2” 12

Allegro Media Tube®Lite Direct View Length Maximum number of pixels (PXL)

AL MT LT RGBW 300 3PXL CR ETL 300mm / 11.8” 3

AL MT LT RGBW 1200 12PXL CR ETL 1200mm / 47.2” 12

AL MT LT RGB 300 3PXL CR ETL 300mm / 11.8” 3

AL MT LT RGB 1200 12PXL CR ETL 1200mm / 47.2” 12

AL MT LT DW 300 3PXL CR ETL 300mm / 11.8” 3

AL MT LT DW 1200 12PXL CR ETL 1200mm / 47.2” 12

Allegro Media Tube®Lite is a slim, direct view luminaire designed to integrate into any wall, facade or media lighting

application with tight installation requirements. Available with a Direct View or Diffused View lens and 3 pixels per foot,

Allegro Media Tube Lite provides smooth effects to add life and motion to the installation. Featuring auto addressing

and simple quick-lock connections, Allegro Media Tube Lite is perfect for building façades, media applications, and

more.

Features:

— Available lengths: 300mm / 1ft (3PXL), 1200mm / 4ft (12PXL)

— Diffused view and direct view

— Three color options: RGBW, RGB, DW (2700K - 6500K)

— DMX512

— Daisy Chain System with quick lock connectors

— Auto-addressing

— Outdoor Applications, Suitable for Coastal Environment (IP66 and IK09 rated)*

*IK09 is for diffused view

www.traxontechnologies.com | www.osram.us/traxon

PENDING. SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE.

Installation Guide V1.0 12/21 P. 5 of 20

2.2 Dimensions

FIG.1: Allegro Media Tube®Lite Direct View

A D

L1 L2

FIG.2: Allegro Media Tube®Lite Diffused View

A D

L1 L2

NOTE: Please see CAD ﬁles for additional dimensional data.

W1 W2 H1 H2 A D L L1 L2

1200mm

48”

24.5mm

0.96”

33.3mm

1.31”

58.2mm

2.29”

31.2mm

1.23”

240mm

9.45”

850mm

33.46”

1200mm

47.24”

116.5mm

4.59”

136.3mm

5.37”

300mm

12”

24.5mm

0.96”

33.3mm

1.31”

58.2mm

2.29”

31.2mm

1.23”

145mm

5.71”

135mm

5.31”

300mm

11.81”

116.5mm

4.59”

136.3mm

5.37”

NOTE: Please see CAD ﬁles for additional dimensional data.

W1 W2 H1 H2 A D L L1 L2

1200mm

48”

24.5mm

0.96”

33.3mm

1.31”

70mm

2.76”

43mm

1.69”

240mm

9.45”

850mm

33.46”

1200mm

47.24”

116.5mm

4.59”

136.3mm

5.37”

300mm

12”

24.5mm

0.96”

33.3mm

1.31”

70mm

2.76”

43mm

1.69”

145mm

5.71”

135mm

5.31”

300mm

11.81”

116.5mm

4.59”

136.3mm

5.37”

www.traxontechnologies.com | www.osram.us/traxon

PENDING. SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE.

Installation Guide V1.0 12/21 P. 6 of 20

FIG.3: Allegro Media Tube®Lite Accessories

End Cap with 120 Ohm Terminator

Starter Cable

Interconnection Cable

End Cap with 120 Ohm Terminator

Starter Cable

Interconnection Cable

End Cap with 120 Ohm Terminator

Starter Cable

Interconnection Cable

1m, 5m, 30m / 3.28’, 16.40’, 98.43”

0.14m, 1m, 4m / 0.46’, 3.28’, 13.12’

56.3mm / 2.22”

2*18AWG+4*24AWG

Round Cable

22.5mm / 0.89” 22.5mm / 0.89” 20.3mm / 0.80”

20.3mm

2*18AWG+4*24AWG

Round Cable

φ7mm / 0.28”

Wire# Description Color

1DMX+ Green

2Ground White

3DMX− Blue

4DC48V− Black

5DC48V+ Red

6Address Brown

Connector Pin Assignment

Input Output

2.3 Packing Contents

FIG.4: Packing Contents

Allegro Media Tube®Lite Direct/Diffused View x 1

Mounting bracket x 2

www.traxontechnologies.com | www.osram.us/traxon

PENDING. SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE.

Installation Guide V1.0 12/21 P. 7 of 20

3. Installation

3.1 Points To Consider

Plan your installation before mounting the Allegro Media Tube®Lite. The following should be considered for a

successful installation.

— Weather conditions and ambient temperature of installation site.

— Appropriate cable lengths (cable gauges described in system diagram). Please consult your local Traxon ofﬁce

or authorized agent for necessary aid.

— The number of the Allegro Media Tube®Lite and appropriate LED Engines.

— DMX512 to be used to control the Allegro Media Tube®Lite.

— Distance between each Tube for thermal expansion and maintaining pixel pitch.

— Mounting distances should be considered.

— Proper surge protection.

FIG.5: Allegro Media Tube®Lite Cable System

Starter Cable

From terminal block to ﬁrst Allegro Media Tube Lite in chain

Interconnection Cable

From Allegro Media Tube Lite to another Allegro Media Tube Lite

End Cap with 120Ω Terminator

The end cap includes DMX data terminator

End Cap with 120 Ohm Terminator

Starter Cable

Interconnection Cable

1m, 5m, 30m / 3.28’, 16.40’, 98.43”

2*18AWG+4*24AWG

Round Cable

20.3mm / 0.80”

φ7mm / 0.28”

End Cap with 120 Ohm Terminator

Starter Cable

Interconnection Cable

0.14m, 1m, 4m / 0.46’, 3.28’, 13.12’

22.5mm / 0.89”

20.3mm

2*18AWG+4*24AWG

Round Cable

φ7mm / 0.28”

End Cap with 120 Ohm Terminator

Starter Cable

Interconnection Cable

56.3mm / 2.22”

22.5mm / 0.89”

www.traxontechnologies.com | www.osram.us/traxon

PENDING. SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE.

Installation Guide V1.0 12/21 P. 8 of 20

3.2 Pre-Installation Checks

3.2.1 Installation Checklist

1. Prepare cables and all necessary accessories (Waterproof Quick Lock End Caps etc).

2. Perform functional check of the Allegro Media Tube®Lite. Take care not to damage cables/connectors during

pre-installation checks.

3. Ensure all pre-installation checks laid out below have been followed.

4. Mount the Allegro Media Tube®Lite on-site. If the installation is to be left uncompleted overnight, place all

non-connected LED Engines and the Allegro Media Tube®Lite in an indoor environment.

5. All units must be connected or utilize end caps to protect from water ingress.

Ensure all the Interconnection Cables, Allegro Media Tube®Lite and LED Engines are initially stored in a dry area

to guarantee the complete sealing of the system from water before installation.

3.2.2 Mounting Bracket

Mounting hardware (screws, lock washers and washers) are required for mounting the bracket to the surface.

Mounting hardware by others. The mounting brackets can be moved along the extrusion to match installation

requirements.

FIG.6: Mounting Bracket

22.5mm/0.89”

Mounting Hardware

(by others)

Tighten screw

to lock bracket

in place

22.5mm/0.89”

Tighten screw

to lock bracket

in place

www.traxontechnologies.com | www.osram.us/traxon

PENDING. SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE.

Installation Guide V1.0 12/21 P. 9 of 20

3.2.3 Installation Sequence

1. Measure the correct distances for brackets and install the Allegro Media Tube®Lite ﬁxtures.

2. Connect the Allegro Media Tube®Lite in the daisy-chain manner outlined in the System Diagram to form large

installations.

3. Perform functional check on all the Allegro Media Tube®Lite and inspect cables and brackets for any

damage. Check for any abnormalities with the control signal.

4. Report any functional defect found to your nearest Traxon Technologies ofﬁce. DO NOT attempt to install the

Allegro Media Tube®Lite with functional defects on-site.

3.3 On-Site Installation

• DO NOT attempt installation in wet or severe weather conditions.

• DO NOT leave and expose any Allegro Media Tube®Lite or LED Engines

unconnected under wet/raining or snowing environment.

• IP failure induced by stressed/damaged cables during or after installation

will not be under warranty by Traxon Technologies.

• ALWAYS keep the cables protected from sharp objects and ensure no

damage is generated on the cable.

Failure to keep Allegro Media Tube®Lite within the operating temperature range of –40°C to +50°C / –40°F to

+122°F and storage temperature range of –40°C to +70°C / –40°F to +158°F will void the product’s warranty.

3.3.1 On-Site Installation

1. Fix brackets to installation surface with anchor bolts or screws (by others).

2. The Allegro Media Tube®Lite are interconnected using the IN and OUT cables/connectors on each end of

the tube. Connectors will make an audible “click” when connected. Gently pull on the cables in opposites

directions to ensure they are fully locked and do not come loose. The below diagram shows the Tube

connections. Always remember to afﬁx a Quick Lock Waterproof End Cap (sold separately) for the OUT

connector of the ﬁnal Tube in each daisy chain. See System Diagram for details.

FIG.7: Allegro Media Tube®Lite Connections

Starter Cable End Cap

NOTE: Any water ingress incurred due to improper installation of cable connectors or Waterproof Quick Lock

End Caps will not be covered under warranty by Traxon Technologies.

www.traxontechnologies.com | www.osram.us/traxon

PENDING. SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE.

Installation Guide V1.0 12/21 P. 10 of 20

3. Be sure not to compress the IN/OUT cables.

NOTE: To keep LED pitch consistent and allow for thermal expansion, be sure to keep a minimum distance of

4mm (0.16”) between consecutive Allegro Media Tube®Lite (see below diagram).

FIG.8: Keep minimum distance between fixtures

To maintain consistent LED pitch and to allow for thermal expansion, a minimum of

4mm / 0.16" is required between luminaire's. End Cap Seal on Last Tube

>4mm / 0.16"

4. The ﬁrst tube of the daisy-chain group has to be connected to the control system via Waterproof Junction

Box (by others).Starter cables, Data and Power cables, and video ﬁber optic cables have to be installed

through conduit.

5. Set up the control system indoors as detailed in the System Diagram and connect to the Allegro Media Tube®

Lite. Start each unit and verify correct function.

Andere Handbücher für Traxon e:cue Allegro Media Tube Lite

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Osram Beleuchtungsausrüstung Handbücher

Osram

Osram ARAY CTFI1100SARAY-G1-FS927-05-1L-50 Bedienungsanleitung

Osram

Osram BY-P09 Bedienungsanleitung

Osram

Osram Claypaky MINI XTYLOS HPE Bedienungsanleitung

Osram

Osram 3240G4 Bedienungsanleitung

Osram

Osram LUMINESTRA LED 8W Bedienungsanleitung

Osram

Osram LEDinspect Bedienungsanleitung

Osram

Osram LINEARlight FLEX Protect POWER Series Bedienungsanleitung

Osram

Osram Fluence VYPR 3p Fehlerbehebungshandbuch

Osram

Osram ARCHISHAPE Media Tube Bedienungsanleitung

Osram

Osram ARCHISHAPE 2.5 Washer Bedienungsanleitung

Osram

Osram LEDinspect PRO SLIMLINE 280 Bedienungsanleitung

Osram

Osram DALI PCU Bedienungsanleitung

Osram

Osram AirZing PRO 5030 UNIV Benutzerhandbuch

Osram

Osram Inventronics DALI COUPLER LS HIGHBAY G2 Bedienungsanleitung

Osram

Osram Claypaky MINI XTYLOS Bedienungsanleitung

Osram

Osram TW-DL-12V/110mA-Power Pack Bedienungsanleitung

Osram

Osram LEDinspect Slimline Bedienungsanleitung

Osram

Osram Traxon e:cue Allegro Media Tube Lite Installationsanleitung

Osram

Osram RGBWA+UVIR Slimpar Series Bedienungsanleitung

Osram

Osram ZELION HL300 Grow Light Bedienungsanleitung

Osram

Osram Clay Paky ALPHA SPOT 300 Bedienungsanleitung

Osram

Osram PermaLED® Area Light Medium Bedienungsanleitung

Osram

Osram SYNIOS P2720 Series Montage- und Bedienungsanleitung

Osram

Osram Clay Paky ALPHA PROFILE 1500 Bedienungsanleitung

Beliebte Beleuchtungsausrüstung Handbücher anderer Marken

Brizo

Brizo 8SP-MU-4 Bedienungsanleitung

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Bedienungsanleitung

IKEA

IKEA BJÖRKSPIREA Bedienungsanleitung

Laserworld

Laserworld Evolution Series ES-400RGB Bedienungsanleitung

EuroLite

EuroLite LED B-40 Bedienungsanleitung

Qazqa

Qazqa Suplux SL 3 Black 103062 Bedienungsanleitung

Commercial Electric

Commercial Electric 54568141 Bedienungsanleitung

CREE LIGHTING

CREE LIGHTING 304 Series Bedienungsanleitung

Goobay

Goobay 49867 Bedienungsanleitung

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Bedienungsanleitung

Alkalite

Alkalite Krypton KT-81 Bedienungsanleitung

Clas Ohlson

Clas Ohlson GU10 Bedienungsanleitung

DTS

DTS DELTA 10 F Bedienungsanleitung

ring

ring Solar Steplight Bedienungsanleitung

One Stop Gardens

One Stop Gardens 57696 Montageanleitung

SIREM

SIREM Swimeo A2 Bedienungsanleitung

Silvair

Silvair MESH-CEDRP Bedienungsanleitung

S&P

S&P PCRL80 Bedienungsanleitung