oventrop REGTRONIC PC Bedienungsanleitung
INSTRUCTIONS FOR
INSTALLERS
Oventrop
REGTRONIC PC
Important!
Please read the instructions carefully before installing and operating the unit!
Failure to do this can void product warranty!
Please keep the instructions in a safe place!
The unit described has been manufactured and inspected according to CE
regulations.
Instructions for installers REGTRONIC PC
Instructions for installers 136659383 2 1317ZB009-10B-E, Revised 03/2008
REGTRONIC PC
Parameters set using the System Settings menu should only be
configured or modified by installers or qualified technical
personnel. Setting the wrong parameters can compromise the
functionality of the control unit and solar system
Table of Contents:
1"SYSTEM SETTINGS" MENU“/ CHANGES TO THE SYSTEM ........................ 3
2USING A DATASTICK
®
...................................................................................... 4
2.1 F
ACTORY SETTINGS
........................................................................................ 4
2.1.1 Restoring factory settings......................................................................... 4
2.1.2 Saving/loading configuration parameters.................................................. 4
2.2 U
PDATING SYSTEM SOFTWARE
......................................................................... 4
Instructions for installers REGTRONIC PC
Instructions for installers 136659383 3 1317ZB009-10B-E, Revised 03/2008
REGTRONIC PC
1 "S
YSTEM
S
ETTINGS
"
MENU
“/
C
HANGES
TO THE SYSTEM
During normal operation, the "System
Settings" menu only displays
parameters and does not allow them to
be altered. This prevents accidental
changes. To change parameters, this
menu must be selected within one
minute of switching on the unit.
While the system is running, changes
can be made using the System
Settings menu by pressing the top
, bottom and right-hand
button simultaneously.
Once the user is in the menu, no time
limits apply.
The System Settings menu "locks"
itself automatically one minute after
the unit has been switched on and
one minute after the user has exited
the menu.
The System Settings menu is used to
select the basic schema and the
language, and also to activate or
deactivate the available protective and
ancillary features. The buttons
and are used to page through
the various submenus. The status –
e.g. "On" or "Off" – is also shown next
to the name of each submenu.
Submenus are selected by using the
button.
Allocation of layout no. to system number: PC0 = 3330, PC1 = 3331, PC2 = 3332,
PC3=3333, PC4=3334
Note:: 3300 is the initial software set!
Example: change system from 3300 to 3331
System sel.
[off]
off
System
3300
on
off ok
ok
3300 3301 ok
ok
Service
[off]
MultiReg3
[off]
Instructions for installers REGTRONIC PC
Instructions for installers 136659383 4 1317ZB009-10B-E, Revised 03/2008
REGTRONIC PC
2 U
SING A
D
ATA
S
TICK
®
An installer or technician can use a DataStick
®
for the following tasks:
Updating unit parameters
Saving/loading factory settings
Updating system software
2.1 Factory settings
Factory settings can be saved, loaded
or restored in the "System Settings"
menu.
This also makes it possible to transfer
configuration data from one control unit
to another, for example.
2.1.1 Restoring factory settings
Menu item "Factory settings":
•Off
•On: Restores the default factory settings
2.1.2 Saving/loading configuration parameters
Menu item "Factory settings" Parameters:
Only insert or remove the DataStick
®
at this menu. If the DataStick
®
has been
previously used as a programming stick, then other menus in the system will ask the
user if the software on the DataStick
®
should be loaded! Parameter backups on the
stick will not have this effect.
•Off
•Save
•Stick available: Message "OK"
-Stick unavailable: Message "OK" (the data will be sent, although it
cannot be stored)
•Load
-Stick available, system no. and system version on the stick match the
data in the control unit: Message "OK"
-Stick available, system no. on the stick matches the data in the control
unit, but the version is different: Message "Chk." par."
: the installer needs to check and verify the parameters.
-System no. does not match the system no. in the control unit: Message
"Error"
2.2 Updating system software
First, insert the DataStick. If the
DataStick contains a software package
that is valid for this unit, then the
screen will display "Copy DataStick
start?". Press the "OK" button twice to
confirm, and the copy process will
start. Once copying has finished, the
unit will ask you to remove the
DataStick. The control unit will then
reboot.
Andere Handbücher für REGTRONIC PC
1
Andere oventrop Controller Handbücher
oventrop
oventrop R-Tronic RT B Bedienungsanleitung
oventrop
oventrop Hydromat DP DN 25 Handbuch
oventrop
oventrop Unibox E RTL Bedienungsanleitung
oventrop
oventrop Aktor M ST/2P L Bedienungsanleitung
oventrop
oventrop DN 15 Bedienungsanleitung
oventrop
oventrop Unibox RTL Bedienungsanleitung
oventrop
oventrop Hycocon DTZ Bedienungsanleitung
oventrop
oventrop REGTRONIC PX Gebrauchsanweisung
oventrop
oventrop NR 24 Bedienungsanleitung
oventrop
oventrop REGTRONIC PX Bedienungsanleitung
oventrop
oventrop Aktor M ST L Bedienungsanleitung
oventrop
oventrop Aktor M Handbuch
oventrop
oventrop EnOcean Aktor MH CON B Bedienungsanleitung
oventrop
oventrop Regtronic RD-W Bedienungsanleitung
oventrop
oventrop Aktor M ST Bedienungsanleitung
oventrop
oventrop Hydromat DFC Betriebsanleitung
oventrop
oventrop Regtronic BS/2-B Bedienungsanleitung
oventrop
oventrop Aktor M ST L Modbus Bedienungsanleitung
oventrop
oventrop NR 230 Bedienungsanleitung
oventrop
oventrop REGTRONIC PM Bedienungsanleitung
