Overland Storage ARCvault Series Leitfaden

This document describes how to do the following options:

•Replace existing drives in a drive bay with an LTO-4

SCSI or FC tape drive in an ARCvault loader or library.

•Add a new LTO-4 SCSI or FC tape drive in an empty

drive bay of an ARCvault 48 Library.

WARNING: To reduce the risk of electric shock or

damage to equipment, remove the power cord.

CAUTION: Adding a new tape drive results in a

reconfiguration of the library. In the ARCvault 48, it also

automatically disables any existing partitions.

IMPORTANT: When installing an LTO-4 drive into an

empty ARCvault 48 drive bay, an ARCvault Drive Bay

Upgrade Kit (available separately) is required. If two half-height

drives exist in a drive bay, both must be removed.

Unpacking

Carefully unpack and verify that you have all these parts:

•LTO-4 full height tape drive (SCSI or FC)

•Four M3x5 screws

•LVD SCSI cable, 2m (6.5 ft.) (SCSI add-on drive only)

•SCSI terminator (SCSI add-on drive only)

•These remove & replace instructions

Electrostatic Discharge Information

A discharge of static electricity can damage micro-circuitry

or static-sensitive devices. To help prevent Electrostatic

Discharge (ESD) damage, observe these and other

standard ESD precautions:

•Transport and store items in static-safe containers.

•Make sure you are always properly grounded.

•Avoid touching pins, leads, or circuitry.

Use this procedure to install a new LTO-4 full-height drive in a drive bay currently containing one or two drives. The new

drive replaces the existing drives. To install a drive in an empty drive bay, use the “New Drive Installation” on page 3.

Remove the Drive Assembly

1. To power down the unit from the Operator Control

Panel (OCP), press Power > Power Off Library >

OK (at the power down message).

2. After the unit has shut down, remove the power cord.

3. At the rear, remove either the SCSI cables and

terminator or FC cables from the appropriate drive

cover (Figure 1).

Figure 1. Drive Cover Assembly Locations and Cabling (2U and 4U)

ARCvault™Series

LTO-4 SCSI/FC Tape Drive

Add-On or Replace Instructions

Overview & Notes

ARC-0104

Existing Drive Replacement

ARC-0087

ARC-0075

SCSI CableTerminator

Power Cord

Thumbscrews

Power Cord

Thumbscrews

FC Cable

4. Loosen the two thumbscrews on the drive cover.

5. Remove the drive cover as follows:

a. Gently pull the drive cover out and hold it about

2 inches (5cm) below the drive bay (Figure 2).

b. Unplug the fan wiring from the fan connector.

c. For a SCSI drive assembly, using the guide handles,

pull the assembly out about 1 inch (2.5cm) and

unplug the SCSI cables from the drives.

d. Set the old drive cover aside.

Figure 2. SCSI Drive Assembly Cabling (2U SCSI)

6. Unplug the power and serial cables from the drive

assembly and position them off to the right.

7. Grasp the drive assembly guide grips and carefully

slide the assembly out of the unit.

Install the New Drive

1. Check the jumper pins on the new drive to confirm

they are at the default settings (ON-off-off-off-ON-ON).

2. Remove the drive assembly guides (Figure 3) located

on the sides of the assembly.

Figure 3. Remove Drive Assembly Guides (Single HH Drive)

3. Attach the drive guides to the sides of the new drive

(Figure 4) with four new M3x5mm screws.

Be sure the thicker guide is on the left side (when

looking at the front of the drive).

Figure 4. LTO-4 SCSI Drive Assembly (Rear View)

Reinstall the Drive Assembly

1. With the wiring positioned off to the right, slide the

drive assembly back into the drive bay.

For a SCSI drive assembly, leave the assembly sticking

out about 1 inch (2.5cm).

2. Attach black cable of the serial Y-cable to the drive

(Figure 5).

CAUTION: You MUST connect the BLACK serial

cable to the new LTO-4 drive for the unit to operate

correctly.

Figure 5. Attaching the Serial Y-Cable

3. Attach a power cable to the drive.

Continue with “Final Assembly and Test” on page 4.

ARC-0044

Serial Cables

Power Cables

Drive Cover Fan

Connector

SCSI Cable

Assembly

ARC-0106

Air Baffle

Drive Front

Screw Holes

Left Guide

Right Guide

Screw Holes

ARC-0017

Drive Guides

LTO-4 Drive

Screws

SerialPower

SCSI

Jumper Pins

ARC0143

Black to LTO-4 White (not used)

Power Cable

Use this procedure to install a new LTO-4 drive into an

empty drive bay on an ARCvault 48.

IMPORTANT: An ARCvault Drive Bay Upgrade Kit

(available separately) is required for this procedure. The

kit contains:

• 4-port drive cover assembly

• Left and right drive guides with four screws

• Serial Y-cable

• Air baffle with two screws (not used for this installation)

Remove the Drive Bay Baffle

1. From the Operator Control Panel (OCP), press Power

> Power Off Library > OK (at the power down

message) to power down the unit.

2. After the unit has shut down, remove the power cord.

3. Using a Phillips screwdriver, remove the two screws

holding the drive bay baffle (Figure 6).

Figure 6. ARCvault 48 Rear with Drive Bay Baffle

4. Remove the baffle and set it aside.

Install the New Drive

1. Check the jumper pins on the new drive to confirm

they are at the default settings (ON-off-off-off-ON-ON).

2. Attach the drive guides to the sides of the new drive

(Figure 7) with four new M3x5mm screws.

Be sure the thicker guide is on the left side (when

looking at the front of the drive).

Figure 7. LTO-4 SCSI Drive Assembly (Rear View)

Install the New Drive Assembly

1. With the wiring positioned off to the right, slide the

drive assembly back into the drive bay.

For a SCSI drive assembly, leave the assembly sticking

out about 1 inch (2.5cm).

2. Attach the main plug of the new serial Y-cable to the

serial cable going into the unit.

3. Attach the black cable of the Y-cable to the drive

(Figure 8).

CAUTION: You MUST connect the BLACK serial

cable to the new LTO-4 drive for the unit to operate

correctly.

Figure 8. Attaching the Serial Y-Cable

4. Attach the power cable to the drive.

Continue with “Final Assembly and Test” on page 4.

New Drive Installation

ARC-0077

Screws

SCSI Cables

Terminators

Baffle

Power Cord

ARC-0017

Drive Guides

LTO-4 Drive

Screws

SerialPower

SCSI

Jumper Pins

ARC-0144

Serial Y-Cable

Black to LTO-4

White (not used)

Unit Main

Serial Cable

Power Cable

IMPORTANT: For optimum performance of the library, it is

recommended that each drive be connected to the host

by a separate bus.

1. Install the drive cover as follows:

a. Holding the drive cover below the drive bay opening,

plug in the fan connector.

b. On a SCSI system, reattach the SCSI drive cables,

and slide the drive assembly the rest of the way

into the drive bay.

c. Carefully seat the drive cover and tighten the two

thumbscrews.

CAUTION: Be sure that all drive wiring is secure in

the space between the drive assembly and the

drive cover.

2. Reconnect the SCSI cables and terminator or FC

cables to the rear of the unit.

3. Plug in the power cord and power on the unit.

4. During POST, as soon as the reconfiguration message

appears, press OK.

5. After the library reboots, check the OCP Status to

verify that the unit recognizes the new drive.

All information contained in or disclosed by this document is considered proprietary by Overland Storage. By accepting this material, the recipient agrees that this material and the information contained therein are held in confidence and in trust and will not be

used, reproduced in whole or in part, nor its contents revealed to others, except to meet the purpose for which it was delivered. It is understood that no right is conveyed to reproduce or have reproduced any item herein disclosed without express permission from

Overland Storage. Overland Storage provides this document as is, without warranty of any kind, either expressed or implied, including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose. Overland Storage may make

improvements or changes in the product(s) or program(s) described in this document at any time. These changes will be incorporated in new editions of this publication.

Overland Storage assumes no responsibility for the accuracy, completeness, sufficiency, or usefulness of this document, nor for any problem that might arise from the use of the information in this document.

Final Assembly and Test

Additional Help

You can get additional technical support on the Internet at http://support.overlandstorage.com, or call

1-877-654-3429 (toll-free U.S. & Canada), +44 (0) 118-9898050 (Europe), or +1 (858) 571-5555 Option 5 (International).

Andere Handbücher für ARCvault Series

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Overland Storage Lagerung Handbücher

Overland Storage

Overland Storage NEO Series Bedienungsanleitung

Overland Storage

Overland Storage NEO 400S Bedienungsanleitung

Overland Storage

Overland Storage Snap Server 210 Bedienungsanleitung

Overland Storage

Overland Storage NEO Series Bedienungsanleitung

Overland Storage

Overland Storage E Series Bedienungsanleitung

Overland Storage

Overland Storage SnapSAN S1000 Bedienungsanleitung

Overland Storage

Overland Storage NEO 200S Bedienungsanleitung

Overland Storage

Overland Storage NEO 2000e Stücklistenhandbuch

Overland Storage

Overland Storage SnapServer DX2 Bedienungsanleitung

Overland Storage

Overland Storage ULTAMUS Handbuch

Overland Storage

Overland Storage NEO XL Series Bedienungsanleitung

Overland Storage

Overland Storage NEO 8000E Bedienungsanleitung

Overland Storage

Overland Storage SnapServer DX2 Bedienungsanleitung

Overland Storage

Overland Storage NEO 2000e Bedienungsanleitung

Overland Storage

Overland Storage REO 4600 Bedienungsanleitung

Overland Storage

Overland Storage SnapExpansion XSR Bedienungsanleitung

Overland Storage

Overland Storage NEO 8000E Bedienungsanleitung

Overland Storage

Overland Storage SnapServer XSD 40 Bedienungsanleitung

Overland Storage

Overland Storage SnapSAN S2000 Bedienungsanleitung

Overland Storage

Overland Storage SnapServer XSR 120 Bedienungsanleitung

Overland Storage

Overland Storage Neo Series 2000 Bedienungsanleitung

Overland Storage

Overland Storage SnapServer DX1 Bedienungsanleitung

Overland Storage

Overland Storage NEOs StorageLoader Bedienungsanleitung

Overland Storage

Overland Storage NEOs T24 Bedienungsanleitung

Beliebte Lagerung Handbücher anderer Marken

QNAP

QNAP TS 32PXU Series Bedienungsanleitung

LaCie

LaCie RUGGED RAID Bedienungsanleitung

Freecom

Freecom CLS DOCK Bedienungsanleitung

PNY

PNY Attache P-FD64MBATT3 Bedienungsanleitung

HP StorageWorks MSL2024 Bedienungsanleitung

OLT

OLT 6x6 Maximizer Bedienungsanleitung

Transcend

Transcend JetFlash 160 Bedienungsanleitung

LaCie

LaCie RUGGED MINI Bedienungsanleitung

Thunderbolt

Thunderbolt 600 Bedienungsanleitung

Panasonic

Panasonic LB-DH8 series Handbuch

Intel

Intel RAID High Availability Bedienungsanleitung

LaCie

LaCie 12big Thunderbolt 3 Bedienungsanleitung

Spectra Logic

Spectra Logic T-Series Spectra T50e Bedienungsanleitung

Panasonic

Panasonic LKM-F931-1 Bedienungsanleitung

Tabernus

Tabernus Enterprise Erase E2400 Bedienungsanleitung

Rocstor

Rocstor COMMANDER 3F series Bedienungsanleitung

HP P9000 Bedienungsanleitung

Western Digital

Western Digital Ultrastar Data60 Bedienungsanleitung