Overland Storage NEO 8000 Bedienungsanleitung
Part Number 104373-102 05/2008 ©2005 - 2008 Overland Storage, Inc. Page 1 of 4
This document describes how to unpack and set up a new
NEO 8000 Library. This same information is also found in
the Overland NEO 8000 Library User Guide.
WARNING: Due to the weight and size of the library, it
is recommended that at least two people be involved
with the unpacking process.
CAUTION: Read and become familiar with the entire
document before starting this unpacking procedure.
Steps performed out of sequence may cause damage to
the library which voids existing warranties.
NOTE: Retain all packaging materials in a protected place in
case the library needs to be shipped to a different location.
Tools Needed
These tools are required to unpack the library:
•9/16” wrench
•10” adjustable wrench
•Level tool
•Large flat-blade offset screwdriver
•Box knife
•#2 Phillips screwdriver
1. Position the shipping container on a level surface with
adequate clearance to work around it (Figure 1).
NOTE: The container pallet is labeled “RAMP SIDE” on each
corner of the removal side.
•Allow at least 10 ft. (3.0m) of clearance on the
removal side of the container
•Allow about 3 ft. (1.0m) of clearance around the other
three sides of the container
•Allow at least 8 ft. (2.5m) of vertical clearance
Figure 1. Unpacking Space Requirements
NEO 8000™ Library
Important Unpacking
Instructions
Overview & Notes
Removing the Outer Carton
NEO-8117`
Ramp (Front)
Floor
Allow at least 10 ft. (3.0m)
to remove the library
from the pallet.
Allow 3 ft.
(1.0m) around
the library
Allow 8 ft.
(2.5m) vertical
clearance
Part Number 104373-102 05/2008 ©2005 - 2008 Overland Storage, Inc. Page 2 of 4
2. Remove the outside packaging (Figure 2).
a. Cut the three (3) shipping straps and remove.
b. Remove the six (6) shipping strap reinforcing
corners from around the box.
c. Remove the top cap.
d. Release and remove each of the eight (8) plastic
retainers (four each on opposite corners).
Figure 2. Library Packaging Components (Rear View)
e. Remove the two (2) large pieces of cardboard
surrounding the library.
3. Remove the inner packaging (Figure 3).
a. Remove the two (2) pads on top of the library.
b. Remove the Ramp and Door boxes and set them
aside.
c. Remove the plastic sheet that covers the library.
Figure 3. Ramp and Door Box Locations
1. Remove the ramps from the Ramp box and lay them
down, placing the brackets into the corresponding slots
in the pallet (Figure 4).
Figure 4. Placing the Ramps in Position
2. Remove the rear hardware holding the library on the
pallet.
a. To provide access to the hold-down bolts and leveling
legs, remove the rear door of the library; set aside.
b. Remove the four (4) crossbar screws from the pallet.
c. Remove the rear crossbar (Figure 5).
Figure 5. Removing the Rear Crossbar
d. Using the 9/16” wrench, remove the two bolts and
hold-down brackets.
e. Use the 10” adjustable wrench to loosen and raise
the two leveling legs (Figure 6 on page 3).
NEO-8113
Plastic
Strap
Corners
Reinforcing
Shipping
Retainers
Straps
Top Cap
NEO-8144
Ramp Box
(Library hidden for clarity)Front
Top Pads
Door Box
Detaching the Pallet
NEO-8115
(Library hidden for clarity)
Slots
Ramps
Crossbar Screws
NEO-8116
Front Crossbar
Bolts
(Library hidden for clarity)
Rear Crossbar
(Remove First)
Part Number 104373-102 05/2008 ©2005 - 2008 Overland Storage, Inc. Page 3 of 4
Figure 6. Raising the NEO 8000 Leveling Legs
3. Remove the front hardware holding the library on the
pallet.
a. Use the 9/16” wrench to remove the bolts and
hold-down brackets.
Lift the front crossbar ends, as needed, for access.
b. Carefully roll the library back 1.25” (3cm) and
remove the front crossbar.
c. Use the adjustable wrench to loosen and raise the
two leveling legs (Figure 6).
4. Verify that all four leveling legs can clear the floor at
the bottom of the ramp and that the library is only
supported by the four caster wheels.
WARNING: Most of the weight of a library is located
in the rear. If the leveling legs are not raised high
enough, they can catch at the bottom of the ramps,
tipping over the library.
5. Carefully move the library down the ramps and onto
the floor.
CAUTION: Do not pull on the media drawer handles
when moving the library.
Before moving the library to its final operating position,
attach the doors.
1. Reattach the back door to the rear of the library.
2. Remove the two doors from the Door shipping box;
then, remove them from their plastic shipping bags.
NOTE: The square, straight end of the door is the top and the
curved end is the bottom.
3. Locate the bag of nylon washers taped inside one of
the doors.
The washers are used as bearings between the hinges.
4. Attach the left door (Figure 7).
a. Lift the top hinge pin just enough to retract the tip
into the left door’s hinge block.
b. Place one nylon washer onto the bottom hinge pin
that protrudes below the door hinge block.
It is held in place by the hinge pin’s ball retainer.
c. Position the door vertically with the bottom hinge
pin above the library hinge block hole and seat it.
d. Raise the door slightly, push down the top hinge.
pin slightly, and place a nylon washer onto it.
It is held in place by the hinge pin’s ball retainer.
Figure 7. Attaching the Front Doors
NEO-8106
Attaching the Doors
NEO-8091
Nylon Washers
Door
Left Door
Hinge
Block
Library Hinge Block
(between hinges)
Hinge Pin
Door Check
Part Number 104373-102 05/2008 ©2005 - 2008 Overland Storage, Inc. Page 4 of 4
e. Lower the door so that the top hinge pin is above
the library hinge block hole and seat it.
5. Check the door to make sure it closes smoothly, yet is
held firmly.
6. If the door does not close as described in Step 5, adjust
it for alignment and operation:
a. Using the flat-blade offset screwdriver, unscrew the
door checks in both left library hinge blocks until
the door closes freely (Figure 7 on page 3).
b. Close the door and check that the top edge of the
door meets the front panel façade evenly.
•If the door is low, add washers to raise the door.
•If the door is high, remove the top washer.
CAUTION: The weight of the door should be
carried by at least one hinge with a nylon washer
(i.e., there must be at least one washer).
c. When the door height is correct, screw in the door
checks until the door closes smoothly, yet is held
firmly.
7. Repeat Steps 4–5 for the right door; if needed,
repeat Step 6.
Move the library into its final position and level it:
CAUTION: Do not pull on the media drawer handles
when moving the library.
1. Position the library at its operating location.
2. Run down all four leveling legs by hand until they
contact the floor.
3. Using the 10” adjustable wrench, turn each leg, one
after the other in equal increments, until you have
turned them at least one full turn.
NOTE: Be sure the library has been raised high enough so
none of the casters touch the floor.
4. Place the level, front to rear, on the top side edge of
the library (see Figure 8).
5. Note the position of the bubble. Raise both of the front
legs or both of the rear legs the same amount to
achieve a level front-to-rear reading.
6. Place the level across the top front edge of the library.
7. Note the position of the bubble. Raise both of the left
feet or both of the right feet the same amount to
achieve a level side-to-side reading.
8. Recheck the level from front-to-rear and from
side-to-side. Adjust as needed until the library is level.
Figure 8. Positioning the Level
You are now ready to connect the library to your network. Refer to the Overland NEO 8000 Library User Guide for
information required to complete this installation.
Leveling the Library
NEO-8112
What’s Next?
Additional Help
You can get additional technical support on the Internet at http://support.overlandstorage.com, or call
1-877-654-3429 (toll-free U.S. & Canada), +44 (0) 118-9898050 (Europe), or +1 (858) 571-5555 Option 5 (International).
Andere Handbücher für NEO 8000
12
Inhaltsverzeichnis
Andere Overland Storage Lagerung Handbücher
Overland Storage
Overland Storage SnapServer Service-Handbuch
Overland Storage
Overland Storage REO Series Bedienungsanleitung
Overland Storage
Overland Storage SnapScale X4 Node Leitfaden
Overland Storage
Overland Storage NEO 200S Bedienungsanleitung
Overland Storage
Overland Storage SnapScale X2 Bedienungsanleitung
Overland Storage
Overland Storage LTO-4 Bedienungsanleitung
Overland Storage
Overland Storage SnapServerXSR 40 Bedienungsanleitung
Overland Storage
Overland Storage REO 9000 Bedienungsanleitung
Overland Storage
Overland Storage SnapExpansion XSR Bedienungsanleitung
Overland Storage
Overland Storage PowerLoader Bedienungsanleitung
Overland Storage
Overland Storage Neo Series 2000 Bedienungsanleitung
Overland Storage
Overland Storage NEO 8000 Bedienungsanleitung
Overland Storage
Overland Storage REO 9100 Anleitung zur Verwendung
Overland Storage
Overland Storage ARCvault 12 Bedienungsanleitung
Overland Storage
Overland Storage ARCvault Series Leitfaden
Overland Storage
Overland Storage ULTAMUS RAID 4800 Bedienungsanleitung
Overland Storage
Overland Storage SnapServer XSD 40 Bedienungsanleitung
Overland Storage
Overland Storage NEO 8000 Bedienungsanleitung
Overland Storage
Overland Storage Ultamus Raid 1200 Bedienungsanleitung
Overland Storage
Overland Storage NEO XL Series Bedienungsanleitung
Beliebte Lagerung Handbücher anderer Marken
Spectra Logic
Spectra Logic T-Series Spectra T50e Bedienungsanleitung
Panasonic
Panasonic LKM-F931-1 Bedienungsanleitung
Tabernus
Tabernus Enterprise Erase E2400 Bedienungsanleitung
Rocstor
Rocstor COMMANDER 3F series Bedienungsanleitung
HP
HP P9000 Bedienungsanleitung
Western Digital
Western Digital Ultrastar Data60 Bedienungsanleitung