Ovislink HP-1000E v2 Bedienungsanleitung
HP-1000E v2
Powerline Ethernet Adapter
User’sManual
HP1000E v2 User’s Manual
Table of Contents
Chapter 1: Introduction .........................................................................................1
Chapter 2: Planning your Powerline Network .......................................................1
Network Topology..............................................................................................1
Chapter 3: Getting to Know the Powerline Adapter...................................................2
The Top Panel ...................................................................................................2
The Front Panel.................................................................................................2
Chapter 4: Connecting the Powerline Ethernet Adapter .................................................3
Connecting the Adapter.....................................................................................3
Connecting to a Router......................................................................................4
Chapter 5: Using the Powerline Configuration Utility ............................................4
Utility Installation................................................................................................4
Accessing the Powerline Configuration Utility....................................................5
Device tab.......................................................................................................5
Network tab.....................................................................................................6
Security...........................................................................................................7
About ..............................................................................................................8
Appendix A: Troubleshooting................................................................................9
Common Problems and Solutions......................................................................9
Frequently Asked Questions............................................................................10
Appendix B: Specifications .................................................................................11
Appendix C: Regulatory Information...................................................................11
WARNING: This product contains chemicals, including lead, known to the State of California to cause
cancer, and birth defects or other reproductive harm. Wash hands after handling.
How to Use this User Guide
The user guide to the Powerline Ethernet Adapter has been designed to make understanding networking
with the Powerline Ethernet Adapter easier than ever. Look for the following items when reading this User
Guide:
This checkmark means there is a note of interest and is something you should pay special
attention to while using the Powerline Ethernet Adapter.
This exclamation point means there is a caution or warning and is something that could damage
your property or the Powerline Ethernet Adapter .
HP1000E v2 User’s Manual
Chapter 1: Introduction
Thank you for choosing the HP-1000E v2 Powerline Ethernet Adapter. The Adapter will allow you
to network better than ever. How does the Adapter do all of this? The Powerline Ethernet Adapter
lets you turn the existing Powerlines in your home or office into a high-speed network. Now you
don’t have to drill through the walls, and climb through theattic or cellar to install network cables,
just use the wires that already run through the building.
But what does all of this mean?
Networks are useful tools for sharing computer resources. You can access one printer from
different computers and access data located on another computer's hard drive. Networks are
even used for playing multiplayer video games. So, networks are not only useful in homes and
offices, they can also be fun.
The Powerline Adapter interfaces Ethernet devices to the HomePlug Powerline network standard.
Just plug the Powerline Adapter into the wall, and connect your Ethernet-equipped device to the
Adapter using the included network cable, and you’ve turned your whole house into a network
infrastructure. Attach more computers to the network by simply plugging them into the wall
anywhere in the house, using more Powerline Adapters, or the Powerline USB Adapter.
Once your computers are connected to the network, they can share resources like printers and
storage space,
and all kinds of files: music, digital pictures, and documents. With up to 14Mbps data rates, you
can play head-to head network computer games, too. And if you use a Powerline Adapter to
interface Broadband Routers from your cable or DSL Internet connection to your Powerline
network, you’ll be able to get to the Internet from any computer in the house.
Use the instructions in this Guide to help you connect the Adapter, set it up, and configure it to
adapter your different networks. These instructions should be all you need to get the most out of
the Adapter.
Chapter 2: Planning your Powerline Network
NETWORK TOPOLOGY
With the Powerline products, a network can be created
using home Powerlines. Computers can be networked
over Powerlines using Powerline devices. The Adapter
connects an Ethernet-enabled computer to a Powerline
network. The Powerline USB Adapter is also available
for connecting a USB-enabled computer to a Powerline
network.
The Adapter is also ideal for any user who already has a
router and wants to share high-speed Internet access
across the Powerline network. Connect the Adapter to
the router after you have configured the Adapter using
the Powerline Configuration Utility. Connect a straight-through Category 5 Ethernet network cable
to the uplink port of the router, or connect a crossover Category 5 Ethernet network cable to a
LAN port on the router.
- 1 - HP1000E v2 User’s Manual
Chapter 3: Getting to Know the Powerline Adapter
THE TOP PANEL
The Adapter’s Port, where the Ethernet Port is connected,
is located on the front panel.
Ethernet:
The Ethernet Port is where you will connect the included
Category 5 Ethernet network cable.
THE FRONT PANEL
The Adapter’s LEDs, where information about network activity is displayed, are located on the
front panel. .
Power: Blue, The Activity LED will flash when there is data transmitted over the Powerline
network.
Ethernet: Blue, The Ethernet LED will be lit steadily when there is an active Ethernet connection.
Link/Act: Blue, The Link LED will light up when the Powerline Adapter is powered on.
- 2 - HP1000E v2 User’s Manual
Chapter 4: Connecting the Powerline Ethernet Adapter
CONNECTING THE ADAPTER
IMPORTANT: Do NOT use a switch to connect multiple Powerline devices to your PC’s Ethernet
port. Each Powerline device should be connected to its own Ethernet port on the PC.
1. Plug the included Category 5 Ethernet network cable into the computer’s Ethernet port.
2. Plug the other end of the cable into the Ethernet port of the Adapter.
3. Plug the Adapter into an electrical outlet.
- 3 - HP1000E v2 User’s Manual
IMPORTANT:
Because the Adapter sends data over the power lines of your house,
plug the Adapter directly into an electrical outlet. Do not plug the device into a UPS
or power strip with surge protection. The Adapter has its own power filter for
protection against surges.
The installation of the Adapter is complete. If you want to configure the Adapter, proceed
to “Chapter 5: Using the Powerline Configuration Utility.”
CONNECTING TO A ROUTER
If you want to connect the Adapter to a router, then proceed to the next section, “Connecting to a
Router.”
If you want to share high-speed Internet access across a Powerline network, then you can
choose to connect the Adapter to a router.
Follow these instructions:
Disconnect the network cable from the PC, and connect it to the uplink port of the router. If you
only have a LAN port available on the router, then use a crossover Category 5 Ethernet network
cable to connect the Adapter to the router. The installation of the Adapter is complete.
Chapter 5: Using the Powerline Configuration Utility
Overview
After installing the Adapter, you will run the Setup Wizard to install the Powerline Configuration
Utility. Use this utility to check the PC’s direct connection to the Powerline network, search for
Powerline devices on your network, and set up security using a network password.
Note: If you want the devices on your Powerline network to share high-speed
internet access, connect the Adapter to a router after you run the Powerline
Configuration Utility. Refer to “ Chapter 4: Connecting the Powerline Ethernet
Adapter.”
UTILITY INSTALLATION
1. Insert the included utility CD into the CD-ROM drive of your computer
2. The system will automatically search for the destination location, just click Next to continue.
- 4 - HP1000E v2 User’s Manual
3. When the InstallShield Wizard screen appears, click Install to start the utility installation.
4.Click Finish to complete the installation.
ACCESSING THE POWERLINE CONFIGURATION UTILITY
To access the Powerline Configuration Utility, double-click the Powerline Configuration Utility icon
on your desktop.
Device tab
The Device screen lists the Powerline devices connected to your PC.
- 5 - HP1000E v2 User’s Manual
State This indicates which Powerline device is currently used by
the PC.
Device The name of each Powerline device is displayed here.
MAC address The MAC address of each Powerline device is shown here.
Refresh Click Refresh to analyze your Powerline network and
refresh the list.
Connect Select the Device you want to use to access the Powerline
network, and then click the Connect button.
Link Quality The signal quality of the Powerline network connection is
indicated here.
Network tab
The Network screen allows you to search the Powerline network for all Powerline devices
configured with the same Network Password as the device you are currently using for your PC.
- 6 - HP1000E v2 User’s Manual
MAC Address The MAC address of each Powerline device is shown
here.
Data Rate (Mbps) The transmission speed of the Powerline device is
displayed here.
Scan Powerline
Network Click the Scan Powerline Network button to perform a
search for all Powerline devices configured with the
same Network Password.
Security
The Security screen allows you to set the Network Password of the Powerline device being used by
your PC. All of the Powerline devices on your Powerline network must use the same Network
Password.
Note: Remember this password. You will need to set this password on
each powerline device on your powerline network.
Network Password By default the Network password is “HomePlug” and the
password must have between 4 and 24 characters. The Network
Password is case-sensitive, so note whether you use lowercase
or uppercase letters. It can include any letters of the alphabet,
numbers, or punctuation marks
Set Local Enter the Network Password in the Network Password field. Then
click the Set Local button.
Restore Default Click the Restore Default button to set the Network Password
back to its factory default setting, HomePlug. Then click the Set
button.
- 7 - HP1000E v2 User’s Manual
About
The About screen shows the version of this device.
Note about OK and Cancel buttons:
OK Click to save all settings.
Cancel Click to discard changes or close windows.
- 8 - HP1000E v2 User’s Manual
Inhaltsverzeichnis
Andere Ovislink Adapter Handbücher
Ovislink
Ovislink AirLive WN-380USB Bedienungsanleitung
Ovislink
Ovislink OVT-12 Bedienerhandbuch
Ovislink
Ovislink PL-DUO210/85 Bedienungsanleitung
Ovislink
Ovislink EVO-W311AR Bedienungsanleitung
Ovislink
Ovislink Air Live WLA-5000AP Bedienungsanleitung
Ovislink
Ovislink Air Live GE-2032R Bedienungsanleitung
Ovislink
Ovislink AirLive HP-3000E Bedienungsanleitung
Ovislink
Ovislink WIRELESS-G PCI ADAPTER Bedienungsanleitung
Ovislink
Ovislink AirLive EtherWe-1000U Bedienungsanleitung
Ovislink
Ovislink EVO-W301USB Bedienungsanleitung
