OVS 4CH-P4 Benutzerhandbuch

Network Video Recorder

Quick Operation Guide

Quick Operation Guide of 8700-P Series NVR

Thank you for purchasing our product. If there is any question or request, please do not hesitate to contact dealer.

This manual is applicable to the models listed in the following table.

Series

Model

Type

8700-P series

4CH(4 POE)

8CH(4 POE)

8CH(8 POE)

16CH(8 POE)

Network Video Recorder

NVR Pre-Installation

This series NVR are highly advanced surveillance equipment that should be installed with care. Please take into

consideration the following precautionary steps before installation of the NVR.

1. Keep all liquids away from the NVR.

2. Install the NVR in a well-ventilated and dust-free area.

3. Ensure environmental conditions meet factory specifications.

4. Install a manufacturer recommended HDD.

NVR Installation

During the installation of the NVR:

1. Use brackets for rack mounting.

2. Ensure there is ample room for audio and video cables.

3. When installing cables, ensure that the bend radius of the cables are no less than five times than its diameter.

4. Connect both the alarm and RS-485 cable.

5. Allow at least 2cm (≈0.75-inch) of space between racks mounted devices.

6. Ensure the NVR is grounded.

7. Environmental temperature should be within the range of -10 ºC ~ 55 ºC , 14ºF ~ 131ºF.

8. Environmental humidity should be within the range of 10% ~ 90%.

Hard Disk Installation

Before you start:

Before installing a hard disk drive (HDD), please make sure the power is disconnected from the NVR. A factory

recommended HDD should be used for this installation.

Up to 2 SATA hard disks can be installed on your NVR.

Tools Required: Screwdriver.

Steps (for 8700 Series):

Note: The installation steps of 8/16 Series is the same as 4ch series, so we take the installation steps of 4ch as

example.

1. Remove the cover from the NVR by unfastening the screws on the back and side.

Quick Operation Guide of 8700-P Series NVR

2. Connect one end of the data cable to the motherboard of NVR and the other end to the HDD.

3. Connect the power cable to the HDD.

4. Place the HDD on the bottom of the device and then fasten the screws on the bottom

to fix the HDD.

5. Re-install the cover of the NVR and fasten screws.

Quick Operation Guide of 8700-P Series NVR

Front Panel

8700-P Series

①Status Indicators (Alarm, Ready, Status, HDD, power, Tx/Rx)

②USB Interfaces

③Composite Keys

④SHIFT

⑤Compound Buttons

Quick Operation Guide of 8700-P Series NVR

Rear Panel

8700-P Series(with 4 POE)

Note: The rear panels of others provide 8 POE interfaces.

No.

Item

Description

LAN Network Interface

Connector for LAN (Local Area Network).

RS-485 Interface

Connects to RS-485 devices.

Power Supply

100~240VAC power supply

Power Switch

Switch for turning on/off the device.

USB Interface

Universal Serial Bus (USB) ports for additional devices such as USB

mouse and USB Hard Disk Drive (HDD).

GND

Ground (needs to be connected when NVR starts up).

HDMI Interface

HDMI video output connector.

VGA Output

DB9 connector for VGA output. Display local video output and menu.

Audio In

RCA connector for voice talk input

Audio Out

RCA connector for audio output

Network Interfaces with

PoE function

(for B Series)

Network interface for the cameras and to provide power over Ethernet.

Quick Operation Guide of 8700-P Series NVR

Specifications

Model

4CH-P4

8CH-P4/P8

16CH-P8

Video/Audio

input

IP video input

4-ch

8-ch

16-ch

Two-way audio input

1-ch, RCA (2.0 Vp-p, 1kΩ)

Bandwidth

Incoming bandwidth

20Mbps

40Mbps

80Mbps

Output bandwidth

40Mbps

Video/Audio

output

Decoding resolution

5MP/3MP/1080p/UXGA/720p/VGA/4CIF/DCIF/2CIF/CIF/QCIF

HDMI/VGA output

1-ch, resolution:

1920 × 1080P /60Hz, 1600 × 1200 /60Hz, 1280 × 1024 /60Hz,

1280 × 720 /60Hz, 1024 × 768 /60Hz

CVBS

1-ch, BNC (1.0 Vp-p, 75 Ω)

Resolution: 704 ×576 (PAL); 704 ×480 (NTSC) (optional)

Audio output

1-ch, RCA (Linear, 1kΩ)

Playback resolution

5MP /3MP /1080P /UXGA /720P /VGA /4CIF /DCIF /2CIF /CIF

/QCIF

Synchronous playback

4-ch, 720P / 2-ch,

1080P / 1-ch, 5MP

8-ch 4CIF /4-ch, 720P / 2-ch, 1080P / 1-ch,

5MP

Hard disk

SATA

2 SATA interfaces for 2 HDDs

Capacity

Up to 4TB for each disk

External

interface

Network interface

1 RJ-45 10 /100 /1000 Mbps self-adaptive Ethernet interface

4/8 independent 10 /100 Mbps PoE Ethernet interfaces

Serial interface

1 RS-485 half-duplex interface

USB interface

2 ×USB 2.0

Alarm in/out

4/1 (optional)

Others

Power supply

100~240VAC, 47~63Hz, 3A

Consumption

≤ 15 W (without hard disk)

Working temperature

-10 ºC ~ +55 ºC (14 ºF ~ 131 ºF)

Working humidity

10 % ~ 90 %

Chassis

19-inch rack-mounted 1U chassis

Dimensions

(W ×D ×H)

445 ×290 ×45mm (175.2 ×114.2 ×17.7 inch)

Weight

≤ 2 Kg (4.4 lb) (without hard disk)

Quick Operation Guide of 8700-P Series NVR

HDD Storage Calculation Chart

The following chart shows an estimation of storage space used based on recording at one channel for an hour at a

fixed bit rate.

Bit Rate

Storage Used

96K

42M

128K

56M

160K

70M

192K

84M

224K

98M

256K

112M

320K

140M

384K

168M

448K

196M

512K

225M

640K

281M

768K

337M

896K

393M

1024K

450M

1280K

562M

1536K

675M

1792K

787M

2048K

900M

Note: Please note that supplied values for storage space used is just for reference. Storage space used is estimated

by formulas and may have some deviation from actual value.

Quick Operation Guide of 8700-P Series NVR

Menu Operation

Menu Structure

Startup and Shutdown

Proper startup and shutdown procedures are crucial to expanding the life of the NVR.

To start your NVR:

1. Check the power supply is plugged into an electrical outlet. It is HIGHLY recommended that an

Uninterruptible Power Supply (UPS) be used in conjunction with the device. The Power indicator LED on

the front panel should be red, indicating the device gets the power supply.

2. Turn on the power switch on the rear panel to start the NVR immediately.

To shut down the NVR:

1. Enter the Shutdown menu.

Menu > Shutdown

Shutdown Menu

2. Select the Shutdown button.

3. Click the Yes button.

4. Shut the power switch down when the shutdown attention pops up.

Quick Operation Guide of 8700-P Series NVR

Using the Start Wizard

By default, the Setup Wizard starts once the NVR has loaded, as shown in Figure below.

Start Wizard Interface

Operating the Setup Wizard:

1. The Setup Wizard can walk you through some important settings of the NVR. If you don’t want to use the

Setup Wizard at that moment, click the Cancel button. You can also choose to use the Setup Wizard next

time by leaving the “Start wizard when NVR starts?” checkbox checked.

2. Click Next button on the Wizard window to enter the Login window.

3. Enter the admin password. By default, the password is 12345.

4. To change the admin password, check the New Admin Password checkbox. Enter the new password and

confirm the password in the given fields.

5. Click the Next button to enter the date and time settings window.

Quick Operation Guide of 8700-P Series NVR

Date and Time Settings

6. After the time settings, click Next button which takes you back to the Network Setup Wizard window.

Network Configuration

Note: For A Series, B Series and C Series series NVR, the internal NIC IPv4 address should be configured for the

cameras connecting to the PoE network interface or the built-in switch of the NVR.

7. Click Next button after you configured the network parameters, which takes you to the HDD Management

window.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere OVS Netzwerk-Hardware Handbücher

OVS

OVS LTN8608-P8 Bedienungsanleitung

Beliebte Netzwerk-Hardware Handbücher anderer Marken

Matrix Switch Corporation

Matrix Switch Corporation MSC-HD161DEL Bedienungsanleitung

B&B Electronics

B&B Electronics ZXT9-IO-222R2 Bedienungsanleitung

Yudor

Yudor YDS-16 Bedienungsanleitung

D-Link

D-Link ShareCenter DNS-320L Bedienungsanleitung

Samsung

Samsung ES1642dc Gebrauchsanweisung

Honeywell Home

Honeywell Home LTEM-PV Montageanleitung

evertz

evertz 7700 Series Bedienungsanleitung

D-Link

D-Link ShareCenter DNS-343 Bedienungsanleitung

Asante

Asante AsanteBridge 1012 Bedienungsanleitung

FireBrick

FireBrick FB2700 Bedienungsanleitung

Audiovox Electronics

Audiovox Electronics ARWH2T Bedienungsanleitung

ADC

ADC DSX-1 Handbuch

NetComm

NetComm NF2 Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent 5620 Bedienungsanleitung

Dell EMC

Dell EMC XC6420 Series Bedienungsanleitung

Lanner

Lanner NCA-1020A Bedienungsanleitung

Allied Telesis

Allied Telesis AT-TN121-A Bedienungsanleitung

Arista

Arista CCA-ETM-Q12 Bedienungsanleitung