OWC U.2 SHUTTLE Leitfaden
U.2 SHUTTLE
3.5-inch U.2 NVMe SSD Carrier Shuttle
Ideal for Media Production Workows
Ooad day’s shoot and send drive to post
Fast and Easy Drive Swaps
Move between U.2 devices,
PCs, and servers
RAID Ready
Harness the power of RAID 0, 1, 4, 5, or 10
via your choice of RAID utilities
TABLE OF CONTENTS
INTRODUCTION
1.1 Minimum System Requirements .................................................................... 3
1.2 Packaging Contents ........................................................................................ 3
1.3 About This Manual........................................................................................... 3
DEVICE SETUP
2.1 Installation of M.2 Drive(s).............................................................................. 4
2.2 Host Installation: Helios 3S with U.2 NVMe Interchange System ...............5
2.3 Host Installation: ThunderBay Flex 8 ............................................................. 6
2.4 Host Installation: Mercury Pro U.2 Dual ......................................................... 7
2.5 Usage Notes..................................................................................................... 8
SUPPORT RESOURCES
3.1 Troubleshooting............................................................................................... 9
3.2 Formatting........................................................................................................ 9
3.3 About Data Backup.......................................................................................... 9
3.4 Contacting Technical Support......................................................................... 9
TABLE OF CONTENTS
03INTRODUCTION
1.1 SYSTEM REQUIREMENTS
Operating System:
- Mac and PC OS requirements differ based on enclosure type (see below)
Hardware:
- Mac or PC with an enclosure supporting a 3.5-inch drive form-factor using an NVMe U.2 connection.
Supported OWC enclosures include:
- OWC ThunderBay Flex 8 (top 4 bays only, top-left recommended)
- OWC Mercury Helios 3S with U.2 NVMe Interchange System
- OWC Mercury Pro U.2 Dual
Supported Drives Types:
- (4) NVMe M.2 drives with 2280 form factor and M-key connector
1.2 PACKAGE CONTENTS
INTRODUCTION
OWC U2 Shuttle Security keys Quick start guide
1.3 ABOUT THIS MANUAL
The images and descriptions may vary slightly between this manual and the unit shipped. Functions and features may
change depending on the rmware version. The latest product details and warranty information can be found on the
product web page. OWC’s Limited Warranty is not transferable and subject to limitations.
04DEVICE SETUP
DEVICE SETUP
2.1 INSTALLATION OF M.2 DRIVE(S)
This section describes the process of installing one or more
M.2 drives into the OWC U2 Shuttle. NVMe drives with a 2280
form factor and M-key connector are required. Other M.2 drive
types are not supported.
1. Remove the device from the retail packaging and set
it on a static-free work surface.
2. Remove the four cover screws at the locations shown
(there are two on each side).
3. Lift the cover off the device and set it aside.
4. Based on the number of M.2 drives you wish to install,
remove the screws from the corresponding drive posts
(highlighted), then set them aside.
5. For each SSD, align the M-key connector on the drive with
a connector on the PCBA and carefully seat the drive
in the connector. Minimal force is required. If a drive does
not seat correctly, do not apply more force. Remove the
drive, re-align it, and try again. Note: once seated
it is normal for each drive to sit at an angle.
6. For each SSD, hold the end of the M.2 drive down against
the corresponding drive post, then re-affix the screw you
removed earlier, to secure the drive in place.
7. Re-seat the cover, making sure that it sits flush with
the shuttle chassis on all sides. While maintaining a
modest amount of downward pressure on the cover,
re-affix the four screws you removed in Step 2 to secure
it. IMPORTANT: when the cover is seated and affixed
correctly, the tops of the “fins” on the cover will sit flush
with the top edges of the chassis. This reduces the
potential for installation issues when working with the
U.2 NVMe Interchange System.
This completes the drive installation process.
- To install with Mercury Helios 3S and U.2 NVMe
Interchange System, go to Section 2.2.
- To install in a ThunderBay Flex 8, skip to Section 2.3.
- To install in Mercury Pro U.2 Dual, skip to Section 2.4
3
5
7
4
6
05DEVICE SETUP
2.2 HOST INSTALLATION: HELIOS 3S WITH U.2 NVME
INTERCHANGE SYSTEM
This section describes the process of installing the OWC U2
Shuttle into the U.2 NVMe Interchange System. If you are
using both devices for the first time, you need to set up the
Helios 3S with the interchange system first. Please see the
assembly manual at www.owc.com/support/manuals for
instructions, then return to this page to install the Shuttle.
1. Note the shape of the cutout on the back of the U.2 NVMe
Interchange System; when installing the U2 Shuttle, you
need to first rotate it so that the side with the U.2 connector
is facing up. Make sure the connector is oriented to the left,
far edge.
2. Carefully slide the shuttle into the U.2 Interchange chassis.
When the shuttle contacts the U.2 connector inside the
device, a modest amount of force is required to fully
connect them. If the shuttle does not seat, do not apply
more force. Slide it back a small amount and then try again.
When seated it should “snap” into place.
IMPORTANT: when the cover is seated and affixed
correctly, the tops of the “fins” on the cover will sit flush
with the top edges of the chassis. If this is not the case,
you may have difficulty completing this step and potentially
cause cosmetic damage to the fins on the Shuttle. If the
fins are not completely flush please re-visit Section 2.2,
Step 7. You may need to remove and then reseat and re-
affix the cover, as described.
3. If you would like to lock the U2 Shuttle into place, insert
the included key into the lock and turn it until the lock
is secured, then remove the key.
Note: even though you are not using a PCIe card, this
Helios 3S configuration is not hot-swappable. Each time
you perform this installation you should power the Helios
3S off and disconnect it from power and the host computer,
install the U2 Shuttle, then reconnect the Helios 3S.
You can now mount the Helios 3S to your host computer,
format and/or RAID the M.2 drives installed using SoftRAID
or the RAID Assistant feature in Apple’s Disk Utility
application, and then begin using the drives.
06DEVICE SETUP
2.3 HOST INSTALLATION: THUNDERBAY FLEX 8
This section describes the process of installing the OWC U2
Shuttle into the ThunderBay Flex 8. If you are using both
devices for the first time, please familiarize yourself with the
ThunderBay and its drive sleds first. Please see the assembly
manual at www.owc.com/support/manuals for instructions,
then return to this page to install the Shuttle.
1. While it’s possible to install a U.2 drive or the U2 Shuttle
in any of the top four bays, we strongly recommend the
top-left bay to get the best performance. This bay offers
four lanes of PCIe bandwidth (x4) while the other three only
offer a single lane each (x1).
2. Seat the U2 Shuttle into the drive sled, making sure the
connector on the bottom of the shuttle is aligned with the
connector cutout at the front edge of the sled.
3. Also make sure the six screw holes on the shuttle (3 aside)
align with the corresponding holes on the sides of the drive
sled, then affix the shuttle using six of the 3.5 inch drive
screws that shipped with the ThunderBay.
4. Align the drive sled with the corresponding track inside the
chassis, then carefully insert the sled and slide it back until
the connector on the shuttle seats with the connector on
the ThunderBay; this is similar to the drive install process
described in Section 2.1, Step 8 in the ThunderBay manual.
If it does not seat initially, do not apply more force, remove
the tray, re-align it and try again.
Once the OWC U2 Shuttle is installed, you can format
and/or RAID the M.2 drives installed using SoftRAID
or the RAID Assistant feature in Apple’s Disk Utility
application, and then begin using the drives.
3 4
07DEVICE SETUP
2.4 HOST INSTALLATION: MERCURY PRO U.2 DUAL
This section describes the process of installing the OWC U2
Shuttle in the Mercury Pro U.2 Dual. The instructions listed
here will the same or very similar to the ones found in that
product’s assembly manual, located at
www.owc.com/support/manuals.
1. Remove Mercury Pro U.2 Dual from its packaging and set
it on a static-free work surface.
2. Remove the two screws highlighted in red from the back
of the enclosure and set them aside.
3. Pull on the front plate of the enclosure so the inner-chassis
slides out (A), then remove it fully (B).
4. Set the inner chassis flat on the work surface.
5. Making sure the connector on the shuttle aligns with
the connector on the inner-chassis, place the shuttle into
the housing. Then, connect the inner-chassis to the U2
Shuttle by sliding it in the direction shown until it is fully
seated. If the device does not seat fully, do not apply more
force. Move it back and try again. As long as the OWC U2
Shuttle is sitting flush in the drive carrier, the connectors
should automatically align.
6. Affix the U2 Shuttle to the inner-chassis at the locations
shown. Note: the hole for a 2.5 inch U.2 drive is circled in
yellow. A total of one screw is required for 2.5 inch drives,
and four screws (two per side) for 3.5 inch drives and the
OWC U2 Shuttle.
7. Once the U2 Shuttle is secured, flip the inner chassis
if needed and repeat Steps 5 and 6 to install another U.2
device or OWC U2 Shuttle.
3a 3b
5
7
4
6
08DEVICE SETUP
8. Make sure the ports on the back of the inner chassis and
the port cut-outs on the back of the outer enclosure are
oriented the same way, then slide the inner chassis into the
outer enclosure so that the chassis’ front plate is flush with
the cover’s front edge.
9. Re-affix the screws you removed in Step 2.
This completes the assembly process.
Once you’ve completed the installation steps, you can
format and/or RAID the M.2 drives using SoftRAID or the
RAID Assistant feature in Apple’s Disk Utility application,
and then begin using the drives. You can also format and
use the individual M.2 drives as independent volumes,
or a mix of independent and RAID volumes.
9
8
8
2.5 USAGE NOTES
- When using this device with a ThunderBay Flex 8, the top-left drive bay is recommended because it
provides the greatest PCIe bandwidth, to be shared among the drives installed in the Shuttle. The other 3
bays in the top row will function, but at potentially much slower speeds, unless you’re using a single M.2
drive in the shuttle.
09SUPPORT RESOURCES
3.1 TROUBLESHOOTING
Most problems with the U2 Shuttle can be traced back to one or more improperly installed M.2 drives and/
or a shuttle that is not fully connected to the host enclosure in which it is being used. Please disconnect
any host enclosure from power, remove the U2 Shuttle, then remove the cover and inspect the M.2 drive
connections. If they’re OK, re-seat and ax the cover, then re-seat the U2 Shuttle itself into the bay or drive
sled you’re using and try again. If you are still unable to see the M.2 drives in your system afterward, please
contact Technical Support.
3.2 FORMATTING
For additional formatting information, including instructions on how to format your M.2 SSDs for Mac
or Windows, go to: www.owc.com/support/formatting
3.3 ABOUT DATA BACKUP
To ensure that your les are protected and to prevent data loss, we strongly suggest that you keep two
copies of your data: one copy on your OWC U2 Shuttle and a second copy on your internal drive or another
storage medium, such as an optical backup, or on a second external storage unit. Any data loss or
corruption while using the U2 Shuttle is the sole responsibility of the user, and under no circumstances may
OWC, its parent, partners, aliates, ocers, employees, or agents be held liable for loss of the use of data
including compensation of any kind or recovery of the data.
3.4 CONTACTING TECHNICAL SUPPORT
SUPPORT RESOURCES
Phone: M–F: 8am–6pm CT, Sat & Sun: Closed
1.866.692.7100 (N. America) | +1.815.338.4751 (Int’l)
Chat: Sun: 9am–midnight, M–Th: 12am–4am & 7am–midnight (closed from 4am–7am),
Fri: 12am–4am & 7am–10pm (closed from 4am–7am), Sat: 9am–5pm
www.owc.com/support
Email: Answered within 48 hours
www.owc.com/support
CHANGES:
The material in this document is for information purposes only and subject to change without notice.
While reasonable efforts have been made in the preparation of this document to assure its accuracy, OWC,
its parent, partners, aliates, ocers, employees, and agents assume no liability resulting from errors or
omissions in this document, or from the use of the information contained herein. OWC reserves the right
to make changes or revisions in the product design or the product manual without reservation and without
obligation to notify any person of such revisions and changes.
FCC STATEMENT:
Warning! Modications not authorized by the manufacturer may void the user’s authority to operate this
device. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference with radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
WARRANTY:
The U2 Shuttle has a 1 Year OWC Limited Warranty without drives pre-installed and a 3 Year OWC Limited
Warranty on solutions with drive pre-installed. For up-to-date product and warranty information, please visit
the product web page.
COPYRIGHTS AND TRADEMARKS:
No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by
any means, electronic, mechanical, photocopying, recording or otherwise, without the prior written consent
of OWC.
© 2021 Other World Computing, Inc. All rights reserved. OWC, the OWC logo, and U2 Shuttle are trademarks
of New Concepts Development Corporation, registered in the U.S. and/or other countries. Mac and macOS
are trademarks of Apple Inc., registered in the U.S. and other countries. Other marks may be the trademark
or registered trademark property of their owners.
OWCMANU2SHTL – 12.29.2020
Inhaltsverzeichnis
Andere OWC Lagerung Handbücher
OWC
OWC Envoy Gebrauchsanweisung
OWC
OWC Mercury Elite-AL Pro Dual-Drive Bedienungsanleitung
OWC
OWC ThunderBay 4 Leitfaden
OWC
OWC OWC Elite Pro Bedienungsanleitung
OWC
OWC Envoy Bedienungsanleitung
OWC
OWC ThunderBay 8 Leitfaden
OWC
OWC Mercury Pro Leitfaden
OWC
OWC ENVOY PRO FX Bedienungsanleitung
OWC
OWC Mercury Elite Pro Qx2 Leitfaden
OWC
OWC Mercury Elite FireWire 800 Pro Bedienungsanleitung
OWC
OWC Mercury Elite Pro Dual Leitfaden
OWC
OWC MERCURY ELITE PRO MINI Bedienungsanleitung
OWC
OWC miniStack Leitfaden
OWC
OWC Neptune Bedienungsanleitung
OWC
OWC Mercury Elite Pro Dual mini Leitfaden
OWC
OWC Mercury Pro LTO Thunderbolt 3 Bedienungsanleitung
OWC
OWC ENVOY PRO SX Bedienungsanleitung
OWC
OWC Envoy Bedienungsanleitung
OWC
OWC ThunderBlade V4 Bedienungsanleitung
OWC
OWC Mercury Pro LTO Leitfaden
Beliebte Lagerung Handbücher anderer Marken
Spectra Logic
Spectra Logic T-Series Spectra T50e Bedienungsanleitung
Panasonic
Panasonic LKM-F931-1 Bedienungsanleitung
Tabernus
Tabernus Enterprise Erase E2400 Bedienungsanleitung
Rocstor
Rocstor COMMANDER 3F series Bedienungsanleitung
HP
HP P9000 Bedienungsanleitung
Western Digital
Western Digital Ultrastar Data60 Bedienungsanleitung