OXE CoastKey Bedienungsanleitung
1
OXE DIESEL COASTKEY MANUAL
COASTKEY MANUAL
Publication No: ODM1021
DIESEL ENGINE
3
OXE DIESEL COASTKEY MANUAL
PREFACE
ABOUT THIS MANUAL
This manual provides you with the information you need to install, integrate, and
operate your CoastKey wireless kill switch system with your OXE diesel outboard.
It is also recommended to have access to the OXE Diesel Installation Manual.
Specifications and descriptions are subject to change without notice.
CoastKey wireless kill switch system allows you the freedom to move safely
around the boat while preserving the Kill Switch function without being attached
to the traditional kill cord. CoastKey also allows you to start and stop up to four
engines as well as tilting and trimming the engine(s).
It is recommended that the CoastKey system be installed by a professional, with
good knowledge of electrical systems.
Read this manual carefully before using the CoastKey system. Keep the user
manual for future reference.
Cimco Marine AB
Metallgatan 17 B
SE-262 72 Ängelholm, Sweden
+46 (0)431-371130
4
OXE DIESEL COASTKEY MANUAL
5
OXE DIESEL COASTKEY MANUAL
CONTENTS
CONTENTS
Preface ________________________________________________________________________________ 3
About this manual ______________________________________________________________________ 3
Overview_______________________________________________________________________________ 6
Technical data __________________________________________________________________________ 6
Safety and warnings _____________________________________________________________________ 8
Installation _____________________________________________________________________________ 9
Installing the start panel__________________________________________________________________ 9
Connecting the cables __________________________________________________________________ 10
Initiating your PIN code__________________________________________________________________ 11
Pairing the remote control to the start panel_________________________________________________ 12
Operation _____________________________________________________________________________ 13
Start panel ___________________________________________________________________________ 13
Remote control ________________________________________________________________________ 16
Using the Kill Switch function - MOB _______________________________________________________ 18
Using the Tilt and Trim function ___________________________________________________________ 19
Changing your PIN code _________________________________________________________________ 19
Pairing a new or extra remote control ______________________________________________________ 20
Maintenance___________________________________________________________________________ 21
Replacing the battery on the remote control _________________________________________________ 21
Before calling for support________________________________________________________________ 22
6
OXE DIESEL COASTKEY MANUAL
OVERVIEW
OVERVIEW
Fig. 1 CoastKey wireless kill switch system components - single configuration
The CoastKey system consists of a remote control (1),a start panel (2), motor module(s) (3), and adapter
harness(es) (4).
TECHNICAL DATA
Remote control
Dimensions (D x H): 50 x 12 mm
Weight: 42 g
Battery: CR2032 3 V lithium metal coin cell battery
Battery life: Up to 2 years (700 - 800 hours of motor operating time)
IP class: 67
Start panel
Dimensions (D x H): 65 x 63 mm
Weight: 75 g
Power supply: 12 V
IP class: 66
Power consumption:
- 1.7 mA at main power on and ignition off
- 0 mA at main power off
7
OXE DIESEL COASTKEY MANUAL
OVERVIEW
Motor controller (single)
Dimensions (L x W x H): 130 x 65 x 50 mm
Weight: 180 g
Power supply: 12 V
IP class: 67
Power consumption:
- 0.3 mA at main power on and ignition off
- 0 mA at main power off
Motor controller (twin)
Dimensions (L x W x H): 130 x 65 x 50 mm
Weight: 250 g
Power supply: 12 V
IP class: 67
Power consumption:
- 0.6 mA at main power on and ignition off
- 0 mA at main power off
General data
- Radio frequency: 2.4 GHz
- Temperature range: -25C to + 60C
- Range: 6 - 10 meters
NOTE! The range will depend on your surroundings and where the start panel is placed, so the exact
safety range will vary. It is important that you familiarize yourself with the range aer the system is
installed.
We recommend that you test the safety range on board your boat. This should be done in the open sea
while you move around the boat.
The product is certified according to the following standards:
- Safety: EN 60950-1
- EMC: EN 301 489-17 V3.1.1
- Radio: EN 300 328 V2.1.1
- FCC Part 15.249
- ISED RSS-210
8
OXE DIESEL COASTKEY MANUAL
SAFETY AND WARNINGS
- The system shall be used only on board the vessel and within a radius of 6-10 meters from the steering
position.
- The remote control must always be activated and attached to the captain for the Kill Switch function to
work as described.
- If there are several wireless systems on board the vessel, it may affect operating stability. Operating
stability can also be affected by external radio noise conditions.
- Consult your authorized healthcare professional and read the instructions of the manufacturer of any
medical devices before using the product near cardiac stimulators or other similar medical devices.
- The remote control must not be near metal surfaces or carbon during use as this will impair the radio
signal.
- The remote control should only be in water in the event of a real Man Overboard (MOB) situation.
- If the system behaves abnormally, turn off the main power switch immediately and check batteries in the
remote control before restarting.
- The system will only stop the engine(s) if the driver falls overboard and has the remote control attached.
The system will not stop the engine(s) if the driver falls on board the boat.
- The remote control with an attached string will float if it falls into the water. Additional weight attached to
the remote control will cause it to sink.
SAFETY AND WARNINGS
9
OXE DIESEL COASTKEY MANUAL
INSTALLATION
Checklist before installation:
- Read this installation and operation manual before installing the CoastKey system.
- Check that the engine(s) starts and operates normally before installation.
- Do not install the CoastKey system in an explosive environment.
- Do not alter or tamper with the CoastKey system and design.
- Only use the CoastKey for its original purpose and only install as per the directions in this manual.
- Familiarize yourself with the national safety rules and regulations in your region to avoid a breach of these
rules and help prevent accidents.
- Only install the motor controller(s) in areas that are protected against water intrusion.
INSTALLING THE START PANEL
Fig. 2 Start panel dimensions
1. Drill a ø52 mm/2-1/16 in. hole for the start panel and insert.
!WARNING
Do not to drill through any existing cables or equipment mounted or situated on the backside of your
intended position!
2. Secure the start panel by tightening the nut on the back.
INSTALLATION
10
OXE DIESEL COASTKEY MANUAL
CONNECTING THE CABLES
The CoastKey wireless kill switch system can control from one to four motors. Connection of the cable harness
depends on the number of motors.
Fig. 3 One-motor application
The one-motor application uses one cable harness and a single motor controller.
Fig. 4 Two-motor application
The two-motor application uses two cable harnesses and a dual motor controller.
Fig. 5 Three-motor application
The three-motor application uses three cable harnesses and a single motor controller plus a dual motor
controller.
INSTALLATION
Inhaltsverzeichnis
