Ozito LWE-1400 Bedienungsanleitung

Lawn Edger

1400W

Instruction Manual

2 Year Replacement Warranty

LWE-1400

WARNING! Read all safety warnings and all instructions. Failure to follow the

warnings and instructions may result in electric shock, ﬁre and/or serious injury.

Save all warnings and instructions for future reference.

To view the full range visit: www.ozito.com.au

0812

SPECIFICATIONS - MODEL NO. LWE-1400

KNOW YOUR PRODUCT

Motor: 1400W

Voltage: 230-240~50Hz

No load speed: 3600/min

Cutting depths: 15, 25, 38mm

Blade: 190mm x 18mm bore

Noise level: 103dB

Weight: 6.5kg

1. Lock-Off Safety Switch

2. Power-On LED

3. Dual Safety Levers

4. Upper Shaft

5. Telescopic Locking Collar

6. Lower Shaft

7. Motor Housing

8. Depth Adjustment Locking Knob

9. Guide Wheel

10. Cutting Blade

11. Blade Guard

TABLE OF CONTENTS

SPECIFICATIONS ………………………………………..

INTRODUCTION…………………………………………

ELECTRICAL SAFETY…………….………………………

GENERAL POWER TOOL SAFETY WARNINGS………

LAWN EDGER SAFETY WARNINGS ……………........

ASSEMBLY.....................…………………………………

OPERATION………………………………………………

MAINTENANCE…………….……………………………

SPARE PARTS …………….……………………………...

DESCRIPTION OF SYMBOLS ………………………….

PACK CONTENTS ………………………………………

WARRANTY………………………………………………

Page 2

Page 4

Page 5

Page 7

Page 8

Page 9

Page 11

Page 12

Page 13

Page 14

Read and understand the manual prior to operating this tool.

Save these instructions and other documents supplied with this tool for future reference.

The electric motor has been designed for 230V and 240V only. Always check that the

power supply corresponds to the voltage on the rating plate.

Note: The supply of 230V and 240V on Ozito tools are interchangeable for Australia

and New Zealand.

This tool is double insulated in accordance with AS/NZS 60335-1; therefore

no earth wire is required.

If the supply cord is damaged, it must be replaced by a qualiﬁed electrician

or a power tool repairer in order to avoid a hazard.

If operating a power tool in a damp location is unavoidable use a residual current

device (RCD) protected supply. Use of an RCD reduces the risk of electric shock.

Note: Double insulation does not take the place of normal safety precautions when

operating this tool. The insulation system is for added protection against injury

resulting from a possible electrical insulation failure within the tool.

Using an Extension Lead

Always use an approved extension lead suitable for the power input of this tool.

Before use, inspect the extension lead for signs of damage, wear and ageing. Replace

the extension lead if damaged or defective. When using an extension lead on a reel,

always unwind the lead completely. Use of an extension lead not suitable for the

power input of the tool or which is damaged or defective may result in a risk of ﬁre

and electric shock.

Extension cords shall not be lighter than:

- If rubber insulated, ordinary tough rubber sheathed ﬂexible cord (code designation

60245 IEC 53- If polyvinyl chloride insulated, ordinary polyvinyl chloride sheathed

ﬂexible cord (code designation 60227 IEC 53)

INTRODUCTION

Congratulations on purchasing an Ozito Lawn Edger. We aim

to provide quality tools at an affordable price. We hope you

will enjoy using this tool for many years.

Your Ozito Lawn Edger LWE-1400 has been designed to trim

lawn edges along driveways and footpaths as well as general

landscaping tasks in the garden such as shaping borders

around ﬂowerbeds and trees. It is intended for DIY (Do It

Yourself) use only.

ELECTRICAL SAFETY

WARNING! When using mains-powered equipment, basic safety precautions,

including the following, should always be followed to reduce risk of ﬁre,

electric shock, personal injury and material damage.

1) Work area safety

a) Keep work area clean and well lit. Cluttered or dark areas invite accidents.

b) Do not operate power tools in explosive atmospheres, such as in the

presence of ﬂammable liquids, gases or dust. Power tools create sparks which

may ignite the dust or fumes.

c) Keep children and bystanders away while operating a power tool. Distractions

can cause you to lose control.

2) Electrical safety

a) Power tool plugs must match the outlet. Never modify the plug in any

way. Do not use any adapter plugs with earthed (grounded) power tools.

Unmodiﬁed plugs and matching outlets will reduce risk of electric shock.

b) Avoid body contact with earthed or grounded surfaces, such as pipes,

radiators, ranges and refrigerators. There is an increased risk of electric shock if

your body is earthed or grounded.

c) Do not expose power tools to rain or wet conditions. Water entering a power

tool will increase the risk of electric shock.

d) Do not abuse the cord. Never use the cord for carrying, pulling or unplugging

the power tool. Keep cord away from heat, oil, sharp edges or moving parts.

Damaged or entangled cords increase the risk of electric shock.

e) When operating a power tool outdoors, use an extension cord suitable for

outdoor use. Use of a cord suitable for outdoor use reduces the risk of electric

shock.

f) If operating a power tool in a damp location is unavoidable, use a residual

current device (RCD) protected supply. Use of an RCD reduces the risk of

electric shock.

3) Personal safety

a) Stay alert, watch what you are doing and use common sense when operating

a power tool. Do not use a power tool while you are tired or under the

inﬂuence of drugs, alcohol or medication. A moment of inattention while

operating power tools may result in serious personal injury.

b) Use personal protective equipment. Always wear eye protection. Protective

equipment such as dust mask, non-skid safety shoes, hard hat, or hearing

protection used for appropriate conditions will reduce personal injuries.

c) Prevent unintentional starting. Ensure the switch is in the off-position before

connecting to power source and/or battery pack, picking up or carrying the

tool. Carrying power tools with your ﬁnger on the switch or energising power

tools that have the switch on invites accidents.

WARNING! Read all safety warnings and all instructions. Failure to

follow the warnings and instructions may result in electric shock, ﬁre and/or

serious injury.

Save all warnings and instructions for future reference. The term “power

tool” in all of the warnings refers to your mains-operated (corded) power tool

or battery-operated (cordless) power tool.

GENERAL POWER TOOL SAFETY WARNINGS

d) Remove any adjusting key or wrench before turning the power tool on. A

wrench or a key left attached to a rotating part of the power tool may result in

personal injury.

e) Do not overreach. Keep proper footing and balance at all times. This enables

better control of the power tool in unexpected situations.

f) Dress properly. Do not wear loose clothing or jewellery. Keep your hair,

clothing and gloves away from moving parts. Loose clothes, jewellery or long

hair can be caught in moving parts.

g) If devices are provided for the connection of dust extraction and collection

facilities, ensure these are connected and properly used. Use of dust collection

can reduce dust-related hazards.

4) Power tool use and care

a) Do not force the power tool. Use the correct power tool for your application.

The correct power tool will do the job better and safer at the rate for which it was

designed.

b) Do not use the power tool if the switch does not turn it on and off. Any power

tool that cannot be controlled with the switch is dangerous and must be repaired.

c) Disconnect the plug from the power source and/or the battery pack from the

power tool before making any adjustments, changing accessories, or storing

power tools. Such preventive safety measures reduce the risk of starting the power

tool accidentally.

d) Store idle power tools out of the reach of children and do not allow persons

unfamiliar with the power tool or these instructions to operate the power

tool. Power tools are dangerous in the hands of untrained users.

e) Maintain power tools. Check for misalignment or binding of moving parts,

breakage of parts and any other condition that may affect the power tool’s

operation. If damaged, have the power tool repaired before use. Many

accidents are caused by poorly maintained power tools.

f) Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp

cutting edges are less likely to bind and are easier to control.

g) Use the power tool, accessories and tool bits etc. in accordance with these

instructions, taking into account the working conditions and the work to be

performed. Use of the power tool for operations different from those intended

could result in a hazardous situation.

5) Service

a) Have your power tool serviced by a qualiﬁed repair person using only

identical replacement parts. This will ensure that the safety of the power tool is

maintained.

b) If the supply cord is damaged, it must be replaced by the manufacturer, its

service agent or similarly qualiﬁed persons in order to avoid a hazard.

GENERAL POWER TOOL SAFETY WARNINGS

LAWN EDGER SAFETY WARNINGS

WARNING! – Do not touch rotating parts;

This appliance is not intended for use by persons (including children) with reduced

physical, sensory or mental capabilities, or lack of experience and knowledge, unless

they have been given supervision or instruction concerning use of the appliance by a

person responsible for their safety.

Children should be supervised to ensure that they don’t play with the appliance.

Always wear adequate protective clothing when operating the tool to avoid injuries to

face, eyes, hands, feet, head or hearing.

Use safety glasses or a face shield, high boots or sturdy shoes, long trousers, work

gloves, a hard hat and ear defenders.

Do not start the tool when it is upside down or when it is not in the operating position.

Switch the motor off and remove the plug when the tool is not being used, left

unattended, being cleaned, being moved from one place to another or when the

extension cord is entangled or damaged.

Do not operate the tool near people, especially children or pets. Turn it off if they get too

close. Maintain a safe distance of at least 5m from other people when using the tool.

• Do not expose to moisture

• Do not operate the appliance when barefoot or wearing open toe shoes.

• While operating the appliance, always wear substantial footwear and long trousers.

• Operate the appliance only in daylight or in good artiﬁcial light.

• Avoid operating the appliance in wet grass, where feasible.

• Always be sure of your footing on slopes.

• Walk, never run.

• Always work across the face of slopes, never up and down.

• Exercise extreme caution when changing direction on slopes.

• Do not operate the appliance on excessively steep slopes.

• Use extreme caution when reversing or pulling the appliance towards you.

• Stop the rotating parts if the appliance has to be tilted for transportation. Do not

operate the cutting means when crossing surfaces other than grass, and when

transporting the appliance to and from the working area.

• Never operate the appliance with defective guards or shields, or without safety

devices, for example deﬂectors and/or catchers in place.

• Switch on the motor according to instructions and with feet well away from

rotating parts.

• Do not tilt appliance when switching on the motor, except if the appliance has to

be tilted for starting. In this case, do not tilt it more than absolutely necessary and

lift only the part which is away from the operator. Always ensure that both hands

are in the operating position before returning the appliance to the ground.

• Do not put hands or feet near or under rotating parts.

• For rotary appliances keep clear of the discharge opening at all times.

• Never pick up or carry an appliance while the motor is running.

• Pull the plug from the socket:

- whenever you leave the machine;

- before clearing a blockage;

- before checking, cleaning or working on the appliance;

- if the cord is damaged or entangled;

- after striking a foreign object. Inspect the appliance for damage and make

repairs as necessary.

•Iftheappliancestartstovibrateabnormally,checkimmediately.

ASSEMBLY

Assembling the telecopic shaft to the motor housing

1. Align the grove on the lower shaft (6) with the lug in

the motor housing (7) (Fig. 1). Take care not to damage

the cable while aligning the lower shaft (6).

2. Firmly push the lower shaft (6) into the motor

housing (7) till it locates into place with a “click”.

Tighten the two screws to secure lower shaft (6) in

place (Fig. 2).

3. Align the upper shaft (4) with the lower shaft (6)

ensuring that the spring loaded pin locates with the

slot in the upper shaft (4) (Fig. 3). Take care not to

damage the cable while aligning the shafts.

4. Depress the spring loaded pin as you push the

upper shaft (4) fully into the lower shaft (6) until your

hear a “click”. Take care not to damage the cable while

pushing the shafts together.

5. Slide the telescopic locking collar (5) into place and rotate clockwise to tighten.

Fig. 1

Fig. 3

Fig. 2

WARNING! Before assembly, make sure that the lawn edger is switched

off and unpluged.

Fig. 6

OPERATION

Preparing The Lawn Edger For Use

Telescopic Shaft Adjustment

The lawn edger can be adjusted to suit the height of the operator.

1. Loosen the telescopic locking collar (5) by rotating in a anti-clockwise direction.

2. Adjust the telescopic shaft up or down to the appropriate height. Tighten the

telescopic locking collar (5).

Cutting Depth

The lawn edger provides 3 cutting depths, 15, 25 and 38mm.

1. Loosen the depth adjustment locking knob (8) to

allow you to push the knob enough to move the

guide wheel arm across to the opposite side of

the housing (Fig 4).

2. Raise the guide wheel cutting arm to increase

the depth or lower to decrease the depth. Firmly

tighten the depth adjudstment locking knob (8)

when the guide wheel arm has located into the

desired cutting depth (Fig. 5).

Note: Ensure the lug on the guide wheel arm is

correctly located into the preset depth position on the

motor housing.

Extension Cord Retainer (Fig. 6)

To avoid detaching the extension cord always check

that it is attached to the cord retainer before using the

lawn edger.

1. Make a loop with the extension cord and push it

through the square hole beneath the handle.

2. Place the end of the loop around the cord retainer

and ensure it is pulled ﬁrmly enough to prevent it

from coming loose whilst operating the lawn edger.

3. Connect the extension cord socket to lawn edger cord plug.

WARNING! The lawn edger runs for a few seconds after the switch has

been released. Let the motor come to a complete standstill before setting

the tool down.

Fig. 4

Fig. 5

OPERATION (cont.)

Switching ON

For your safety the lawn edger is designed with a lock-off safety switch (1) and dual

safety levers (3). If only one lever is squeezed, the lawn edger will not operate. This

prevents accidental start up of the lawn edger.

CAUTION: To avoid kickback of the lawn edger, tilt the handle down sufﬁciently so

the blade does not in contact the ground before switching On.

1. To turn the lawn edger On, press the lock-off safety

switch (1) fully down, then squeeze one of the dual

safety levers (3) (Fig. 7).

2. Release the lock-off safety switch (1) and hold both

dual safety levers (3) in to maintain power and

stability to the lawn edger while in use.

Switching OFF

1. To turn the lawn edger Off, simply release the dual safety levers (3).

Edging

1. Before starting , line up the lawn edger cutting

blade (10) with the edge to be cut. Use the arrows

on the blade guard (11) to assist in guiding you

where the cutting blade (10) will cut (Fig. 8).

2. Tilt the handle down so the cutting blade (10) is sufﬁciantly above the ground

before switching On, this is to avoid kickback of the lawn edger when started.

3. Switch on the lawn edger and allow the cutting blade (10) to reach full speed.

Fig. 7

WARNING! The lawn edger runs for a few seconds after it has been

switched off. Let the motor come to a complete standstill before setting

the tool down.

WARNING! Take care that the work area is free of rocks, debris, lines and

other foreighn objects.

Fig. 8

Inhaltsverzeichnis

Andere Ozito Rasenmäher Handbücher

Ozito

Ozito PowerXChange PXCBLTLMC-218 Bedienungsanleitung

Ozito

Ozito ELM-140 Bedienungsanleitung

Ozito

Ozito Power X Change PXCLES-018 Bedienungsanleitung

Ozito

Ozito Power X Change PXCLMK-218E Bedienungsanleitung

Ozito

Ozito PXCLMS-018 Bedienungsanleitung

Ozito

Ozito PXCSDMK-418U Bedienungsanleitung

Ozito

Ozito Ecomow ECO-320 Bedienungsanleitung

Ozito

Ozito XU1 XLMS-018 Bedienungsanleitung

Ozito

Ozito ELM-1545 Bedienungsanleitung

Ozito

Ozito ECOMOW ELM-1536 Bedienungsanleitung

Ozito

Ozito PXCLMK-018 Bedienungsanleitung

Ozito

Ozito ELM-1000 Bedienungsanleitung

Ozito

Ozito ELM-1800 Bedienungsanleitung

Ozito

Ozito ELM-300 Bedienungsanleitung

Ozito

Ozito Power X Change PXCLMK-418 Bedienungsanleitung

Ozito

Ozito PXCLMK-218EU Bedienungsanleitung

Ozito

Ozito ELM-1230 Bedienungsanleitung

Ozito

Ozito Power X Change PXBSDMS-0182 Bedienungsanleitung

Ozito

Ozito PXCSDMS-018 Bedienungsanleitung

Ozito

Ozito PXLMS-335 Bedienungsanleitung

Ozito

Ozito LMGT-1025 Bedienungsanleitung

Ozito

Ozito PXCLMK-1418 Bedienungsanleitung

Ozito

Ozito LML-036 Bedienungsanleitung

Ozito

Ozito LMP-301 Bedienungsanleitung

Beliebte Rasenmäher Handbücher anderer Marken

RHINO

RHINO 1958 Bedienungsanleitung

Wolf Garten

Wolf Garten Compact plus 40 B Bedienungsanleitung

Cub Cadet

Cub Cadet LTX 1045 Bedienungsanleitung

GGP ITALY SPA

GGP ITALY SPA CR/CS 434 SERIES Bedienungsanleitung

Challenge

Challenge CH18V2 Betriebsanleitung

TALEN TOOLS

TALEN TOOLS AVR HGM30 Bedienungsanleitung

DEWEZE

DEWEZE ATM-725 Bedienungsanleitung

Weed Eater

Weed Eater 180083 Bedienungsanleitung

Husqvarna

Husqvarna Poulan Pro PP185A42 Bedienungsanleitung

Better Outdoor Products

Better Outdoor Products Quick Series Bedienungsanleitung

Cub Cadet

Cub Cadet 23HP Z-Force 60 Betriebsanleitung

MTD

MTD 795, 792, 791, 790 Bedienungsanleitung

Toro

Toro Groundsmaster 3505-D Bedienungsanleitung

Dennis

Dennis FT 610 Bedienungsanleitung

MTD

MTD 126-220-000 Bedienungsanleitung

Toro

Toro 74806 Bedienungsanleitung

Stihl

Stihl RMA 443 PV Bedienungsanleitung

Yard-Man

Yard-Man 3700-0 Bedienungsanleitung