Panasonic FV-15CSD1 Bedienungsanleitung

INSTALLATION AND

OPERATING INSTRUCTIONS

Model No. FV-15CSD1

CONTENTS

SAFETY INSTRUCTIONS ............................ 2

INSTALLATION INSTRUCTIONS ............ 2~3

INSTALLATION REQUESTS.........................3

SUPPLIED ACCESSORIES............................4

PARTS NAME AND DIMENSIONS...............4

HOW TO INSTALL..................................4~5

TEST RUN...................................................6

USE AND MAINTENANCE

INSTRUCTIONS......................................6~7

TROUBLESHOOTING..................................7

FURTHER INFORMATION 7~BACK COVER

SPECIFICATIONS.....................BACK COVER

Warranty card attached

Thank you for purchasing this Panasonic product.

Please read these instructions carefully before attempting to install, operate or service the

Panasonic product. Please carefully read “INSTALLATION INSTRUCTIONS” (P.2~3) of this

instructions before installation. Failure to comply with instructions could result in personal

injury or property damage. Please explain to users how to operate and maintain the product

after installation, and this booklet should be presented to users. Please carefully read

“USE AND MAINTENANCE INSTRUCTIONS” (P.6~7) of this instructions before operation.

Please retain this booklet for future reference.

Make sure that the correct information is written on the warranty card, including the date

of purchase and the name of the distributor. Keep the warranty card in a safe place along

with the instructions for future reference.

Nanoe Generator

SAFETY INSTRUCTIONS Please observe strictly

This product is not intended for use by persons (including children) with reduced

physical, sensory or mental capabilities, or lack of experience and knowledge, unless

they have been given supervision or instruction concerning use of the product by a

person responsible for the safety. Children should be supervised to ensure that they

do not play with the product.

Disconnect power supply before maintenance.

The degrees of injury or damage that can occur when the instructions are ignored and if the

product is not used properly have been classified and described by the following indications.

The following instructions should be strictly observed in order to prevent injury to the users

and other people, or damage to property.

This indication means: Must be treated seriously that this

may result in death or serious injury.

WARNING

This indication means: Must be treated seriously that this

may result in injury or physical damage.

CAUTION

This symbol indicates the item is “PROHIBITED” to do.

This symbol indicates the “COMPULSORY” item that must be

followed without failure.

This symbol indicates the item is “CAUTION”.

Types of instructions that should be observed have been classified and described by the

following pictorial symbols.

INSTALLATION INSTRUCTIONS

Don’t install the product with the

method which is not approved in

the instructions.

Otherwise, unreliable installation

may be caused and thus the

product may fall off, resulting in

injuries.

Don’t operate the product other than

the rated voltage (220 V-240 V~ 50 Hz).

Otherwise, it may cause damages to

the product or a fire.

The product must be grounded.

Otherwise, it may cause

electric shock when there is

any trouble or electric leakage.

The power cord must be fixed to

lower than cord exit.

Water may flow into product

through the power cord, which

will cause electric shock or result

in fire.

If the supply cord is damaged, it must be replaced by a special cord or assem-

bly available from the manufacturer or its service agent.

Otherwise, it may cause a short

circuit, thus resulting a fire.

Please install an all-pole switch which

the contact separation is more than

3 mm to control the power of the

product.

WARNING

CAUTION

INSTALLATION INSTRUCTIONS

Do not reconstruct this product.

Otherwise, it may cause damage

to the product.

Installation regulation concerning

local requirement should be fulfilled.

This may damage the product’s

structure and decrease its safety.

Components must be installed

tightly.

Product must be installed tightly.

Otherwise, components may fall

off to cause personal injury.

Otherwise, product may fall

off to cause personal injury.

Otherwise, product may fall off to

cause personal injury.

Do not install the product on the

window or wall.

This product must be installed by

qualified technician.

Improper installation may cause

the product to fall off.

Otherwise, short circuit

may result in fire.

Do not install the product where is

exposed to oil mist.

INSTALLATION REQUESTS

Do not install the product in

places with high temperature.

Otherwise, it may

cause the product

deformation or the

motor life shorten. Within

50 cm

Ambient

temperature

above 40 °C

Do not install product on a

slanting ceiling.

Otherwise, it may cause

the product abnormal.

Otherwise, it may cause the product

abnormal.

Do not install product where is exposed

to humidity.

Install the product at the position as

the figure show below.

Otherwise, it may cause the wall dirty.

Above 150 mm

Suggest to install the product over

1.5 m apart from the vent.

Otherwise, it may affect the

performance of the product.

Use a wall switch (supply on market)

as the power switch for product

(Turning ON/OFF to control the product).

Install the product over 1.5 m apart from the fire annunciator. Otherwise it may

cause false action of the fire annunciator. For detail, please confirm the fire

annunciator instructions.

LED Light (Blue)

Limiting

Screw

SUPPLIED ACCESSORIES

The following accessories are provided with the product in the package. When you unpack,

check if the accessories are all included. If not, please contact your dealer.

Drawing

No.

Installation and operating instructions

Name

Warranty card

PARTS NAME AND DIMENSIONS

Unit: mm

When install

plate open

No. Qty

Qty

Part name

Louver

Electric Case Assy

Frame

Motor

Orifice Assy

Fan

nanoeTM X unit

Install Plate

Power plug

Install Screw

※Initial position of install plate

is closed.

HOW TO INSTALL

1Take off the limiting screw, turn the

louver along the arrow to take it out.

Turn

2Ensure each install plate is at the

initial position (shown as below) and

insert product into ceiling inclined.

Install hole

Install plate

Install hole

Power cord

Ceiling

HOW TO INSTALL

Turn

Turn the install screw of product

clockwise till the install plate clamping

to ceiling.

Frame

Ceiling

Install

plate

Product

Notice

Ensure the tighten torque in the range

of 60 cN.m to 120 cN.m. Product may

fall off when torque not enough,

may damage when torque too large.

Find the “▽” mark on louver, place

louver to product aligning the “▽”

to “△“ on product.

Louver

Turn the louveruntil “▽”align to “ ”

of product and it sounds “Da” means

locked. Notice

Ensure the tighten

torque in the range

of 20 cN.m to 40 cN.m.

Product may fall off

when torque not

enough, may damage

when torque too large.

Fix the limiting screw.

CAUTION

Keep the louver close to the ceiling.

Parts may fall off and result in injury.

Do not inspect and maintain the

product by unqualified persons.

TEST RUN

USE AND MAINTENANCE INSTRUCTIONS

Does the fan rotate?

Does the blue LED light light?

Does it have abnormal vibration or noise?

Please check the following items by test run after connecting power.

WARNING

Otherwise, it may cause electric

shock or personal injury.

Before touching the product, ensure

that the power switch is turned off.

Otherwise, it may result in electric

shock.

The fan may rotate even when power

supply is switched off. Please make sure

the fan has been stopped before

inspection.

Otherwise, it may cause injury if finger

or object is caught into the rotating

section.

Once flammable gas leaks, do not

start any function of this product.

Otherwise, it may generate spark

and thus lead to explosion.

Do not spray or clean this product

directly with water or other liquid.

Otherwise, it may cause short

circuit or electric shock.

If you will not use this product any more,

remove the product.

This product may cause injuries once

it falls off.

Do not disassemble this product for

repair or reconstruction.

Doing this may lead to fire and

electric shock.

CAUTION

When you check or clean the product,

please wear gloves.

Otherwise, it may result in personal

injury.

Do not insert the finger to the louver

gap when cleaning the louver.

Otherwise, it may result in personal

injury.

Notice

3. Do not use petrol, benzene, thinner or any other such alkaline detergent for cleaning the

product.

1. According to the condition of using environment, routine maintenance is required at least

once a year.

2. Do not immerse blade or other resin parts in hot water over 60 °C.

petrol

thinner

benzene

Alkaline

detergent

Clean the dust on surface of louver with a cloth adding neutral cleanser, and then dry

the louver with a soft dry cloth.

Do not insert the finger or

rarity into the nanoeTM X exit.

Otherwise, it may cause short

circuit or electric shock.

nanoeTM X exit

TROUBLESHOOTING

USE AND MAINTENANCE INSTRUCTIONS

Check the product according to the table below if a fault occurs. If the error still occurs,

disconnect all-poles switch of the product, and contact your dealer.

Symptom Cause Troubleshooting

·Fan doesn’t rotate

·No wind blows out

·Running LED light

(blue) doesn’t light

Switch is off

Incorrect wiring

Turn the switch on

Contact your dealer

Smells peculiarly

When nanoeTM X is generated,

small amount of ozone will

be release. However, it will

be not harmful to human beings

It is the performance when

product is normally running,

not function abnormal

Sounds "zi" lightly

around the orifice

The sound comes with nanoeTM X

generating. It is hard to detect

It is the performance when

product is normally running,

not function abnormal

LED light (blue)

blinks The product is in abnormal Contact your dealer

Abnormal shaking

or noise

Failure installation of louver

or product abnormal Contact your dealer

FURTHER INFORMATION (About nanoe

Room temperature: About 5 °C~40 °C (dew-point temperature: more than 2 °C)

Relative humidity: About 30%~85%

Generating environment

nanoeTM X is generated using the air in the room and hence, depending on the temperature

and humidity, there can be incidences whereby nanoeTM X is not stably generated.

Conditions for generated

Small amount of ozone will be generated

When nanoeTM X ion is generated, small amount of ozone will be release. However, the

quantity will be less than the usual level in forest or natural environment, and not

harmful to human beings.

The so-called nanoe™ X are particulate ions containing hydroxyl

radicals whose amount is 10 times that of nanoe™.

nanoe™ X are charged water purification particles generated by

applying high voltage to separate water molecules.

nanoe™ X features: high moisture content, small particles, stability.

1. High moisture content (the moisture content is 1,000 times the moisture content of

ordinary anions)

2. Small particles (about 5 nm - 20 nm in size)

3. Stability (nanoe™ X has a 6 times higher stability than an ordinary anions, with a 10-meter

or longer range of coverage)

4. High OH hydroxyl amount (up to 4,800 billion of OH ions are generated per second)

5. Weak acidity (with weak acidity features close to that of hair and skin)

FURTHER INFORMATION (About nanoe

About nanoeTM

SPECIFICATIONS

Rated

Voltage

[V]

220 50

230 50

240 50

4.0

23.5

25.5

1.3

Rated

Frequency

[Hz]

Power

Consumption

[W]

Air Volume

[m3/h]

Noise

[dB(A)]

Net weight

[kg]

Value of power consumption, Air volume and noise are measured when the static

pressure is 0 Pa.

Air volume is the central value measured by this company with a range of ±10% tolerance.

Noise is the A weighted sound pressure level, which is the central value measured by this

company, its tolerance range is from +3 dB to -7 dB. The method to measure is as follows:

in an anechoic chamber, measure noise value 1 m away from the front, left and beneath

of the product, then get the average value.

This product comply with the IPX2 requirement against the water drop experiment.

The applicable ambient temperature of this product is in the range of -10 °C~40 °C,

using it out of this range may cause a fault.

However, please see page 7 for the generating environment of nanoe.

The above specification may be changed without prior notice.

Note: nanoeTM and the nanoeTM mark are trademarks of Panasonic Corporation.

Panasonic Corporation

Web Site: http://www.panasonic.com

P0621-0 15CSD1401

Issue date: 06/2021

Andere Handbücher für FV-15CSD1

Inhaltsverzeichnis

Andere Panasonic Luftreiniger Handbücher

Panasonic

Panasonic F-PXV50A Bedienungsanleitung

Panasonic

Panasonic F-VR401 Bedienungsanleitung

Panasonic

Panasonic EH3012 - AIR PURIFIER-PHCC Bedienungsanleitung

Panasonic

Panasonic F-VXL40H Bedienungsanleitung

Panasonic

Panasonic F-PXH55H Bedienungsanleitung

Panasonic

Panasonic F-PXM55A Bedienungsanleitung

Panasonic

Panasonic F-PXV35H Bedienungsanleitung

Panasonic

Panasonic F-P16X8C-ES Bedienungsanleitung

Panasonic

Panasonic F-VXK70A Bedienungsanleitung

Panasonic

Panasonic F-PXV35M Bedienungsanleitung

Panasonic

Panasonic F-VXH50A Bedienungsanleitung

Panasonic

Panasonic F-P04DXZ Bedienungsanleitung

Panasonic

Panasonic EH3020 - AIR PURIFIER-PHCC Bedienungsanleitung

Panasonic

Panasonic F-VXL95M Bedienungsanleitung

Panasonic

Panasonic FP15HU2 Bedienungsanleitung

Panasonic

Panasonic nanoeX F-GPT01A Bedienungsanleitung

Panasonic

Panasonic F-VXR70H Bedienungsanleitung

Panasonic

Panasonic Ziaino F-JPT70H Bedienungsanleitung

Panasonic

Panasonic F-PXT175H Bedienungsanleitung

Panasonic

Panasonic F-PXU70A Bedienungsanleitung

Panasonic

Panasonic HEPA Logic EH3020 Bedienungsanleitung

Panasonic

Panasonic F-PXL45H Bedienungsanleitung

Panasonic

Panasonic F-PXM55H Bedienungsanleitung

Panasonic

Panasonic F-YAR25H Bedienungsanleitung

Beliebte Luftreiniger Handbücher anderer Marken

IKEA

IKEA UPPÅTVIND Bedienungsanleitung

Nash

Nash AP-1 PureSmart Bedienungsanleitung

LG PH-U450 Series Bedienungsanleitung

DeLonghi

DeLonghi DDSX 220WFA Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric MA-E85R-E Bedienungsanleitung

Sharp

Sharp FU-40SE Bedienungsanleitung

Philips

Philips AC2721 Bedienungsanleitung

Hitachi

Hitachi EP-A3000 Bedienungsanleitung

TruSens

TruSens Z-2000 Bedienungsanleitung

Motorola

Motorola MBP87SN Bedienungsanleitung

Beko

Beko ATP 7100I Bedienungsanleitung

Carrier

Carrier INFINITY 1620 Bedienungsanleitung

AtmosAir

AtmosAir P2002 Bedienungsanleitung

Winix

Winix NK300 Bedienungsanleitung

Friedrich

Friedrich C-90A Bedienungs- und Montageanleitung

Surgically Clean Air

Surgically Clean Air JADE2.0 Bedienungsanleitung

Base aire

Base aire 555 Pro Bedienungsanleitung

Champion

Champion CP25 Bedienungsanleitung