Panasonic AJ-YAC960P Bedienungsanleitung

SDTI Interface Board

AJ- P

Installation Guide

ENGLISH

DEUTSCHFRANÇAISITALIANOESPAÑOL

Connector area

Serial digital input connectors (BNC x 2)

1Input : Used for both SDTI and SDI signals

2Active through output

Serial digital output connectors (BNC x 3)

3Output 1 : Used for both SDTI and SDI signals

4Output 2 : Used exclusively for SDI signals

5Output 3 : Used exclusively for SDI signals

E-1

SERIAL IN SERIAL OUT

1Input connector used for

both SDTI and SDI signals

2 Active through output

connector

4 Output connector used

exclusively for SDI signals

5 Output connector used

exclusively for SDI signals

3 Output connector used for

both SDTI and SDI signals

SDTI Interface Board

Introduction

AJ-YAC960P

The AJ-YAC960P is an SDTI interface board designed to be used with the AJ-D960. By installing it in the AJ-

D960, digital data can be input and output using the SDTI format*1(compression digital interface).

*1: SDTI (serial data transport interface) complies with the SMPTE 305M standard.

The format of the data streams sent using the SDTI interface complies with the SMPTE 321M standard.

Refer the installation of the SDTI interface board to qualified service personnel. The VTR’s software may

need to be upgraded or its hardware changed.

SDI board

Coin screws

Metal board clamp

Cable clamper

Check that the power of the VTR is off.

Remove the two coin screws, and take off the top panel

from the main unit.

E-2

Remove the screw, and remove the metal board clamp together with the screw. (This screw cannot be

removed from the clamp.)

Detach the cable clamper which is attached to the SDI board.

4. Remove the board (SDI board) inserted at the position marked “F4

”

on the main unit side.

(Do not disconnect the coaxial cables which are connected to the SDI board.)

SDTI Interface Board

Installation

Screw

ENGLISH

Remove the five screws attached to the

spacers on the SDTI board.

Attach the two flat cables supplied in the same

package as the SDTI board to the connectors on

the SDTI board.

Open the connector covers, insert the flat cables

so that the blue stickers are positioned on the top

surface, and then close the covers.

Attach the power cable attached to the SDTI board to the connector on the SDI board.

E-3

SDTI Interface Board

Flat cables

Blue stickers

Covers

SDTI board

Screws (x5)

SDI board

Power cable

SDTI board

Disconnect the coaxial cable with the orange end from the SDI board, and connect it to the connector

located at the position on the SDTI board shown in the figure below.

Follow the steps below to attach the SDTI board to the SDI board.

1 Position spacer 1 and spacer 2 at the holes on the SDI board.

10.

E-4

2 Position spacer 3 at the hole on the SDI board.

SDTI Interface Board

Orange end

of cable

Spacer 2

Spacer 1

Spacer 3

SDI board

SDTI board

Spacer 2Spacer 1

SDI board

SDTI board

Spacer 3

ENGLISH

E-

3 Attach the SDTI board to the SDI board in such a way that the connectors on the SDI board and

SDTI board are fitted precisely together.

4 Use the five screws removed in step 6 to attach the SDTI board to the SDI board.

<Notes>

≥ Wedge the excess length of the power cable between the SDTI board and SDI board.

≥ When installing the screws, take care not to drop them inside the VTR.

SDTI Interface Board

SDI board

SDTI board

Screws (x5)

Fit the connectors together here.

E-

SDTI Interface Board

Insert the SDI board at the position marked “F4” on the main unit side.

Following the same procedure as in step 7, attach the two flat cables to the connectors on the F5 board,

and wedge the excess lengths of these cables between the F5 and F6 boards.

12.

Insert the coaxial cables between the F4 and F5 boards.

13.

Install the metal board clamp using the screw for this purpose, and secure the top panel to the main unit

using the two coin screws.

14.

11.

F6 board

(F4) SDI and SDTI boards

F5 board

F6 board

(F4) SDI and SDTI boards

F5 board

Metal board clamp Screw

ENGLISH

E-7

Specifications

GENERAL

Weight: 170 g

Dimensions: 230 (W) x 113 (H) x 20 (D) mm

VIDEO INPUT

Serial digital input: BNC x 2

SERIAL IN: Used for both SDI/SDTI inputs

Active through output

SDI: Complies with SMPTE 259M-C standard

SDTI: Complies with SMPTE 305M/SMPTE 321M standards

VIDEO OUTPUT

Serial digital output: BNC x 3

SERIAL OUT 1: Used for both SDI/SDTI outputs

SERIAL OUT 2, 3: Used exclusively for SDI output (standard accessories)

SDI: Complies with SMPTE 259M-C standard

SDTI: Complies with SMPTE 305M/SMPTE 321M standards

AUDIO INPUT

Serial digital input: Complies with SMPTE 259M-C/SMPTE 272M-A standards

AUDIO OUTPUT

Serial digital output: Complies with SMPTE 259M-C/SMPTE 272M-A standards

* As with the video input/output, SDTI audio input/output complies with the SMPTE 305M/321M standards.

Weight and dimensions shown are approximate.

Specifications are subject to change without notice.

SDTI Interface Board

E-8

SDTI Interface Board

ENGLISH

Anschlussbereich

Serielle Digitaleingänge (BNC x 2)

1 Eingang : Wird für SDTI- und SDI-Signale verwendet

2 Aktiver Durchschaltungsausgang

Serielle Digitalausgänge (BNC x 3)

3 Ausgang 1 : Wird für SDTI- und SDI-Signale verwendet

4 Ausgang 2 : Wird ausschließlich für SDI-Signale verwendet

5 Ausgang 3 : Wird ausschließlich für SDI-Signale verwendet

D-1

SERIAL IN SERIAL OUT

1Eingang für SDTI- und

SDI-Signale

2Aktiver

Durchschaltungsausgang

4Ausgang nur für

SDI-Signale

5Ausgang nur für

SDI-Signale

3Ausgang für SDTI-

und SDI-Signale

SDTI-Schnittstellenkarte

Einleitung

AJ-YAC960P

Beim Modell AJ-YAC960P handelt es sich um eine SDTI-Schnittstellenkarte, die für den Einsatz mit dem AJ-

D960 vorgesehen ist. Beim Modell AJ-YAC960P handelt es sich um eine SDTI-Schnittstellenkarte, die für den

Einsatz mit dem AJ-D960 vorgesehen ist.

Durch den Einbau der Karte in den AJ-D960 ist es möglich, digitale Daten im SDTI-Format*1ein- und

auszugeben (digitale Komprimierungs-Schnittstelle).

*1: SDTI (Serial Data Transport Interface) entspricht der Norm SMPTE 305M.

Das Format der durch die SDTI-Schnittstelle übertragenen Datenflüsse entspricht der Norm SMPTE 321M.

Überlassen Sie den Einbau der SDTI-Schnittstellenkarte qualifiziertem Wartungspersonal. Eine

Aktualisierung der Videorecorder-Software oder eine Änderung an seiner Hardware ist möglicherweise

notwendig.

Inhaltsverzeichnis

Sprachen:

Andere Panasonic Audio- und Videozubehör Handbücher

Panasonic

Panasonic AW-PH350P Bedienungsanleitung

Panasonic

Panasonic AJ-YA455P Bedienungsanleitung

Panasonic

Panasonic DMP-BD60 - Blu-Ray Disc Player Bedienungsanleitung

Beliebte Audio- und Videozubehör Handbücher anderer Marken

enerserve

enerserve e.manager nD Bedienungsanleitung

Starmatrix

Starmatrix Clever-Pool/220V Betriebsanleitung

TecnoVideo

TecnoVideo VSPT Series Bedienungsanleitung

NeoVolta

NeoVolta NV14 Gebrauchsanweisung

Horizon Fuel Cell

Horizon Fuel Cell FCJJ-40 Bedienungsanleitung

SC&T

SC&T CD108HD Bedienungsanleitung

4-noks

4-noks PR-SA Kurzanleitung

PROAIM

PROAIM CINEMA Series Bedienungsanleitung

Synergistic Research

Synergistic Research UEF ACOUSTIC DOTS Bedienungsanleitung

Paso

Paso C571/6-V Bedienungsanleitung

CMD

CMD bs6396 Bedienungsanleitung

Bluetti

Bluetti EP600 Bedienungsanleitung

Delta Electronics

Delta Electronics AFE075A43A Bedienungsanleitung

Yamaha

Yamaha PTB-4210 Bedienungsanleitung

Burst Electronics

Burst Electronics MCG-2 Bedienungsanleitung

mind alive

mind alive Smart Bedienungsanleitung

MagniLink

MagniLink S PREMIUM 2 MLS-HD-2 Bedienungsanleitung

P3 International

P3 International Kill A Watt Bedienungsanleitung