Panasonic Lumix H-PS14042 Bedienungsanleitung

Before use, please read these instructions completely.

VQT3S52

Operating Instructions

INTERCHANGEABLE LENS FOR DIGITAL CAMERA

Model No. H-PS14042

until

2011/10/3

VQT3S52_E.book 1 ページ２０１１年９月１２日　月曜日　午後１時３８分

VQT3S52

Contents

Information for Your Safety..................................... 2

Precautions........................................................... 4

Supplied Accessories ............................................. 5

Attaching/Detaching the Lens................................. 5

Names and Functions of Components ................... 7

Cautions for Use..................................................... 8

Troubleshooting .................................................. 10

Specifications........................................................ 11

Information for Your Safety

Keep the unit as far away as possible from

electromagnetic equipment (such as microwave

ovens, TVs, video games, radio transmitters,

high-voltage lines etc.).

≥Do not use the camera near cell phones because

doing so may result in noise adversely affecting

the pictures and sound.

≥If the camera is adversely affected by

electromagnetic equipment and stops functioning

properly, turn the camera off and remove the

battery and/or the connected AC adaptor. Then

reinsert the battery and/or reconnect the AC

adaptor and turn the camera on.

The lens can be used with a digital camera

compatible with the lens mount standard for the

“Micro Four ThirdsTM System”.

≥It cannot be mounted on the Four ThirdsTM mount

specification camera.

≥The digital camera illustrations in these operating

instructions show DMC-GF3 as an example.

≥

The appearance and specifications of products described

in this manual may differ from the actual products you

have purchased due to later enhancements.

≥

Micro Four Thirds

and Micro Four Thirds Logo

marks are trademarks or registered trademarks of

Olympus Imaging Corporation, in Japan, the United

States, the European Union and other countries.

≥Four ThirdsTM and Four Thirds Logo marks are

trademarks or registered trademarks of Olympus

Imaging Corporation, in Japan, the United States,

the European Union and other countries.

≥G MICRO SYSTEM is a lens exchange type

digital camera system of LUMIX based on a Micro

Four Thirds System standard.

≥Other names of systems and products mentioned

in these instructions are usually the registered

trademarks or trademarks of the manufacturers

who developed the system or product concerned.

VQT3S52_E.book 2 ページ２０１１年８月３０日　火曜日　午後５時５５分

VQT3S52

-If you see this symbol-

Information on Disposal for Users of Waste Electrical & Electronic Equipment (private

households)

This symbol on the products and/or accompanying documents means that used

electrical and electronic products should not be mixed with general household waste.

For proper treatment, recovery and recycling, please take these products to

designated collection points, where they will be accepted on a free of charge basis.

Alternatively, in some countries you may be able to return your products to your local

retailer upon the purchase of an equivalent new product.

Disposing of this product correctly will help to save valuable resources and prevent

any potential negative effects on human health and the environment which could

otherwise arise from inappropriate waste handling. Please contact your local authority

for further details of your nearest designated collection point.

Penalties may be applicable for incorrect disposal of this waste, in accordance with national legislation.

For business users in the European Union

If you wish to discard electrical and electronic equipment, please contact your dealer or supplier for

further information.

Information on Disposal in other Countries outside the European Union

This symbol is only valid in the European Union.

If you wish to discard this product, please contact your local authorities or dealer and ask for the correct

method of disposal.

ENGLISH

VQT3S52_E.book 3 ページ２０１１年８月３０日　火曜日　午後５時５５分

VQT3S52

∫Lens Care

≥Sand and dust can damage the lens. Make

sure that no sand or dust gets inside the lens

or the terminals when using the lens on a

beach, etc.

≥This lens is not waterproof. If drops of water

get onto the lens, wipe the lens with a dry

cloth.

≥Do not press the lens with excessive force.

≥When there is dirt (water, oil, and fingerprints, etc.)

on the surface of the lens, the picture may be

affected. Lightly wipe the surface of the lens with a

soft, dry cloth before and after taking pictures.

≥Do not place the lens mount facing downwards.

Do not allow the lens contact points 1to become

dirty.

∫About Condensation

(Fogging of the Lens)

≥Condensation occurs when there are differences

in temperature and humidity as described below.

Condensation can cause the lens to become dirty

and lead to mold and malfunctioning, so exercise

caution in the following situations:

– When the camera is brought indoors from outside

during cold weather

– When the camera is brought into an air-

conditioned car

– When cold air from an air conditioner is directly

blown onto the lens

– In humid places

≥Put the camera into a plastic bag to allow it to

acclimatize to the surrounding temperature in

order to prevent condensation. If condensation

occurs, turn the power off and leave it for about

two hours. Once the camera acclimatizes to the

surrounding temperature the condensation will go

away naturally.

Precautions

VQT3S52_E.book 4 ページ２０１１年８月３０日　火曜日　午後５時５５分

VQT3S52

Supplied Accessories

[Inspection to be performed when you unpack

the unit]

When removing the unit from its packing box, check

that the main unit and the supplied accessories are

there and also check their external appearance and

functions to verify that they have not sustained any

damage during distribution and transportation.

If you discover any trouble, contact your vendor

before using the product.

Product numbers correct as of September 2011.

These may be subject to change.

1Lens Storage Bag

2Lens Cap

3Lens Rear Cap

(The lens rear cap and lens cap are attached to

the interchangeable lens at the time of purchase.)

Attaching/Detaching the Lens

≥Refer also to the camera’s operating instructions

for attaching and detaching the lens.

∫Attaching the Lens

≥Check that the camera is turned off.

1 Turn the lens rear cap

to detach it.

A: Lens Rear Cap

Align the lens fitting

marks

(red marks)

the camera body and the

lens and then rotate the

lens in the direction of

the arrow until it clicks.

• Do not press the lens

release button C when you

attach a lens.

• Do not try to attach the lens when holding it at an

angle to the camera body as the lens mount may

get scratched.

• Check that the lens is attached correctly.

VFC4460 VYF3443

123

VFC4605







VQT3S52_E.book 5 ページ２０１１年８月３０日　火曜日　午後５時５５分

VQT3S52

∫Detaching the Lens

≥To protect the lens, turn off the power of the digital

camera and confirm that the lens barrel is

recessed.

While pressing on the

lens release button D,

rotate the lens toward

the arrow until it stops

and then remove.

• Attach the lens rear cap so

that the lens contact point

does not get scratched.

• Attach the body cap to the camera so no dirt or

dust will get inside the main unit.

∫Attaching and

Detaching the Lens Cap

Pinch the lens cap as

shown in the figure to

attach or detach.

• Be careful not to lose the

lens cap.

∫Attaching Filters

≥Attach or detach the filter when the lens barrel is

recessed.

≥Vignetting may occur if using 2 or more

MC protectors (optional: DMW-LMCH37),

PL filters (optional: DMW-LPL37) or ND filters

(optional: DMW-LND37), or if using thick

protectors and/or filters.

≥The filter may become impossible to remove if

excessively tightened, so please refrain from

tightening it too strongly.

≥It is possible to attach the lens cap with the filter

already attached.

≥You cannot attach a conversion lens or adaptor to

this lens. (As of September 2011) A filter may be

used, but attaching any other element may cause

damage to the lens.



VQT3S52_E.book 6 ページ２０１１年８月３０日　火曜日　午後５時５５分

VQT3S52

Names and Functions of

Components

1Lens surface

2Zoom lever

Move the zoom lever to the [T]

(Tele side) or [W] (Wide side).

[T]: To make subjects appear

closer use (Tele)

[W]: To make subjects appear

further away use (Wide)

• The zoom speed varies depending on the

range over which the zoom lever is moved.

Zoom speed will be slower than normal when

recording a motion picture.

3Focus lever

Move the Focus lever to the Aor

A: Focus on the subject close

B: Focus on the subject far

away

• Speed to focus will change depending on the

amount moved.

4Contact points

5Lens fitting mark

VQT3S52_E.book 7 ページ２０１１年８月３０日　火曜日　午後５時５５分

VQT3S52

Note

≥Sound of lever returning may be recorded when

your finger is taken off from the focus lever or

zoom lever while recording a motion picture. Move

the lever quietly when returning to the original

position.

≥When flash recording with a close subject, the

light of the flash will be blocked by the lens and

part of the picture may be dark. Check the

distance from the subject when recording.

≥There is no indication of focal length on the lens.

The focal length is displayed on the screen of the

digital camera when attached to the compatible

digital camera. Focal length is not displayed on

the digital camera that is not compatible. For

details on the digital camera used, refer to the

website.

http://panasonic.jp/support/global/cs/dsc/

(This Site is English only.)

Cautions for Use

Take care not to drop or knock the lens. Also

take care not to put a lot of pressure on the lens.

≥Take care not to drop the bag that you inserted the

lens in as it may strongly shock the lens. The

camera may stop operating normally and pictures

may no longer be recorded. Also, the lens may be

damaged.

When using pesticides and other volatile

substances around the camera make sure that

they do not get onto the lens.

≥

If such substances get onto the lens they can

damage the exterior case or cause the paint to peel.

VQT3S52_E.book 8 ページ２０１１年８月３０日　火曜日　午後５時５５分

VQT3S52

Do not carry the unit when it is still attached to

the camera body.

≥Under no circumstances should the unit be stored

in any of the following locations since doing so

may cause problems in operation or

malfunctioning.

– In direct sunlight or on a beach in summer

– In locations with high temperatures and humidity

levels or where the changes in temperature and

humidity are acute

– In locations with high concentrations of sand,

dust or dirt

– Where there is fire

– Near heaters, air conditioners or humidifiers

– Where water may make the unit wet

– Where there is vibration

– Inside a vehicle

≥Refer also to the operating instructions of the

digital camera.

≥When the unit is not going to be used for a

prolonged period, we recommend storing with a

desiccant (silica gel). Failure to do so may result in

performance failure caused by mold, etc. It is

recommended that you check the unit’s operation

prior to use.

≥Do not leave the lens in contact with rubber or

plastic products for extended periods of time.

≥Do not touch the lens contact point. Doing so can

cause failure of the unit.

≥Do not disassemble or alter the unit.

Do not use benzine, thinner, alcohol or other

similar cleaning agents to clean the lens glass or

exterior cabinet.

≥Using solvents can damage the lens or cause the

paint to peel.

≥Wipe off any dust or fingerprints with a soft, dry

cloth.

≥Do not use a household detergent or a chemically

treated cloth.

VQT3S52_E.book 9 ページ２０１１年８月３０日　火曜日　午後５時５５分

VQT3S52

A sound is heard when the camera is turned on

or off.

≥This is the sound of lens or aperture movement

and is not a malfunction.

When this lens is attached to digital camera,

stabilizer function cannot be turned off or

stabilizer function does not work.

≥The Optical Image Stabilizer function of this lens

only works correctly with supported cameras.

>When older Panasonic digital cameras (DMC-

GF1, DMC-GH1, DMC-G1) are used,

[STABILIZER] in the [REC] mode menu cannot be

set to [OFF]. It is recommended to update the

firmware of the digital camera at the following

website.

http://panasonic.jp/support/global/cs/dsc/

download/

>When using this lens with another make of digital

cameras, the Optical Image Stabilizer function will

not work. (As of September 2011)

For details, contact the respective company.

Troubleshooting

VQT3S52_E.book 10 ページ２０１１年８月３０日　火曜日　午後５時５５分

Andere Handbücher für Lumix H-PS14042

Inhaltsverzeichnis

Sprachen:

Andere Panasonic Kamerazubehör Handbücher

Panasonic

Panasonic AJHVF21G - HD EVF - MULTI-LANG Bedienungsanleitung

Panasonic

Panasonic AW-CH600 Bedienungsanleitung

Panasonic

Panasonic AWPH650N - PAN/TILT HEAD Bedienungsanleitung

Panasonic

Panasonic DMW-MCTZ40 Bedienungsanleitung

Panasonic

Panasonic AJHVF27P Bedienungsanleitung

Panasonic

Panasonic WV-7130D Bedienungsanleitung

Panasonic

Panasonic HFS1442A Bedienungsanleitung

Panasonic

Panasonic HHR160A Bedienungsanleitung

Panasonic

Panasonic WV7110A - MONITOR Bedienungsanleitung

Panasonic

Panasonic Lumix H-VS014140 Bedienungsanleitung

Panasonic

Panasonic LC-XC1238AP Bedienungsanleitung

Panasonic

Panasonic AJ-YBX200G Bedienungsanleitung

Panasonic

Panasonic AJ-BS900P Bedienungsanleitung

Panasonic

Panasonic WV-Q160C Bedienungsanleitung

Panasonic

Panasonic LC-R127R2P Bedienungsanleitung

Panasonic

Panasonic DVCPRO AJ-CA901 Bedienungsanleitung

Panasonic

Panasonic AJ-HVF20P Bedienungsanleitung

Panasonic

Panasonic VIDEOALARM PODV7CPNS Bedienungsanleitung

Panasonic

Panasonic WV-Q118 Bedienungsanleitung

Panasonic

Panasonic WVRM70 - ACCESSORY Bedienungsanleitung

Panasonic

Panasonic H-FSQ 14045 Bedienungsanleitung

Panasonic

Panasonic WV7230 - CCTV ACCESSORIES Bedienungsanleitung

Panasonic

Panasonic BB-HGW700A - Network Camera Router Bedienungsanleitung

Panasonic

Panasonic WVPS104C - CAMERA DRIVE UNIT Bedienungsanleitung

Beliebte Kamerazubehör Handbücher anderer Marken

Viltrox

Viltrox EF-NEX Montageanleitung

Calumet

Calumet 7100 Series CK7114 Bedienungsanleitung

Ropox

Ropox 4Single Series Bedienungsanleitung

Cambo

Cambo Wide DS Digital Series Betriebsanleitung

Samsung

Samsung SHG-120 Bedienungsanleitung

Ryobi

Ryobi BPL-1820 Bedienungsanleitung

Aegis

Aegis ABL-36020P Bedienungsanleitung

Pentax

Pentax Data Back Fc Bedienungsanleitung

Fantasea

Fantasea EyeGrabber F Series Bedienungsanleitung

Honeywell

Honeywell HDZ20HD Bedienungsanleitung

EGO

EGO BA1400T Bedienungsanleitung

Sima

Sima SRW-62 Bedienungsanleitung

Shape

Shape A7SSMKIT Bedienungsanleitung

Slide Kamera

Slide Kamera HST-2 Bedienungsanleitung

Power works

Power works 2902613 Bedienungsanleitung

SES

SES SE-2047-2 Bedienungsanleitung

Olympus

Olympus PT-EP05L Bedienungsanleitung

Starlite

Starlite OctoDome nxt Bedienungsanleitung