Panasonic DC-GH5M Series Bedienungsanleitung

ORDER NO. DSC1703003CE

B26

Digital Camera/Body/Lens Kit

Model No.

DC-GH5P

DC-GH5PP

DC-GH5EB

DC-GH5EC

DC-GH5EE

DC-GH5EF

DC-GH5EG

DC-GH5GA

DC-GH5GC

DC-GH5GD

DC-GH5GH

DC-GH5GK

DC-GH5GN

DC-GH5GT

DC-GH5MEB

DC-GH5MEC

DC-GH5MEF

DC-GH5MEG

DC-GH5LP

DC-GH5LPP

DC-GH5LEB

DC-GH5LEC

DC-GH5LEF

DC-GH5LEG

Page 1 of 2

9/27/2017

file://C:\Users\sh.dehghani\AppData\Local\Temp\Rar$EXa0.129\viewing\SGML_VIEW_...

Colour

Black Type

DC-GH5M series: Interchangeable Lens (H-FS12060) is bundled.

DC-GH5L series: Interchangeable Lens (H-ES12060) is bundled.

DC-GH5A series: Interchangeable Lens (H-HSA12035) is bundled.

DC-GH5LGA

DC-GH5LGK

DC-GH5AGA

Page 2 of 2

9/27/2017

file://C:\Users\sh.dehghani\AppData\Local\Temp\Rar$EXa0.129\viewing\SGML_VIEW_...

1 Safety Precautions

1.1 General Guidelines

1. IMPORTANT SAFETY NOTICE

There are special components used in this equipment which are important for safety. These parts are marked

by in the Schematic Diagrams, Circuit Board Layout, Exploded Views and Replacement Parts List. It is

essential that these critical parts should be replaced with manufacturer’s specified parts to prevent X-

RADIATION, shock, fire, or other hazards. Do not modify the original design without permission of

manufacturer.

2. An Isolation Transformer should always be used during the servicing of AC Adaptor whose chassis is not

isolated from the AC power line. Use a transformer of adequate power rating as this protects the technician from

accidents resulting in personal injury from electrical shocks. It will also protect AC Adaptor from being damaged

by accidental shorting that may occur during servicing.

3. When servicing, observe the original lead dress. If a short circuit is found, replace all parts which have been

overheated or damaged by the short circuit.

4. After servicing, see to it that all the protective devices such as insulation barriers, insulation papers shields are

properly installed.

5. After servicing, make the following leakage current checks to prevent the customer from being exposed to

shock hazards.

1.2 Leakage Current Cold Check

1. Unplug the AC cord and connect a jumper between the two prongs on the plug.

2. Measure the resistance value, with an ohmmeter, between the jumpered AC plug and each exposed metallic

cabinet part on the equipment such as screwheads, connectors, control shafts, etc. When the exposed metallic

part has a return path to the chassis, the reading should be between 1 MΩ and 5.2 MΩ. When the exposed

metal does not have a return path to the chassis, the reading must be infinity.

1.3 Leakage Current Hot Check (See Figure. 1)

1. Plug the AC cord directly into the AC outlet. Do not use an isolation transformer for this check.

2. Connect a 1.5 kΩ, 10 W resistor, in parallel with a 0.15 µF capacitor, between each exposed metallic part on the

set and a good earth ground, as shown in Figure. 1.

3. Use an AC voltmeter, with 1 kΩ/V or more sensitivity, to measure the potential across the resistor.

4. Check each exposed metallic part, and measure the voltage at each point.

5. Reverse the AC plug in the AC outlet and repeat each of the above measurements.

6. The potential at any point should not exceed 0.75 V RMS. A leakage current tester (Simpson Model 229 or

equivalent) may be used to make the hot checks, leakage current must not exceed 1/2 mA. In case a

measurement is outside of the limits specified, there is a possibility of a shock hazard, and the equipment

should be repaired and rechecked before it is returned to the customer.

Page 1 of 2

9/27/2017

file://C:\Users\sh.dehghani\AppData\Local\Temp\Rar$EXa0.129\viewing\SGML_VIEW_...

Figure. 1

Page 2 of 2

9/27/2017

file://C:\Users\sh.dehghani\AppData\Local\Temp\Rar$EXa0.129\viewing\SGML_VIEW_...

2 Warning

2.1 Prevention of Electrostatic Discharge (ESD) to

Electrostatically

Sensitive (ES) Devices

Some semiconductor (solid state) devices can be damaged easily by static electricity. Such components commonly are

called Electrostatically Sensitive (ES) Devices.

The following techniques should be used to help reduce the incidence of component damage caused by electrostatic

discharge (ESD).

1. Immediately before handling any semiconductor component or semiconductor-equipped assembly, drain off any

ESD on your body by touching a known earth ground. Alternatively, obtain and wear a commercially available

discharging ESD wrist strap, which should be removed for potential shock reasons prior to applying power to

the unit under test.

2. After removing an electrical assembly equipped with ES devices, place the assembly on a conductive surface

such as aluminum foil, to prevent electrostatic charge buildup or exposure of the assembly.

3. Use only a grounded-tip soldering iron to solder or unsolder ES devices.

4. Use only an antistatic solder removal device. Some solder removal devices not classified as “antistatic (ESD

protected)” can generate electrical charge sufficient to damage ES devices.

5. Do not use freon-propelled chemicals. These can generate electrical charges sufficient to damage ES devices.

6. Do not remove a replacement ES device from its protective package until immediately before you are ready to

install it. (Most replacement ES devices are packaged with leads electrically shorted together by conductive

foam, aluminum foil or comparable conductive material).

7. Immediately before removing the protective material from the leads of a replacement ES device, touch the

protective material to the chassis or circuit assembly into which the device will be installed.

CAUTION :

Be sure no power is applied to the chassis or circuit, and observe all other safety precautions.

8. Minimize bodily motions when handling unpackaged replacement ES devices. (Otherwise harmless motion such

as the brushing together of your clothes fabric or the lifting of your foot from a carpeted floor can generate static

electricity (ESD) sufficient to damage an ES device).

2.2 How to Recycle the Lithium Ion Battery (U.S.

Only)

Page 1 of 4

9/27/2017

file://C:\Users\sh.dehghani\AppData\Local\Temp\Rar$EXa0.129\viewing\SGML_VIEW_...

2.3 How to Replace the Lithium Battery

2.3.1 Replacement Procedure

1. Remove the TOP UNIT. (Refer to Disassembly Procedures.)

2. Unsolder the each soldering point of electric lead terminal for Lithium battery (Ref. No. “B7501” at bottom side of

TOP UNIT) and remove the Lithium battery together with electric lead terminal. Then replace it into new one.

NOTE:

The Lithium battery includes electric lead terminals.

NOTE:

This Lithium battery is a critical component.

It must never be subjected to excessive heat or discharge.

It must therefore only be fitted in requirement designed specifically for its use.

Replacement batteries must be of same type and manufacture.

They must be fitted in the same manner and location as the original battery, with the correct polarity contacts observed.

Do not attempt to re-charge the old battery or re-use it for any other purpose.

It should be disposed of in waste products destined for burial rather than incineration.

Page 2 of 4

9/27/2017

file://C:\Users\sh.dehghani\AppData\Local\Temp\Rar$EXa0.129\viewing\SGML_VIEW_...

NOTE:

Above caution is applicable for a battery pack which is for DC-GH5/GH5M/GH5L/GH5A series, as well.

2.4 Caution for AC Cord

(For EB/GA/GC/GH)

2.4.1 Information for Your Safety

IMPORTANT

Your attention is drawn to the fact that recording of pre-recorded tapes or discs or other published or broadcast material

may infringe copyright laws.

WARNING

To reduce the risk of fire or shock hazard, do not expose this equipment to rain or moisture.

CAUTION

To reduce the risk of fire or shock hazard and annoying interference, use the recommended accessories only.

FOR YOUR SAFETY

DO NOT REMOVE THE OUTER COVER

To prevent electric shock, do not remove the cover. No user serviceable parts inside. Refer servicing to qualified service

personnel.

2.4.2 Caution for AC Mains Lead

For your safety, please read the following text carefully.

This appliance is supplied with a moulded three-pin mains plug for your safety and convenience.

A 5-ampere fuse is fitted in this plug.

Should the fuse need to be replaced please ensure that the replacement fuse has a rating of 5 amperes and it is approved

by ASTA or BSI to BS1362

Check for the ASTA mark or the BSI mark on the body of the fuse.

If the plug contains a removable fuse cover you must ensure that it is refitted when the fuse is replaced.

If you lose the fuse cover, the plug must not be used until a replacement cover is obtained.

A replacement fuse cover can be purchased from your local Panasonic Dealer.

If the fitted moulded plug is unsuitable for the socket outlet in your home then the fuse should be removed and the plug cut

off and disposed of safety.

There is a danger of severe electrical shock if the cut off plug is inserted into any 13-ampere socket.

If a new plug is to be fitted please observe the wiring code as shown below.

Page 3 of 4

9/27/2017

file://C:\Users\sh.dehghani\AppData\Local\Temp\Rar$EXa0.129\viewing\SGML_VIEW_...

If in any doubt, please consult a qualified electrician.

2.4.2.1 Important

The wires in this mains lead are coloured in accordance with the following code:

As the colours of the wires in the mains lead of this appliance may not correspond with the coloured markings identifying the

terminals in your plug, proceed as follows:

The wire which is coloured BLUE must be connected to the terminal in the plug which is marked with the letter N or coloured

BLACK.

The wire which is coloured BROWN must be connected to the terminal in the plug which is marked with the letter L or

coloured RED.

Under no circumstances should either of these wires be connected to the earth terminal of the three pin plug, marked with

the letter E or the Earth Symbol.

2.4.2.2 Before Use

Remove the Connector Cover as follows.

2.4.2.3 How to Replace the Fuse

1. Remove the Fuse Cover with a screwdriver.

2. Replace the fuse and attach the Fuse cover.

Blue

Neutral

Brown

Live

Page 4 of 4

9/27/2017

file://C:\Users\sh.dehghani\AppData\Local\Temp\Rar$EXa0.129\viewing\SGML_VIEW_...

3 Service Navigation

3.1 Introduction

This service manual contains technical information, which allow service personnel’s to understand and service this model.

Please place orders using the parts list and not the drawing reference numbers.

If the circuit is changed or modified, the information will be followed by service manual to be controlled with original service

manual.

3.2 About service of bundled lenses

Please refer to the following service manuals about Disassembly and Assembly or Maintenance of bundled lenses.

H-FS12060E/GK/PP: Order No.DSC1604008CE

H-ES12060PP/E/GK: Order No.DSC1702007CE

H-HSA12035PP/E/GK: Order No.DSC1703008CE

3.3 Important Notice

*When servicing, it is recommended dealing with Clean box. (Refer to “8.2. Clean Box” section of this service manual for

details.)

3.3.1 Camera Body Unit

3.3.1.1 About Flange back adjustment

* “Flange back” is the distance from the lens mount level to the Image Sensor level.

When turning the image sensor unit mounting screw even a little or removing, the “simplicity flange back adjustment” is

need.

Perform the “simplicity flange back adjustment” according to contents described in “10 Measurements and Adjustments”

section of this service manual.

3.3.1.2 About Shutter Unit (Ref. 61)

Page 1 of 11

9/27/2017

file://C:\Users\sh.dehghani\AppData\Local\Temp\Rar$EXa0.129\viewing\SGML_VIEW_...

Before exchanging the “shutter unit”, confirm that the symptom and/or phenomenon is not due to the setting of functions.

Important:

After replacing the shutter unit, the shutter unit data has to be stored to the unit.

The shutter unit supplied as service parts has affix the label of own configure data.

By inputting second line to third line of these data into the adjustment software and writing these data to Flash-ROM

(IC2003), the shutter adjustment becomes needless.

In addition, the adjustment software can read data encoded to QR Code by using WEB camera with a close-up function.

Refer to the adjustment instruction in the adjustment software for details.

3.3.1.3 About Main P.C.B. (Ref.1) & Flash-ROM (IC2003)

Before exchanging the “Main P.C.B.”, confirm that the symptom and/or phenomenon is not due to the setting of functions.

Important:

When cannot be repaired in the IC exchange, and in the case of performing the “Main P.C.B.” exchange,

carry out any of following.

In the case of exchanging the Flash-ROM (IC2003) is same way too.

1. When the camera power can be ON, and camera body and adjustment software can be communicated:

Before replacing the “Main P.C.B. and/or Flash-ROM”, proceed the EEPROM data backup from the unit.

After replacing the Main P.C.B. and/or Flash-ROM, overwrite the EEPROM data with backup data from the unit

first,

then proceed the adjustment /inspection. (Almost adjustment/inspection items can be omitted.)

Refer to the adjustment instruction in the adjustment software for details.

2. When the camera power cannot be ON, or camera body and adjustment software cannot be communicated:

Almost full adjustment/inspection must be performed after replacing the “Main P.C.B. and/or Flash-ROM”.

Refer to the adjustment instruction in the adjustment software for details.

Notes after replacement:

Make sure the camera body firmware is latest version.

3.3.1.4 About Venus Engine (IC2001) [Located on the Main P.C.B.]:

The Venus Engine (IC2001) consists of two IC chips, which are fixed together with solder.

(The so called, “Package On Package” type IC.)

NOTE:

During servicing, do not press down hard on the surface of IC2001.

3.3.2 Lens Unit (Interchangeable Lens: H-FS12060)

3.3.2.1 About Lens Main Unit (Ref. 206)

1. Lens Main Unit (Ref. 206) is not supplied due to difficulty of the transportation issue (Fragile, Dust-free packing),

and requires critical lens adjustments.

Page 2 of 11

9/27/2017

file://C:\Users\sh.dehghani\AppData\Local\Temp\Rar$EXa0.129\viewing\SGML_VIEW_...

Andere Handbücher für DC-GH5M Series

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Panasonic Kameraobjektiv Handbücher

Panasonic

Panasonic HX025 Bedienungsanleitung

Panasonic

Panasonic Lumix DMW-STC14 Bedienungsanleitung

Panasonic

Panasonic LUMIX DMW-STC20 Bedienungsanleitung

Panasonic

Panasonic S-S24 Bedienungsanleitung

Panasonic

Panasonic 12-60mm f/3.5-5.6 Bedienungsanleitung

Panasonic

Panasonic LUMIX H-X015K Bedienungsanleitung

Panasonic

Panasonic ET-ELW22C Bedienungsanleitung

Panasonic

Panasonic ET-D3LET30 Bedienungsanleitung

Panasonic

Panasonic DMW-GFC1 Bedienungsanleitung

Panasonic

Panasonic H-VSO14140 Bedienungsanleitung

Panasonic

Panasonic WV-LFY3C3 Bedienungsanleitung

Panasonic

Panasonic H-X012 Bedienungsanleitung

Panasonic

Panasonic 5025232847358 Bedienungsanleitung

Panasonic

Panasonic H-FSA45200 Bedienungsanleitung

Panasonic

Panasonic WV-LM6B2 Bedienungsanleitung

Panasonic

Panasonic H-FS1442APP Bedienungsanleitung

Panasonic

Panasonic H-PS45175PP Bedienungsanleitung

Panasonic

Panasonic WV-LFR4R5C3 Bedienungsanleitung

Panasonic

Panasonic LUMIX S PRO 70-200 mm F4 O.I.S. Bedienungsanleitung

Panasonic

Panasonic WVLZ6115 - ZOOM LENS Bedienungsanleitung

Panasonic

Panasonic Lumix G Vario H-FS45150E Bedienungsanleitung

Panasonic

Panasonic Lumix H-FSA14140 Bedienungsanleitung

Panasonic

Panasonic H-FS12032K Bedienungsanleitung

Panasonic

Panasonic H-ES12060PP Bedienungsanleitung

Beliebte Kameraobjektiv Handbücher anderer Marken

THORLABS

THORLABS ELL15 Bedienungsanleitung

FUJICA

FUJICA ZC1000 Bedienungsanleitung

Tamron

Tamron A09 Handbuch

Sony

Sony SEL-55210 Bedienungsanleitung

Sony

Sony VCL-HG2037 Bedienungsanleitung

Honeywell

Honeywell HLM25V6F12 Bedienungsanleitung

Sony

Sony VCL-ST30 Bedienungsanleitung

Canon

Canon FD 35 - 70 mm Bedienungsanleitung

Sony

Sony SAL-85F14Z - 85mm f1.4 Carl Zeiss Planar T Coated Telephoto... Bedienungsanleitung

ARRI

ARRI Lenses Bedienungsanleitung

Olympus

Olympus M.Zuiko Digital ES 300mm f4.0 IS PRO Bedienungsanleitung

Sony

Sony VCL-DE07T Bedienungsanleitung

Canon

Canon FD Lens Handbuch

Tamron

Tamron A036 Bedienungsanleitung

Samsung

Samsung 20-50mm F3.5-5.6 ED II Bedienungsanleitung

Tamron

Tamron 272E Bedienungsanleitung

Sinar

Sinar Rolleiflex 6008 AF Bedienungsanleitung

Rokinon

Rokinon SP 85mm F1.2 Bedienungsanleitung