Panasonic LUMIX H-X015E Bedienungsanleitung

SQT0244

F0414KD0

Operating Instructions

INTERCHANGEABLE LENS FOR DIGITAL CAMERA

Model No. H-X015

Please read these instructions carefully before using this product, and save this manual for future use.

until

2014/4/28

SQT0244_E.book 1 ページ２０１４年４月１１日　金曜日　午前９時１７分

SQT0244

Contents

Information for Your Safety..................................... 2

Precautions........................................................... 3

Supplied Accessories ............................................. 4

Names and Functions of Components ................... 5

Attaching/Detaching the Lens................................. 6

Cautions for Use..................................................... 9

Troubleshooting .................................................... 9

Specifications........................................................ 10

Limited Warranty (ONLY FOR AUSTRALIA)........ 11

Information for Your Safety

Keep the unit as far away as possible from

electromagnetic equipment (such as microwave

ovens, TVs, video games, radio transmitters,

high-voltage lines etc.).

≥Do not use the camera near cell phones because

doing so may result in noise adversely affecting

the pictures and sound.

≥

If the camera is adversely affected by electromagnetic

equipment and stops functioning properly, turn the

camera off and remove the battery and/or the

connected AC adaptor. Then reinsert the battery and/

or reconnect the AC adaptor and turn the camera on.

The lens can be used with a digital camera

compatible with the lens mount standard for the

“Micro Four ThirdsTM System”.

≥It cannot be mounted on the Four ThirdsTM mount

specification camera.

≥The digital camera illustrations in these operating

instructions show DMC-GM1 as an example.

≥

The appearance and specifications of products described

in this manual may differ from the actual products you

have purchased due to later enhancements.

≥

Micro Four Thirds

and Micro Four Thirds Logo

marks are trademarks or registered trademarks of

Olympus Imaging Corporation, in Japan, the United

States, the European Union and other countries.

≥Four ThirdsTM and Four Thirds Logo marks are

trademarks or registered trademarks of Olympus

Imaging Corporation, in Japan, the United States,

the European Union and other countries.

≥G MICRO SYSTEM is an interchangeable lens

type digital camera system of LUMIX based on a

Micro Four Thirds System standard.

≥LEICA is a registered trademark of Leica

Microsystems IR GmbH.

SUMMILUX

is a

registered trademark of Leica Camera AG. The

LEICA DG lenses are manufactured using

measurement instruments and quality assurance

systems that have been certified by Leica Camera

AG based on the company’s quality standards.

≥Other names of systems and products mentioned

in these instructions are usually the registered

trademarks or trademarks of the manufacturers

who developed the system or product concerned.

SQT0244_E.book 2 ページ２０１４年４月１１日　金曜日　午前９時１７分

SQT0244

-If you see this symbol-

∫Lens Care

≥Sand and dust can damage the lens. Make

sure that no sand or dust gets inside the lens

or the terminals when using the lens on a

beach, etc.

≥The lens is neither waterproof nor splash-

proof. If drops of water get onto the lens, wipe

the lens with a dry cloth.

≥Do not press the lens with excessive force.

≥When there is dirt (water, oil, and fingerprints, etc.)

on the surface of the lens, the picture may be

affected. Lightly wipe the surface of the lens with a

soft, dry cloth before and after taking pictures.

≥Do not place the lens mount facing downwards.

Do not allow the lens contact points 1to become

dirty.

Disposal of Old Equipment

Only for European Union and countries with

recycling systems

This symbol on the products,

packaging, and/or accompanying

documents means that used

electrical and electronic products

must not be mixed with general

household waste.

For proper treatment, recovery

and recycling of old products,

please take them to applicable

collection points in accordance

with your national legislation.

By disposing of them correctly,

you will help to save valuable resources and prevent

any potential negative effects on human health and

the environment.

For more information about collection and recycling,

please contact your local municipality.

Penalties may be applicable for incorrect disposal of

this waste, in accordance with national legislation.

Precautions

ENGLISH

SQT0244_E.book 3 ページ２０１４年４月１１日　金曜日　午前９時１７分

SQT0244

∫About Condensation (Fogging of the

Lens)

≥Condensation occurs when there are differences

in temperature and humidity as described below.

Condensation can cause the lens to become dirty

and lead to mold and malfunctioning, so exercise

caution in the following situations:

– When the camera is brought indoors from outside

during cold weather

– When the camera is brought into an air-

conditioned car

– When cold air from an air conditioner is directly

blown onto the lens

– In humid places

≥Put the camera into a plastic bag to allow it to

acclimatize to the surrounding temperature in

order to prevent condensation. If condensation

occurs, turn the power off and leave it for about

two hours. Once the camera acclimatizes to the

surrounding temperature the condensation will go

away naturally.

Supplied Accessories

[Inspection to be performed when you unpack

the unit]

When removing the unit from its packing box, check

that the main unit and the supplied accessories are

there and also check their external appearance and

functions to verify that they have not sustained any

damage during distribution and transportation.

If you discover any trouble, contact your vendor

before using the product.

Product numbers correct as of April 2014. These

may be subject to change.

VFC4456

:SFC0191

:SFC0190

:SFC0090

:SFC0089

:SFC0133

:SFC0093

SYF0001

VFC4605

SQT0244_E.book 4 ページ２０１４年４月１１日　金曜日　午前９時１７分

SQT0244

≥The lens cap, lens rear cap, and decoration ring

are attached to the lens at the time of purchase. In

addition, the lens hood cap is attached to the lens

hood.

Names and Functions of

Components

1Lens surface

2Decoration ring

Remove this cover when using the lens hood.

3Aperture ring

Rotate this to adjust the aperture value.

≥If you set the camera to Aperture-Priority AE

Mode or Manual Exposure Mode, the aperture

value of the ring will be enabled.

≥If you set the position of the aperture ring to [A],

the aperture value of the camera will be enabled.

≥When the aperture ring is enabled, check if the

aperture value has changed after attaching or

removing the decoration ring.

1Lens Pouch 4Lens Cap

2Lens Hood

A: Black

B: Silver

5Lens Rear Cap

3Lens Hood Cap

A: Black

B: Silver

6Decoration ring

A: Black

B: Silver

1234 5 6 7

SQT0244_E.book 5 ページ２０１４年４月１１日　金曜日　午前９時１７分

SQT0244

4Focus ring

Rotate to focus when taking pictures with manual

focus (MF).

5[AF/MF] switch

This allows you to switch between Auto Focus (AF)

and Manual Focus (MF). If you set [MF], you can

use the focus ring to adjust the focus.

≥When either the [AF/MF] switch of the lens or the

setting of the camera is set to [MF], Manual Focus

(MF) is enabled.

6Lens fitting mark

7Contact points

Note

≥When using this lens and the flash to record a

subject very close to the camera, it is possible that

a darker shadowed area may appear in the lower

portion of the picture. This situation is not a

malfunction and is caused when the flash is

partially blocked by the lens. This situation may be

worsened when the lens hood is used.

≥

In very quiet situations Auto Focus operating sounds

may be recorded during motion picture recording.

This is not a malfunction. In such situations,

switching to Manual Focus will improve the situation.

≥The aperture can be adjusted with the aperture

ring only when a Panasonic digital camera is

attached to the lens. (As of April 2014)

Attaching/Detaching the Lens

Check that the camera is

turned off.

≥Remove the lens rear cap

from the lens.

∫Attaching the Lens

Align the lens fitting

marks A on the

camera body and the

lens and then rotate

the lens in the

direction of the

arrow until it clicks.

• Do not press the lens release button B when

you attach a lens.

• Do not try to attach the lens when holding it at an

angle to the camera body as the lens mount may

get scratched.

• Check that the lens is attached correctly.

• Be sure to remove the lens cap when recording.

SQT0244_E.book 6 ページ２０１４年４月１１日　金曜日　午前９時１７分

SQT0244

∫Detaching the Lens

While pressing on the

lens release button B,

rotate the lens toward

the arrow until it stops

and then remove.

• Attach the lens rear cap so

that the lens contact point does not get scratched.

• Attach the body cap to the camera so no dirt or

dust will get inside the main unit.

∫

Attaching the Lens Hood (Supplied Accessory)

≥Before attaching the lens

hood, make sure to

remove the lens cap. The

lens hood cannot be

attached unless you

remove the lens cap.

1 Rotate the decoration ring Cin the

direction of the arrow to remove it.

2 Align the mounting index Don the lens

hood with the mark on the tip of the lens.

3 Rotate the lens hood in the direction of

the arrow until it clicks into place, and

align the stop position Eon the lens

hood with the index on the tip of the lens.

Note

≥

When using this lens and the flash to record a subject

very close to the camera, it is possible that a darker

shadowed area may appear in the lower portion of the

picture. This situation is not a malfunction and is caused

when the flash is partially blocked by the lens. This

situation may be worsened when the lens hood is used.

≥When using the AF assist lamp in the dark, detach

the lens hood.

≥Make sure to remove the lens hood cap when

recording an image.

SQT0244_E.book 7 ページ２０１４年４月１１日　金曜日　午前９時１７分

SQT0244

∫Attaching the decoration ring

≥Before attaching the decoration ring, make

sure to remove the lens cap.

1 Align the mounting position G on the

decoration ring with a position

approximately 90xaway from the lens

fitting mark F to fit the decoration ring

into place.

2 Rotate the decoration ring in the

direction of the arrow to align the

mounting position Gon the decoration

ring with the lens fitting mark F.

∫Attaching Filters

≥Vignetting may occur if using 2 or more

MC protectors (optional: DMW-LMC46), PL filters

(optional: DMW-LPL46) or ND filters (optional:

DMW-LND46), or if using thick protectors and/or

filters.

≥The filter may become impossible to remove if

excessively tightened, so please refrain from

tightening it too strongly.

≥It is possible to attach the lens cap with the filter

already attached.

≥When the lens hood is attached to this lens, you

cannot attach a filter to it.

≥You cannot attach a conversion lens or adaptor to

this lens. A filter may be used, but attaching any

other element may cause damage to the lens.

SQT0244_E.book 8 ページ２０１４年４月１１日　金曜日　午前９時１７分

SQT0244

Cautions for Use

Take care not to drop or knock the lens. Also

take care not to put a lot of pressure on the lens.

≥

Take care not to drop the bag that you inserted the

lens in as it may strongly shock the lens. The camera

may stop operating normally and pictures may no

longer be recorded. Also, the lens may be damaged.

≥

When carrying the digital camera with the lens

attached, hold both the digital camera and the lens.

When using pesticides and other volatile

substances around the camera make sure that

they do not get onto the lens.

≥

If such substances get onto the lens they can

damage the exterior case or cause the paint to peel.

Do not point the lens at the sun or other strong

light sources.

≥This could cause the lens to collect an excessive

amount of light, resulting in fire and malfunction.

≥

Under no circumstances should the unit be stored in

any of the following locations since doing so may

cause problems in operation or malfunctioning.

– In direct sunlight or on a beach in summer

– In locations with high temperatures and humidity levels or

where the changes in temperature and humidity are acute

– In locations with high concentrations of sand, dust or dirt

– Where there is fire

– Near heaters, air conditioners or humidifiers

– Where water may make the unit wet

– Where there is vibration

– Inside a vehicle

≥

Refer also to the operating instructions of the digital camera.

≥

When the unit is not going to be used for a prolonged

period, we recommend storing with a desiccant (silica

gel). Failure to do so may result in performance

failure caused by mold, etc. It is recommended that

you check the unit’s operation prior to use.

≥

Do not leave the lens in contact with rubber or plastic

products for extended periods of time.

≥

Do not touch the lens contact point. Doing so can

cause failure of the unit.

≥

Do not disassemble or alter the unit.

Do not use benzine, thinner, alcohol or other

similar cleaning agents to clean the lens glass or

exterior cabinet.

≥Using solvents can damage the lens or cause the

paint to peel.

≥

Wipe off any dust or fingerprints with a soft, dry cloth.

≥Use a dry, dust cloth to remove dirt and dust on

the focus ring and the aperture ring.

≥Do not use a household detergent or a chemically

treated cloth.

When I turn on or off the camera or when I shake the

lens, I hear a sound, for example a rattling sound.

When I take pictures of a bright subject, such as a

subject outside, or when I take pictures with a large

aperture value, the lens makes a sound.

≥This is the sound of lens or aperture movement

and is not a malfunction.

Troubleshooting

SQT0244_E.book 9 ページ２０１４年４月１１日　金曜日　午前９時１７分

SQT0244

Specifications

Specifications are subject to change without notice.

INTERCHANGEABLE LENS FOR DIGITAL CAMERA

“LEICA DG SUMMILUX 15 mm/F1.7 ASPH.”

Focal length f=15 mm

(35 mm film camera equivalent: 30 mm)

Aperture type 7 diaphragm blades/circular aperture diaphragm

Maximum aperture F1.7

Minimum aperture value F16

Lens construction 9 elements in 7 groups (3 aspherical lenses)

Nano surface coating Yes

In focus distance 0.2 m to ¶ [from the focus distance reference line]

Maximum image magnification 0.1k(35 mm film camera equivalent: 0.2k)

Optical image stabiliser Not available

[AF/MF] switch Available (Switching AF/MF)

Mount “Micro Four Thirds Mount”

Angle of view 72x

Filter diameter 46 mm

Max. diameter Approx. 57.5 mm

Overall length Approx. 36 mm

(from the tip of the lens to the base side of the lens mount)

Mass Approx. 115 g

SQT0244_E.book 10 ページ２０１４年４月１１日　金曜日　午前９時１７分

Inhaltsverzeichnis

Sprachen:

Andere Panasonic Kameraobjektiv Handbücher

Panasonic

Panasonic LUMIX G X Vario 45-175mm f/4.0-5.6 Bedienungsanleitung

Panasonic

Panasonic LUMIX S Pro R70200 Bedienungsanleitung

Panasonic

Panasonic H-FS35100PP Bedienungsanleitung

Panasonic

Panasonic LUMIX H-HSA12035 Bedienungsanleitung

Panasonic

Panasonic H-HS030 Bedienungsanleitung

Panasonic

Panasonic H-PS45175 Bedienungsanleitung

Panasonic

Panasonic Lumix H-X015 Bedienungsanleitung

Panasonic

Panasonic Lumix H-HS35100 Bedienungsanleitung

Panasonic

Panasonic S-S24 Bedienungsanleitung

Panasonic

Panasonic H-FS045200 - Lumix Telephoto Zoom Lens Bedienungsanleitung

Panasonic

Panasonic LUMIX S-X50GC Bedienungsanleitung

Panasonic

Panasonic WV-LP6 Bedienungsanleitung

Panasonic

Panasonic ET-D75LE30 Bedienungsanleitung

Panasonic

Panasonic H-VSO14140 Bedienungsanleitung

Panasonic

Panasonic H-HS043 Bedienungsanleitung

Panasonic

Panasonic WV-LZ61 Bedienungsanleitung

Panasonic

Panasonic Lumix G Vario H-FS45150E Bedienungsanleitung

Panasonic

Panasonic Lumix H-H020 Bedienungsanleitung

Panasonic

Panasonic WVLZ6115 - ZOOM LENS Bedienungsanleitung

Panasonic

Panasonic ET-DLE085 Bedienungsanleitung

Panasonic

Panasonic WV-LA12A Bedienungsanleitung

Panasonic

Panasonic ET-EMW200 Bedienungsanleitung

Panasonic

Panasonic WV-LA36 Bedienungsanleitung

Panasonic

Panasonic H-FS35100PP Bedienungsanleitung

Beliebte Kameraobjektiv Handbücher anderer Marken

THORLABS

THORLABS ELL15 Bedienungsanleitung

FUJICA

FUJICA ZC1000 Bedienungsanleitung

Tamron

Tamron A09 Handbuch

Sony

Sony SEL-55210 Bedienungsanleitung

Sony

Sony VCL-HG2037 Bedienungsanleitung

Honeywell

Honeywell HLM25V6F12 Bedienungsanleitung

Sony

Sony VCL-ST30 Bedienungsanleitung

Canon

Canon FD 35 - 70 mm Bedienungsanleitung

Sony

Sony SAL-85F14Z - 85mm f1.4 Carl Zeiss Planar T Coated Telephoto... Bedienungsanleitung

ARRI

ARRI Lenses Bedienungsanleitung

Olympus

Olympus M.Zuiko Digital ES 300mm f4.0 IS PRO Bedienungsanleitung

Sony

Sony VCL-DE07T Bedienungsanleitung

Canon

Canon FD Lens Handbuch

Tamron

Tamron A036 Bedienungsanleitung

Samsung

Samsung 20-50mm F3.5-5.6 ED II Bedienungsanleitung

Tamron

Tamron 272E Bedienungsanleitung

Sinar

Sinar Rolleiflex 6008 AF Bedienungsanleitung

Rokinon

Rokinon SP 85mm F1.2 Bedienungsanleitung