Panasonic LUMIX S Pro R70200 Bedienungsanleitung

18 DVQX1725

Operating Instructions

INTERCHANGEABLE LENS

FOR DIGITAL CAMERA

Thank you for purchasing Panasonic product.

Please read these instructions carefully before using this

product, and save this manual for future use.

This lens can be attached to a 35 mm digital camera that

complies with the Leica Camera AG L-Mount standard

and that is equipped with a full-frame image sensor.

0L-Mount is a trademark or registered trademark of

Leica Camera AG.

0Other names, company names, product names

mentioned in this document are trademarks or

registered trademarks of the companies concerned.

Information for Your Safety .................................... 19

Precautions ............................................................ 20

Supplied Accessories............................................. 21

Names and Functions of Components................... 22

Attaching the Lens ................................................. 23

Switching AF/MF.................................................... 24

Using the Tripod Mount..........................................24

Cautions for Use .................................................... 26

Troubleshooting ..................................................... 26

Specifications......................................................... 27

Limited Warranty (ONLY FOR U.S.A.)................... 28

Limited Warranty (ONLY FOR CANADA) .............. 30

Contents

S-R70200-DVQX1725ZA.book 18 ページ２０１９年１月２９日　火曜日　午後６時５５分

DVQX1725

English

Information for Your Safety

Keep the unit as far away as possible from electromagnetic

equipment (such as microwave ovens, TVs, video games,

radio transmitters, high-voltage lines etc.).

Do not use the camera near cell phones because doing so may

result in noise adversely affecting the pictures and sound.

0If the camera is adversely affected by electromagnetic

equipment and stops functioning properly, turn the

camera off and remove the battery and/or the

connected AC adaptor. Then reinsert the battery and/or

reconnect the AC adaptor and turn the camera on.

THE FOLLOWING APPLIES ONLY IN THE U.S.A.

FCC Note:

This equipment has been tested and found to comply

with the limits for a Class B digital device, pursuant to

Part 15 of the FCC Rules. These limits are designed to

provide reasonable protection against harmful

interference in a residential installation. This equipment

generates, uses, and can radiate radio frequency energy

and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio

communications. However, there is no guarantee that

interference will not occur in a particular installation. If

this equipment does cause harmful interference to radio

or television reception, which can be determined by

turning the equipment off and on, the user is encouraged

to try to correct the interference by one or more of the

following measures:

0Reorient or relocate the receiving antenna.

0Increase the separation between the equipment and

receiver.

0Connect the equipment into an outlet on a circuit

different from that to which the receiver is connected.

0Consult the dealer or an experienced radio/TV

technician for help.

Any unauthorized changes or modifications to this equipment

would void the user’s authority to operate this device.

This device complies with Part 15 of the FCC Rules.

Operation is subject to the following two conditions: (1)

This device may not cause harmful interference, and (2)

this device must accept any interference received,

including interference that may cause undesired operation.

Supplier’s Declaration of Conformity

Trade Name: Panasonic

Model No.: S-R70200

Responsible Party:

Panasonic Corporation of North America

Two Riverfront Plaza, Newark, NJ

07102-5490

Support Contact: http://shop.panasonic.com/support

THE FOLLOWING APPLIES ONLY IN CANADA.

CAN ICES-3(B)/NMB-3(B)

S-R70200-DVQX1725ZA.book 19 ページ２０１９年１月２９日　火曜日　午後６時５５分

20 DVQX1725

-If you see this symbol-

Precautions

∫Lens care

0Do not subject to strong vibration, shock, or

pressure. These may cause malfunction or

damage.

– Don’t press hard on the lens.

Take care not to drop or bump the lens when carrying it.

– When carrying the digital camera with the lens

attached, hold both the lens and the digital camera to

carry them.

– Take care not to drop or bump the bag in which you have put

the lens.

When there is dirt (water, oil, and fingerprints, etc.) on the

surface of the lens, the images may be affected. Lightly wipe

the surface of the lens with a soft, dry cloth before and after

recording.

0When the lens is not in use, be sure to attach the lens

cap and lens rear cap to prevent dust and other

particles from accumulating on or entering the lens.

0To protect the lens contact

points (A), do not do the

following. These may

cause malfunction.

– Touch the lens contact

points.

– Allow the lens contact

points to become dirty.

– Place the lens with its

mount surface facing

down.

∫Dust and splash resistant

0The dust and splash resistant of the camera will

not prevent the entry of dust or water droplets

completely. Take the following precautions to

provide satisfactory dust and splash resistant

performance. If the lens is not working properly,

consult the dealer or your nearest Service Center.

Disposal of Old Equipment

Only for European Union and countries with recycling

systems

This symbol on the products, packaging,

and/or accompanying documents means

that used electrical and electronic products

must not be mixed with general household

waste.

For proper treatment, recovery and recycling

of old products, please take them to

applicable collection points in accordance with your

national legislation.

By disposing of them correctly, you will help to save

valuable resources and prevent any potential negative

effects on human health and the environment.

For more information about collection and recycling,

please contact your local authority.

Penalties may be applicable for incorrect disposal of

this waste, in accordance with national legislation.

S-R70200-DVQX1725ZA.book 20 ページ２０１９年１月２９日　火曜日　午後６時５５分

DVQX1725

English

– Attach to attach a digital camera that is dust and

splash resistant.

– When attaching or removing the lens, be careful so

that foreign objects such as sand, dust, and water

droplets do not adhere to or enter the lens mount

rubber, contact points, digital camera and lens.

– If the lens is exposed to water droplets or other

liquids, wipe them off with a soft, dry cloth.

0To improve the dust and splash resistant performance

of the lens, a lens mount rubber is used in the mount.

– The lens mount rubber will leave scuff marks on the

digital camera mount, but this does not impact

performance.

– For information on changing the lens mount rubber,

contact your nearest Service Center.

∫Condensation (when the lens is fogged up)

0Condensation occurs when the ambient temperature or

humidity changes. Please be careful, as it may cause

lens stains, mold and malfunction.

0If condensation occurs, turn off the digital camera and

leave it for approx. 2 hours. The fog will disappear

naturally when the temperature of the digital camera

becomes close to the ambient temperature.

0The appearance and specifications of products

described in this document may differ from the actual

products you have purchased due to later

enhancements.

Supplied Accessories

Product numbers correct as of January 2019. These may

be subject to change.

¢Fitted to the lens at the time of purchase.

1 Lens pouch

2 Lens hood

3 Lens cap¢

4 Lens rear cap¢

5 Tripod mount¢

SFC0360 DVZE1035Z

2134

1GE1Z276Z

DVYE1130Z

RGE1Z276Z

S-R70200-DVQX1725ZA.book 21 ページ２０１９年１月２９日　火曜日　午後６時５５分

22 DVQX1725

Names and Functions of

Components

1Lens surface

2Focus ring

Switches between AF (auto focus) and MF (manual

focus) by sliding the focus ring forwards or

backwards. (l 24)

Rotates the focus ring to focus when set to MF.

3Zoom ring

Zooms to telephoto or wide-angle.

4Tripod mount (l 24)

5Tripod mount locking knob

6O.I.S. switch

The stabilizer function is set to activate if the O.I.S.

switch is set to [ON].

0We recommend setting the O.I.S. switch to [OFF]

when using a tripod.

7Contact points

8Lens fitting mark

9Lens mount rubber

Note

0There may be differences in focus when you use zoom

after focusing. Focus again.

0If the sound of AF operation and stabilizer operation

bothers you during video recording, it is recommended

to record as follows:

– Slide the focus ring to the MF side to record.

– Set the O.I.S. switch to [OFF] and use a tripod to

record.

23456

S-R70200-DVQX1725ZA.book 22 ページ２０１９年１月２９日　火曜日　午後６時５５分

DVQX1725

English

Attaching the Lens

For information on how to attach the lens, refer to the

operating instructions for your digital camera.

0Attach the lens after turning off the digital camera.

0Attach the lens after removing

the lens rear cap.

After removing the lens from the

digital camera, be sure to attach

the lens cap and lens rear cap to

prevent dust and other particles

from accumulating on or entering

the lens.

∫Attaching the lens hood

1Align mark A ( ) on

the lens hood with the

mark on the tip of the

lens.

2Rotate the lens hood in

the direction of the

arrow to align mark B

( ) on the lens hood

with the mark on the tip

of the lens.

0Attach the lens hood by

rotating it until it clicks.

∫Removing the lens hood

While pressing the lens

hood button, rotate the

lens hood in the direction

of the arrow and then

remove it.

Note

0When carrying, the lens hood can be attached in the

reverse direction.

1Remove the lens hood.

2Align mark C ( ) on the lens hood with the mark

on the tip of the lens.

3Attach the lens hood by rotating it in the direction of

the arrow until it clicks.

0It is recommended to remove the lens hood during

flash photography as the lens hood can block the light

from the flash.

0To prevent dropping of the lens, you should never carry

the lens by just holding the lens hood.















S-R70200-DVQX1725ZA.book 23 ページ２０１９年１月２９日　火曜日　午後６時５５分

24 DVQX1725

∫Notes on filter use

0It is possible to attach the lens cap or the lens hood

with the filter already attached.

0If you use two or more filters at the same time, part of a

recorded image may darken.

0It is not possible to attach any items other than filters

such as a conversion lens or adaptor to the front of the

lens and use it in combination with this lens.

Lens damage may result if such items are attached.

Switching AF/MF

Switch AF/MF by sliding the

focus ring

forwards or

backwards (focus clutch

mechanism).

0When the digital camera is

set to MF, the operation will

be MF irrespective of the

position of the focus ring.

Check the length indication

when using MF. Use it as a guide

for focusing.

You can set the amount that

the focus moves with the focus

ring using menu settings in

compatible digital cameras.

Switch the lens to AF and set

the digital camera to MF. Refer to the operating

instructions for the digital camera for details.

Using the Tripod Mount

When using a tripod, attach it

to the tripod mount of the

lens.

0When a tripod is attached to

the tripod mount of the

digital camera, damage to

the lens may result when

carrying.

∫Changing the vertical/horizontal orientation

This way, you can quickly switch between the vertical

and horizontal orientation of the digital camera while the

tripod is in use.

1Rotate the tripod mount

locking knob in the

direction indicated by the

arrow to loosen.

AF MF



3.1

0.92 1.2 1.5 2.2 4 10 ĩm

45 7 1328 ft



S-R70200-DVQX1725ZA.book 24 ページ２０１９年１月２９日　火曜日　午後６時５５分

DVQX1725

English

2Rotate the digital

camera and lens to

change the position.

3Rotate the tripod

mount locking knob in the

direction indicated by the

arrow to tighten firmly.

∫Detaching the tripod mount

1Rotate the tripod

mount locking knob in

the direction indicated

by the arrow to loosen.

2Match the marks on the

tripod mount and the

tripod mount locking

knob.

3While pulling out the

tripod mount locking

knob, open and remove

the tripod mount.

0When detaching the

tripod mount, support the

lens and digital camera

to ensure they do not fall.

∫Attaching the tripod mount

Attach by reversing the steps used to detach.

0Match the marks on the

tripod mount and the

lens.

0When attaching the

tripod mount, pull out the

tripod mount locking

knob first and then close

the tripod mount.

0Be careful not to pinch

your fingers between the

tripod mount and the lens.

S-R70200-DVQX1725ZA.book 25 ページ２０１９年１月２９日　火曜日　午後６時５５分

26 DVQX1725

Cautions for Use

0Do not spray the lens with insecticides or volatile

chemicals.

– If such substances get onto the lens they can

damage the exterior case or cause the paint to peel.

0Do not point the lens at the sun or other strong

light sources.

– This may cause the lens to collect an excessive

amount of light, resulting in fire and malfunction.

0Do not use while directly touching the lens at low

temperatures for a long period of time.

– In cold places (environments below 0 oC (32 oF), such

as ski slopes), prolonged direct contact with the metal

parts of the lens may cause skin injury. Use gloves or

similar when using the lens for long periods.

0Use a soft, dry, dust-free cloth to clean the lens.

– Do not use benzine, thinner, alcohol or other similar

cleaning agents to clean the lens. Using solvents

may damage the lens or cause the paint to peel.

– Do not use a household detergent or a chemically

treated cloth.

0Do not keep products made of rubber, PVC or similar

materials in contact with the lens for a long period of

time.

0Do not disassemble or alter this product.

0When the lens is not going to be used for a prolonged

period, we recommend storing with a desiccant (silica

gel).

0Check all the parts before recording when you have not

used the lens for a long period of time.

0Avoid using or storing the lens in any of the following

locations as this may cause problems in operation or

malfunctioning:

– In direct sunlight or on a beach in summer

– In locations with high temperatures and humidity

levels or severe changes in temperature and

humidity

– In sandy or dusty locations

– Where there is fire

– Near heaters, air conditioners or humidifiers

– Where water may make the lens wet

– Where there is vibration

– Inside a vehicle

0Refer also to the operating instructions for the digital

camera.

Troubleshooting

A rattling sound, etc. is heard when the digital

camera is turned on or off or the lens is shaken.

There is a sound from the lens when taking pictures.

0This is the sound of the lens moving and aperture

operation. It is not a malfunction.

S-R70200-DVQX1725ZA.book 26 ページ２０１９年１月２９日　火曜日　午後６時５５分

DVQX1725

English

Specifications

The specifications are subject to change for performance enhancement.

INTERCHANGEABLE LENS FOR DIGITAL CAMERA “LUMIX S PRO 70-200 mm F4 O.I.S.”

Mount Leica Camera AG L-Mount

Focal length f=70 mm to 200 mm

Lens construction 23 elements in 17 groups (1 aspherical lens, 1 UED lens, 3 ED lenses, 1 UHR lens)

Aperture type 9 diaphragm blades/Circular aperture diaphragm

Maximum aperture F4.0

Minimum aperture value F22

Angle of view 34x (Wide) to 12o (Tele)

Recording range 0.92 m (3.02 feet) to ¶ (from the focus distance reference line)

Maximum image

magnification 0.25k

Image stabilizer Yes

Filter diameter 77 mm

Maximum diameter ‰84.4 mm (3.3q)

Overall length

Approx. 179 mm (7.0

) (from the tip of the lens to the base side of the lens mount)

Mass (Weight) Approx. 985 g (2.17 lb) (excluding the external tripod mount)

Dust and splash resistant Yes

Recommended operating

temperature j10 oC to 40 oC (14 oF to 104 oF)

Permissible relative

humidity 10%RH to 80%RH

S-R70200-DVQX1725ZA.book 27 ページ２０１９年１月２９日　火曜日　午後６時５５分

Inhaltsverzeichnis

Andere Panasonic Kameraobjektiv Handbücher

Panasonic

Panasonic Lumix H-FSA14140 Bedienungsanleitung

Panasonic

Panasonic Lumix H-XA025 Bedienungsanleitung

Panasonic

Panasonic Lumix H-X1025 Bedienungsanleitung

Panasonic

Panasonic H-HS030PP Bedienungsanleitung

Panasonic

Panasonic Lumix H-VS014140 Bedienungsanleitung

Panasonic

Panasonic Lumix H-FS014045 Bedienungsanleitung

Panasonic

Panasonic H-HS043 Bedienungsanleitung

Panasonic

Panasonic Lumix S-R70300 Installationsanleitung

Panasonic

Panasonic ET-D75LE30 Bedienungsanleitung

Panasonic

Panasonic H-FSA45200 Bedienungsanleitung

Panasonic

Panasonic S-S50 Installationsanleitung

Panasonic

Panasonic WV-LM6B2 Bedienungsanleitung

Panasonic

Panasonic H-FS12032K Bedienungsanleitung

Panasonic

Panasonic Lumix H-ES12060 Bedienungsanleitung

Panasonic

Panasonic H-FS045200 - Lumix Telephoto Zoom Lens Bedienungsanleitung

Panasonic

Panasonic 33335 Bedienungsanleitung

Panasonic

Panasonic 5025232898695 Bedienungsanleitung

Panasonic

Panasonic ET-DLE085 Bedienungsanleitung

Panasonic

Panasonic WV-LFY3C3 Bedienungsanleitung

Panasonic

Panasonic ET-D3LET30 Bedienungsanleitung

Panasonic

Panasonic Lumix H-X015E-K Bedienungsanleitung

Panasonic

Panasonic H-FS12060 Bedienungsanleitung

Panasonic

Panasonic WV-LZ61 Bedienungsanleitung

Panasonic

Panasonic H-RS100400 Bedienungsanleitung

Beliebte Kameraobjektiv Handbücher anderer Marken

THORLABS

THORLABS ELL15 Bedienungsanleitung

FUJICA

FUJICA ZC1000 Bedienungsanleitung

Tamron

Tamron A09 Handbuch

Sony

Sony SEL-55210 Bedienungsanleitung

Sony

Sony VCL-HG2037 Bedienungsanleitung

Honeywell

Honeywell HLM25V6F12 Bedienungsanleitung

Sony

Sony VCL-ST30 Bedienungsanleitung

Canon

Canon FD 35 - 70 mm Bedienungsanleitung

Sony

Sony SAL-85F14Z - 85mm f1.4 Carl Zeiss Planar T Coated Telephoto... Bedienungsanleitung

ARRI

ARRI Lenses Bedienungsanleitung

Olympus

Olympus M.Zuiko Digital ES 300mm f4.0 IS PRO Bedienungsanleitung

Sony

Sony VCL-DE07T Bedienungsanleitung

Canon

Canon FD Lens Handbuch

Tamron

Tamron A036 Bedienungsanleitung

Samsung

Samsung 20-50mm F3.5-5.6 ED II Bedienungsanleitung

Tamron

Tamron 272E Bedienungsanleitung

Sinar

Sinar Rolleiflex 6008 AF Bedienungsanleitung

Rokinon

Rokinon SP 85mm F1.2 Bedienungsanleitung