Panasonic ET-MDN12G10C Bedienungsanleitung

Thank you for purchasing this Panasonic product.

■Before using this product, please read these “Operating Instructions” and

the “Operating Instructions” of the projector carefully and save the manuals

for future use.

■Before using this product, be sure to read “Read this rst!” (xpage 3).

DPQX1185ZC

Printed in China

Interface Board for 12G-SDI Commercial Use

Operating Instructions

ENGLISH

Model No. ET-MDN12G10C

2 - ENGLISH

Contents

Read this rst! 3

Precautions for use 5

Supported projector 5

About the handling of the product 5

Disposal 5

Accessories 5

Part names and functions 6

Installing the Interface Board 7

Before installing or removing the Interface Board 7

How to install the Interface Board 8

How to remove the Interface Board 9

Specications 10

ENGLISH - 3

Read this rst!

WARNING:

Do not spill water on this product or allow this product to get wet.

Doing so may cause re, electric shock, or malfunction due to short circuit

or overheating.

fDo not place a container with liquid close to this product.

fConsult your dealer when liquid such as water is spilled on this

product.

Do not place the supplied screws in a location that a child can reach.

Accidentally swallowing them can cause a physical harm.

fSeek a medical advice immediately if a child might have swallowed a

screw.

Do not disassemble or modify.

Doing so may cause electric shock or re. It may also cause a malfunction.

CAUTION:

Do not place this product in a location with excessive humidity or

dust, or in a location exposed to oil smoke or steam.

Doing so may cause re or electric shock.

Do not place this product in extremely hot location.

Doing so may deteriorate the part, or may cause re.

fDo not install or store in a location with direct sunlight or close to the

heating device, etc.

Turn o󰀨 the power and disconnect the power plug from the outlet

when installing or removing this product to/from the projector.

Failure to do so may cause electric shock.

4 - ENGLISH

Read this rst!

Name and quantity of hazardous substances contained in the

product

Parts Hazardous substances

Pb Hg Cd Cr VI PBB PBDE

Printed circuit boards

(PCB)

Accessories

This table is prepared in accordance with the provisions of SJ/T 11364.

: The amount of hazardous substances included in all homogeneous

materials for the relevant part does not exceed the limit specied in GB/T

26572.

: The amount of hazardous substances included in all homogeneous

materials for the relevant part exceeds the limit specied in GB/T 26572.

Precautions for use

ENGLISH - 5

Precautions for use

This product is a 12G-SDI signal compatible interface board for use installed

in a Panasonic projector.

Supported projector

PT-SRQ32KC, PT-SRQ13KC, PT-SRQ22KC

(As of March 2019)

Note

fProducts other than the above may also be supported. Check the Operating Instructions of

your projector.

fIf the main version of the rmware of the PT-SRQ32KC, PT-SRQ13KC is less than 3.00, this

interface board cannot be used. For details, contact your dealer.

About the handling of the product

rDo not touch the connector section of the Interface Board

directly with your hands.

The component may be damaged by the static electricity. Handle this

product after removing the static in your body by touching the surrounding

metal, etc.

Disposal

To dispose of the product, ask your local authorities or dealer for correct

methods of disposal.

Accessories

Make sure that the following accessories are provided with your product.

Numbers enclosed in < > show the number of accessories.

Screw <4>

(XSB3+8FN)

Attention

fAppropriately discard the packaging material after unpacking the product.

fFor missing accessories, consult your dealer.

fStore small parts in an appropriate manner, and keep them away from small children.

Precautions for use

6 - ENGLISH

Note

fThe supplied screws are spare. Use them when a screw to x the slot cover of the projector

is lost.

fThe model numbers of accessories are subject to change without prior notice.

Part names and functions

5 21 43 5

1 <SDI 1 输入> terminal

This is a terminal to input SDI signals

(SD-SDI / HD-SDI / 3G-SDI / 6G-SDI /

12G-SDI).

2 <SDI 2 输入/1 输出> terminal

This is a terminal to input SDI signals

(SD-SDI / HD-SDI / 3G-SDI). It is also

an active through terminal to output the

SDI signals (SD-SDI / HD-SDI / 3G-SDI

/ 6G-SDI / 12G-SDI) input to the <SDI 1

输入> terminal.

3 <SDI 3 输入> terminal

This is a terminal to input SDI signals

(SD-SDI / HD-SDI / 3G-SDI / 6G-SDI /

12G-SDI).

4 <SDI 4 输入/3 输出> terminal

This is a terminal to input SDI signals

(SD-SDI / HD-SDI / 3G-SDI). It is also

an active through terminal to output the

SDI signals (SD-SDI / HD-SDI / 3G-SDI

/ 6G-SDI / 12G-SDI) input to the <SDI 3

输入> terminal.

5 Handle

Note

fThe <SDI 2 输入/1 输出> terminal and <SDI 4 输入/3 输出> terminal do not support the input

of 6G-SDI signals and 12G-SDI signals.

fTo use the <SDI 2 输入/1 输出> terminal and <SDI 4 输入/3 输出> terminal as output

terminals, you need to change the settings of the projector. Check the Operating Instructions

of your projector.

Installing the Interface Board

ENGLISH - 7

Installing the Interface Board

It is recommended to ask a qualied technician to install or remove the

Interface Board to a projector. A malfunction may occur due to static

electricity. Consult your dealer.

Before installing or removing the Interface Board

fAlways turn o󰀨 the power of the projector before installing or removing the

Interface Board.

gMake sure to follow the procedure described in the Operating

Instructions of your projector when turning o󰀨 the power.

fDo not touch the connector section of the Interface Board directly with your

hands.

gThe component may be damaged by the static electricity.

fRemove the static charge from your body by touching the surrounding

metal, etc., in advance to prevent the static electricity damage.

fTake care not to get injured when installing or removing the Interface

Board.

gHands may be injured by the opening of the blank slot of the projector or

the edge of the bracket of the Interface Board.

fWhen installing the Interface Board to the slot, insert it into the connector

straight and slowly.

gIt may not operate or cause malfunction if it is not correctly installed.

fInstall and use this interface board in one of the <SLOT 1> and <SLOT 2>

slots. If this interface board is installed both in <SLOT 1> and in <SLOT

2>, only the one installed in <SLOT 1> can be used.

Installing the Interface Board

8 - ENGLISH

How to install the Interface Board

Screws (4 locations) Screws (4 locations)

Salient

Guide groove

Slot cover

Fig. 1 Fig. 2 Fig. 3

1) Remove the slot cover. (Fig. 1)

fRemove the four screws xing the slot cover of the projector by

rotating counterclockwise with a Phillips screwdriver. The removed

screws are used to x the Interface Board.

fWhen removing the fourth screw, hold the slot cover with your hand so

it will not fall.

fTo replace from other Interface Board, remove the Interface Board

following the procedure in “How to remove the Interface Board”

(xpage 9).

2) Install the Interface Board to the projector. (Fig. 2)

fInsert the guide groove of the Interface Board aligned to the salient of

the slot. Insert the bracket rmly all the way in.

3) Fix the Interface Board. (Fig. 3)

fTighten and x with the four screws removed in Step 1).

Attention

fThe removed slot cover is required when the unnecessary Interface Board is removed. Store

it so it can be attached in the future.

Installing the Interface Board

ENGLISH - 9

How to remove the Interface Board

Handle

Fig. 1

1) Remove the Interface Board. (Fig. 1)

fRemove the four screws xing the Interface Board by rotating

counterclockwise with a Phillips screwdriver. The removed screws are

used to x the slot cover.

fHold the handle of the Interface Board and remove it slowly.

2) Attach the slot cover.

fAttach the stored slot cover to the blank slot, and tighten and x with

the four screws removed in Step 1).

Attention

fAlways attach the slot cover on the blank slot.

fStore the removed Interface Board inside an antistatic bag.

Specications

10 - ENGLISH

Specications

Compatible slot SLOT NX specication

Connection

terminals /

supported

signals

Inputs

BNC 4 lines

(<SDI 1 输入> terminal, <SDI 2 输入/1 输出> terminal, <SDI 3 输

入> terminal, <SDI 4 输入/3 输出> terminal)

Single link SD-SDI signal, SMPTE ST 259 standard compliant

Single link HD-SDI signal, SMPTE ST 292 standard compliant

Single link 3G-SDI signal, SMPTE ST 424 and 425-2 standards

compliant

Single link 6G-SDI signal, SMPTE ST 2081-1 and 2081-10

standards compliant

Supported by <SDI 1 输入>terminal and <SDI 3 输入>terminal only

Single link 12G-SDI signal, SMPTE ST 2082-1 and 2082-10

standards compliant

Supported by <SDI 1 输入>terminal and <SDI 3 输入>terminal only

Dual link HD-SDI signal, SMPTE ST 372 standard compliant

<SDI 1 输入> terminal: Link A signal /

<SDI 3 输入> terminal: Link B signal

Dual link 3G-SDI signal, SMPTE ST 425-3 standard compliant

<SDI 1 输入> terminal: Link 1 signal /

<SDI 3 输入> terminal: Link 2 signal

Dual link 6G-SDI signal, SMPTE ST 2081-11 standard compliant

<SDI 1 输入> terminal: Link 1 signal /

<SDI 3 输入> terminal: Link 2 signal

Quad link HD-SDI signal

<SDI 1 输入> terminal: Link 1 signal /

<SDI 2 输入/1 输出> terminal: Link 2 signal /

<SDI 3 输入> terminal: Link 3 signal /

<SDI 4 输入/3 输出> terminal: Link 4 signal

Quad link 3G-SDI signal, SMPTE ST 425-5 standard compliant

<SDI 1 输入> terminal: Link 1 signal /

<SDI 2 输入/1 输出> terminal: Link 2 signal /

<SDI 3 输入> terminal: Link 3 signal /

<SDI 4 输入/3 输出> terminal: Link 4 signal

Outputs

BNC 2 line (also functions as input terminal)

(<SDI 2 输入/1 输出> terminal, <SDI 4 输入/3 输出> terminal)

Performs active through output of the signals input to the <SDI 1

输入> terminal and <SDI 3 输入> terminal.

Dimensions

Width 151 mm (5-15/16")

Height 38.5 mm (1-17/32")

Depth 142 mm (5-19/32")

Weight 400 ] (14.1 ozs.)

Inhaltsverzeichnis

Andere Panasonic Computerhardware Handbücher

Panasonic

Panasonic 2SC1473 Bedienungsanleitung

Panasonic

Panasonic MAS3795E Bedienungsanleitung

Panasonic

Panasonic DV0PM20105 Bedienungsanleitung

Panasonic

Panasonic TY-FB11DD - Monitor Terminal Expansion Board Bedienungsanleitung

Panasonic

Panasonic AV-UHS5M6G Bedienungsanleitung

Panasonic

Panasonic 2SA2174J Bedienungsanleitung

Panasonic

Panasonic MICROCOMPUTER MN103S Montage- und Bedienungsanleitung

Panasonic

Panasonic 2SC4691G Bedienungsanleitung

Panasonic

Panasonic KX-TVM50 Bedienungsanleitung

Panasonic

Panasonic AJ-PCD35P Bedienungsanleitung

Panasonic

Panasonic CF-VEB471 Bedienungsanleitung

Panasonic

Panasonic CF-VEBC21Un Bedienungsanleitung

Panasonic

Panasonic WZ-AESDA Bedienungsanleitung

Panasonic

Panasonic ET-MDNHM10C Bedienungsanleitung

Panasonic

Panasonic ERB RD Bedienungsanleitung

Panasonic

Panasonic EXC24CB/CP Bedienungsanleitung

Panasonic

Panasonic WJ-PB85T08 Bedienungsanleitung

Panasonic

Panasonic WJPB65E01E - NETWORK BOARD FOR WJSX650 Bedienungsanleitung

Panasonic

Panasonic AJ-YA94G Bedienungsanleitung

Panasonic

Panasonic KX-W1500 Bedienungsanleitung

Panasonic

Panasonic 2SA1532 Bedienungsanleitung

Panasonic

Panasonic SH-AC300 Bedienungsanleitung

Panasonic

Panasonic TY-42TM6D - Monitor Terminal Expansion Board Bedienungsanleitung

Panasonic

Panasonic 2SA2078 Bedienungsanleitung

Beliebte Computerhardware Handbücher anderer Marken

EMC2

EMC2 VNX Series Betriebsanleitung

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Bedienungsanleitung

Gigabyte

Gigabyte B660M DS3H AX DDR4 Bedienungsanleitung

Raidon

Raidon iT2300 Bedienungsanleitung

National Instruments

National Instruments PXI-8186 Bedienungsanleitung

Hauppauge

Hauppauge WinTV-HVR-2250 Bedienungsanleitung

Kontron

Kontron CP6002 Bedienungsanleitung

Manhattan

Manhattan 702843 Bedienungsanleitung

Aphex

Aphex 230 Bedienungsanleitung

AMD

AMD Phenom II Betriebshandbuch

Intel

Intel NUC 12 Pro Bedienungsanleitung

dbx

dbx Zone Pro 1260 Bedienungsanleitung

Galaxy

Galaxy GHDX2-2430S-24F4D Bedienungsanleitung

Intel

Intel AXXRMFBU4 Bedienungsanleitung

Kontron

Kontron DIMM-PC/MD Bedienungsanleitung

ST X-NUCLEO-SAFEA1B Betriebsanleitung

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Bedienungsanleitung

Advantech

Advantech ASMB-935 Series Bedienungsanleitung