Panasonic KX-HTS Series Bedienungsanleitung

Setup Reference guide for KX-HTS Series

(Tested with HTS824 Version 1.5)

“LCR” SIP Trunk service

with Built-in Router

Version 0.1(PSN) 22th.June, 2017

Draft Version

SUMMARY

This document is a reference for configuring “LCR Telecom” SIP trunks onto Panasonic HTS and

includes the settings required for Incoming Call DDI routing and Outgoing Call CLI presentation.

SIP trunk specific account details are provided to you by LCR Telecom.

Attention:

This document was created based on the results of test environment accounts.

Panasonic cannot guarantee SIP Trunk operation in all environments, however as a result of

completing this Inter-Operability Test Panasonic will provide technical support for any issues

experienced an assist as far as possible in providing a resolution.

Please obtain relevant information from Service provider before configuration of SIP trunks.

Panasonic will not be held liable for any information provided in this guidance document.

Information used in this document is for interoperability testing.

Information and Specifications in this document are subject to change without notice.

Note

CLIR

HTS and LCR do not support CLIR (Anonymous).

CLIP when Transfer/Forward to CO

LCR does not support to notify the call originator CLI when call Transfer/Forward to CO.

Table of Contents

(1) SIP Trunk, Extension Port Number and NAT Configuration: Page 4

(2) Network Settings: Page 5

(3) Trunk Port Attribution: Page 7

(4) Provisioning a SIP trunk: Page 8

(5) Incoming Call Routing: Page 12

(6) Outgoing Call CLI: Page 13

(7) CLIR Outgoing Call (Anonymous calls): HTS Not supported Page 14

Built-in Router Example

HTS has a Built-in Router functions so advanced routing configuration can be managed by

the HTS and the internet router/modem simply providing internet access.

WAN Network: 10.0.0.0 / Subnet Mask: 255.255.255.248 (/24)

PBX assigned WAN-1 IP: 10.0.0.1

WAN Gateway IP Address: 10.0.0.6

Static DNS: Primary DNS Server 8.8.8.8 / Secondary DNS Server: 8.8.4.4

Note

Configure the settings according to the IP address system of the mapped WAN.

Also, set the IP address which does not duplicate other IP devices.

Internet

To Router/Modem

To PC/HUB

LAN1: 192.168.0.101/24

WAN1: 10.0.0.1/29

Router/Modem

(Enable DHCP)

KX0HDV series

(e.g., KX-HDV230)

HUB

(Gateway: 10.0.0.6/29)

WAN Directly Connected Network

(10.0.0.0/29)

(1) SIP Trunk, Extension Port Number and NAT Configuration

SIP Extension & SIP Trunk Common

Select [PBX Configuration] - [2. Extension] - [7.SIP Extension Property]

[SIP Extension & SIP Trunk Common]

1. Voice (RTP) UDP port No.(Server): Leave at 12000-

2. SIP Port Number: Leave at 5060

3. NAT Traversal: Leave Off

4. NAT – Fixed Global IP Address: Leave at 0.0.0.0

All other settings can be left at default.

Click [ Apply ]

Click [ Apply Now ]

(2) Network Settings

Network Configuration WAN Setting

Select [Network Configuration] - [3.WAN]– [1.WAN Setting] and Select [WAN 1 Channel]

Click [Modify]

HTS WAN-1 IP: 10.0.0.1 (Example)

Select the appropriate the Connection Type. In this example, use the Static IP address Option.

1. WAN Type: Fix IP

2. WAN Connection Name: Leave WAN1_Fix_IP - Reference only-

3. IP address, by your ISP: Enter your actual IP address

4. Subnet Mask: Enter your appropriate subnet mask

5. ISP Gateway Address: Enter the actual Gateway IP address

6. Static DNS Change to Enable

7. Primary DNS Server: Enter the actual DNS IP address

8. Secondary DNS Server: Enter the actual Secondary DNS IP address

Click [Apply]

LAN Settings

Go to [Network Configuration] - [4.LAN] - [2.LAN Settings]

1. IP Address: 192.168.0.101

2. Subnet Mask: 255.255.255.0

3. DHCP Mode: Server

[ DHCP server ]

4. IP Pool Staring Address: Leave 192.168.0.102

5. IP Pool Ending Address: Leave 192.168.0.254

6. Lease Time: Leave One day

(3) Trunk Port Attribution

Select [PBX Configuration] -[3.Trunk]- [1.Port] and click [Edit / CO Line Number 1 to 8]

[CO Line Number 1]

1. Attribution: SIP Carrier - 1

2. Trunk Group: Leave at 1

Click [Apply]

Click [Apply Now]

Example, Configure “CO-Line 1-2: SIP Carrier-1, Other CO-Line: No Connect”

SIP Trunk 2 Channels

Others 6 CO Line are not used,

Configure to No Connect from

Analog Line.

(4) Provisioning the SIP Trunk

SIP Trunk Property - Common

Select [PBX Configuration] - [3.Trunk] - [7. SIP Trunk Property] - [Common]

1. DNS SRV Record Resolve Ability: Leave Disable

[Register]

2. Register Sending Interval (s): Leave at 3600

3. Register Resending Interval (s): Leave at 300

4. RTCP Sending Interval (s): Leave at 5

SIP Trunk Property continued – SIP Carrier-1

[SIP Carrier-1]

1. Provider Name: Enter a name – reference only

2. SIP Server Name: trunksip2.lcrcom.es

3. SIP Server IP Address: Leave at 0.0.0.0

4. SIP Server port Number: 4399

5. SIP Server Domain: Not required

6. Subscriber Number: Not required

[Account]

7. User name:

Enter the

User name as supplied by LCR Telecom

(Note this is user name without @trunksip2.lcrcpm.es)

For example: Account (User name) =LCR201705301234567

Enter: LCR201705301234567

8. Authentication ID: Enter the Authentication ID as supplied by LCR Telecom

(Note this is user name without @trunksip2.lcrcpm.es)

For example: Authentication ID = LCR201705301234567

Enter: LCR201705301234567

9. Authentication Password:

Enter the

Authentication Password as supplied by LCR Telecom

For example: Authentication Password = passwordABCD

Enter: passwordABCD

[Register]

10. Register Ability: Enable

SIP Trunk Property continued – SIP Carrier-1

[Calling Party]

1. Header Type: Leave From Header

2. Host Name: Leave BLANK

3. Format: Leave Without “+”

4. Send CLIP of caller when call from SIP Leave Enable

Carrier is forwarded to same SIP carrier: *CLI will be converted to PBX No by LCR

[Called Party]

5. Format: Leave Without “+”

[Voice]

1. IP Codec Priority 1st: Leave G.711A

2. IP Codec Priority 2nd: Leave G.711Mu

3. IP Codec Priority 3rd: Leave None

4. Packet Sampling Time: Leave at 20 (ms)

5. DTMF: Leave Outband (RFC2833)

6. Payload Type (DTMF): Leave at 101

Andere Handbücher für KX-HTS Series

Inhaltsverzeichnis

Andere Panasonic Konferenzsystem Handbücher

Panasonic

Panasonic KX-VC300 Bedienungsanleitung

Panasonic

Panasonic KX-VC500CN Bedienungsanleitung

Panasonic

Panasonic KX-NS700G Bedienungsanleitung

Panasonic

Panasonic KX-TVP50 Bedienungsanleitung

Panasonic

Panasonic AFPX-COM5 Handbuch

Panasonic

Panasonic KX-VC300CN Bedienungsanleitung

Panasonic

Panasonic KX-VC300 Bedienungsanleitung

Panasonic

Panasonic KX-VC300CN Bedienungsanleitung

Panasonic

Panasonic KX-VC2000 Montageanleitung

Panasonic

Panasonic VoiceSonic KX-NT700 Bedienungsanleitung

Panasonic

Panasonic SC-GU3-02 Bedienungsanleitung

Panasonic

Panasonic WXT3020 - ORDER TAKER - MULTI LANGUAGE Bedienungsanleitung

Panasonic

Panasonic WX-C1011 Series Bedienungsanleitung

Panasonic

Panasonic KX-TDA100D Betriebsanleitung

Panasonic

Panasonic KX-HTS Series Bedienungsanleitung

Panasonic

Panasonic Attune WX-C3010 Bedienungsanleitung

Panasonic

Panasonic KXF-4T3C Bedienungsanleitung

Panasonic

Panasonic KX-VC1300 Bedienungsanleitung

Panasonic

Panasonic WX-CT2020 Bedienungsanleitung

Panasonic

Panasonic KX-VC500 Bedienungsanleitung

Panasonic

Panasonic WGAV120 - VIDEO TRANSMISSION Bedienungsanleitung

Panasonic

Panasonic SC-HG1-C Bedienungsanleitung

Panasonic

Panasonic KX-VC600 Bedienungsanleitung

Panasonic

Panasonic KX-TVS110 Bedienungsanleitung

Beliebte Konferenzsystem Handbücher anderer Marken

Kramer

Kramer VIA GO Bedienungsanleitung

ProSoft Technology

ProSoft Technology AN-X4-AB-DHRIO Bedienungsanleitung

Sony

Sony PCS-I150 Bedienungsanleitung

Middle Atlantic Products

Middle Atlantic Products VTC Series Bedienungsanleitung

AVT

AVT MAGIC AC1 Go Bedienungsanleitung

Prentke Romich Company

Prentke Romich Company Vanguard Plus Leitfaden

Speakerbus

Speakerbus iD 712 Bedienungsanleitung

Trelleborg

Trelleborg SafePilot CAT PRO Bedienungsanleitung

Sennheiser

Sennheiser ADN Bedienungsanleitung

ADTRAN

ADTRAN NetVanta 7100 Bedienungsanleitung

AINA

AINA PTT Voice Responder Bedienungsanleitung

Yamaha

Yamaha ProjectPhone PJP-100H Bedienungsanleitung

vissonic

vissonic VLI Series Bedienungsanleitung

Poly

Poly Trio 8300 Bedienungsanleitung

Crestron

Crestron Mercury CCS-UCA-SMK Maßzeichnung

Tenveo

Tenveo ALL-IN-ONE Bedienungsanleitung

AXIWI

AXIWI AT-350 Bedienungsanleitung

AT&T

AT&T Spirit Communications System Installationsanleitung