Panasonic AAD03011 Bedienungsanleitung
panasonic-electric-works.net/sunx
Elevator Door Controller AAD03011 Instruction Manual
8A3 708 0000 3
Panasonic Electric Works SUNX Shanghai
Panasonic Electric Works SUNX Shanghai
©Panasonic Electric Works SUNX Co., Ltd. 2010
8A3 708 0000 3
PRINTED IN CHINA
Panasonic Electric Works SUNX Shanghai Co., Ltd.
http://panasonic-electric-works.net/sunx
T52-3, No.1510, Chuanqiao Road, Jinqiao Export Processing Zone,
Pudong New Area, Shanghai, China
Phone: +86-21-5032-3800 FAX: +86-21-5032-3866
Europe Headquarter: Panasonic Electric Works Europe AG
Rudolf-Diesel-Ring 2, D-83607 Holzkirchen, Germany
Phone: +49-8024-648-0
US Headquarter: Panasonic Electric Works Corporation of America
629 Central Avenue New Providence, New Jersey 07974 USA
Phone: +1-908-464-3550
Elevator Door Controller
AAD03011
Instruction Manual
[Support model]
·AAD03011
Read this manual carefully before
attempting to operate the inverter
and store it for further reference.
ATTENTION
The inverter manufactured in our company is only applied to the elevator.
Use this equipment before ensuring the safety and application of the
elevator.
Always take safety precautions such as dual safety mechanism and
malfunction protection.
Failure to do so could lead to serious accident.
1
!
! Caution
Note
Foreword
Safety Precautions
This manual introduces the usage and precautions. Read the manual
carefully before using the product.
Precautions prescribed in this manual is divided into two grades:
Caution and Note.
The dangerous situations that could lead to moderate
or slight personal injury or property damage by
mishandling the equipment.
In addition, the precautions prescribed in Caution may lead to
serious situations in different conditions.
Please follow the information and instructions as laid out in this
manual carefully to avoid damage to equipment or risk to personal
injury.
The dangerous situations that could lead to personal
injury or death by mishandling the equipment.
Read this manual and related documents before attempting to install,
operate, service or inspect the inverter.
Make sure that you have an understanding of the device, the safety
information and all precautions before starting use.
Thank you for purchasing the AAD03011 inverter produced by Panasonic
Electric Works SUNX Shanghai Co., Ltd.
Note
!
1. Installation
2. Wiring
!Caution
Install the unit on a non-combustible material such as metal.
Installing it on other material could lead to fires.
Do not place the unit near flammable materials.
Doing so could lead to fires.
Do not hold by terminal cover during transportation.
Doing so could cause the unit to drop and lead to injuries.
Do not allow foreign matter such as metal swarf enter the unit.
Entry of this type of matter could lead to fires.
Install the unit according to the instruction manual on a place
where the weight can be withstood.
Failure to do so could lead to dropping of the unit and to injuries.
Do not install or operate an inverter that is damaged or missing parts.
Doing so could lead to injuries.
2
Always confirm that the input power is OFF before starting wiring.
Wait at least five minutes after turning the input power OFF before
starting use.
Failure to do so could lead to electric shocks or injuries.
Always connect the earth.
Failure to do so could lead to electric shocks or fires.
Wiring work must be carried out by a qualified technician.
Failure to do so could lead to electric shocks or fires.
Always install the unit before wiring.
Failure to do so could lead to electric shocks or injuries.
3
Note
!
!Caution
3. Operation
Do not connect an AC power supply to the output terminals (U, V, W).
Doing so could lead to injuries or fire.
Connect the correct wiring for the motor. If the wiring is incorrect,
the door control cannot operate properly.
Failure to do so could lead to injuries.
Connect the control terminals correctly. If the wiring is incorrect,
the door control cannot operate properly.
Failure to do so could lead to injuries.
Confirm that the product's rated voltage and the AC power supply
voltage match.
Failure to do so could lead to injuries or fire.
Tighten the terminal screws with the designated tool.
Failure to do so could lead to fire.
Always close the terminal cover before turning the input power ON.
Do not open the terminal cover while the power is ON.
Doing so could lead to electric shock.
Do not operate the buttons with wet hands.
Doing so could lead to electric shock.
Do not touch the inverter terminals when the inverter power is
ON or even when the inverter is stopped.
Doing so could lead to electric shock.
The STOP button is not designed for emergency stop purposes.
Prepare a separate emergency stop switches.
Failure to do so could lead to injury.
䋴
䈀㩷㩷㩷㩷㩷㩷㩷㩷㩷㩷㩷㩷㩷㩷㩷㩷㩷㩷㩷㩷㩷㩷㩷㩷㩷㩷㩷㩷䈁
Always confirm the security and function operation of the elevator
before obstacle detection function is applied.
Failure to do so could lead to injury.
Make sure to input safety sensor in the main controller of the elevator
and to operate the door's obstacle detection on the main controller side.
Obstacle detection function of the inverter does not operate in
CLOSE arrival area.
Always take dual security measures.
Failure to do so could lead to injury.
Make sure to input arrival signal (limit switch etc.)in the main controller
of the elevator and to operate the door's obstacle detection on the
main controller side.
Do not operate obstacle detection of the door only with OPEN/
CLOSE arrival signal (input signal and the relay's output signal).
Failure to do so could lead to injury.
Depending on different settings of the fault OPEN operation forced
operation time and the stop selection of OPEN/CLOSE operation,
sometimes even OPEN/ CLOSE signal are both turned OFF, the door
does not stop.
Confirm the elevator's security and function operation before using
this equipment.
(Secure personal safety before carrying out the operation.)
Failure to do so could lead to injury.
Depending on settings of the start mode and ride-through function
settings, if the run signal is ON or the power is restored after a power
failure, the inverter may start (restart) suddenly. Keep out of the working
part of the motor and the machine.
Design the machine so that personal safety can
be ensured even if the inverter starts suddenly.
Failure to so could lead to injury.
Depending on the start mode function setting, if "the fault trip is reset"
or "the stop state is released with the panel STOP function" or
"door width measurement is reset" when the run signal is input,
the inverter may restart suddenly.
(Secure personal safety before using this function.)
Failure to do so could lead to injury.
When the retry function is used, the inverter may automatically start(restart)
suddenly. Keep out of the working part of the motor and the machine.
(Secure personal safety before using this function.)
Failure to so could lead to injury.
4. Maintenance, Inspection and Part Replacement
5
Note
!
!Caution
The heat sink fins and brake resistor can reach high temperatures,
so do not touch them. Doing so could lead to burns.DŽ
The inverter can be easily set to run from low speeds to high speeds.
Confirm the tolerable range of the motor and machine before starting
operation.
Failure to do so could lead to injure.
Prepare holding brakes if required.
Failure to do so could lead to injure.
If there is no arrival signal, start operation before ensuring the
security and function operation of the elevator system.
(Secure personal safety before starting operation.)
Failure to do so could lead to injury.
When carrying out the door repeat control and the door width
measurement, the operation direction of the door may change
automatically. Start operation after ensuring personal safety.
Failure to do so could lead to injury.
Adjust and confirm each parameter before operating. Depending
on the settings of the parameters, the inverter may work unexpectedly.
Failure to do so could lead to injure.
Wait at least five minutes after turning the input power OFF before
starting inspections.
Failure to do so could lead to electric shock.
Maintenance, inspection and part replacement must be done by
qualified persons. [Remove all metal personal belongings
(watches, bracelets, etc.) before starting the work. ]
(Use tools treated with insulation.)
Failure to do so could lead to electric shocks or injury.
6. General Precautions
5. Others
Do not use the inverter for a load other than a three-phase
induction motor.
Never disassemble or modify the inverter. Doing so could lead
to electric shock or injury.
200V 0.4kW
WARNING
ELECTEIC SHOCK RISK˗
䃂
Disconnect supply and wait
䋵minutes before working on
this equipment.
䋣
7. Warning Lable on Inverter
[Inverter Surface]
6
Note
!
Caution
Have an electrician periodically tighten the terminal screws.
Loosening of the terminal screws could lead to overheating or fire.
All diagrams in this instruction manual show the state with the cover
or safety partitions removed to explain the details. Before operating
the product, replace the covers and partitions to the positions specified,
and operate the unit according to the instruction manual.
!
Table of Contents
8
Special Precautions 9䊶10
Installation 11
䇶Page䇷
Outline Dimensions 12
Parts Identification 13䌾15
Wiring (Main Circuit) 16䊶17
Wiring(Control Circuit) 18䌾22
Operation(Basic Operation) 23䌾28
Function of each modes 29䌾33
Setting and Changing Function 34䊶35
Functional Descriptions (Parameter Table) 36䌾40
Functional Descriptions (By parameters) 41䌾73
Operation procedure of Custom mode 74䌾75
Resetting Fault Trips 90
Troubleshooting 㽲91
Troubleshooting 㽳92
Maintenance and Inspection 93䊶94
Specifications 95䌾97
Supplementary Explanation of Door
Width Measurement
76
Supplementary Explanation of Obstacle
Detection Function of the Door
77
Supplementary Explanation of
Communication Function
78䌾88
Individual Details and Remedies for
Fault Trips
89䊶90
7
Points for Handling
Points for Handling
Follow this manual and precautions when handling the inverter.
Incorrect handling could lead to inhibited operation or a drop operating
life. In the worst case, the inverter could be damaged.
Power supply Use within + 10%, -15% of the tolerable input
voltage range, and within 㫧5% of the tolerable
input frequency range.
Circuit breaker
MCCB
Size a breaker from the selection table on page 17.
Magnet
contactor
MC
A magnet contactor is not required in normal
use. If installed, do not start or stop the inverter
with the magnet contactor.
Power factor
improvement
reactor
Connect this when the power factor must be
improved.
Input noise
filter
Connect this when noise to the peripheral
devices is a problem.
N䊶F
Inverter The ambient temperature is the most important
factor for the installation site. Make sure that the
tolerable value is not exceeded.
(See page 9 and 11)
Thermal relay
for open phase
protection
The thermal component built into the inverter is
used to protect against overloads. Use an open
phase protection thermal relay for open phase
protection.
Motor 3-phase induction motor.
8
Inhaltsverzeichnis
Andere Panasonic Controller Handbücher
Panasonic
Panasonic FP2 Series Bedienungsanleitung
Panasonic
Panasonic AFP7CPS Series Bedienungsanleitung
Panasonic
Panasonic CZ-256ESMC1U Bedienungsanleitung
Panasonic
Panasonic AKHRP900P - CAMERA CONTROLLER HC Bedienungsanleitung
Panasonic
Panasonic WVCU161C - SYSTEM CONTROLLER Bedienungsanleitung
Panasonic
Panasonic CZ-256ESMC3 Bedienungsanleitung
Panasonic
Panasonic MGSD Installationsanleitung
Panasonic
Panasonic CZ-256ESMC2U Bedienungsanleitung
Panasonic
Panasonic MGSDB2 Series Bedienungsanleitung
Panasonic
Panasonic FPS Series Bedienungsanleitung
Panasonic
Panasonic MINAS A6 Series Bedienungsanleitung
Panasonic
Panasonic FP0R Series Bedienungsanleitung
Panasonic
Panasonic AFP7MC16EC Bedienungsanleitung
Panasonic
Panasonic FP7 Series Bedienungsanleitung
Panasonic
Panasonic Minas A4 Series Bedienungsanleitung
Panasonic
Panasonic CZ-64ESMC3 Bedienungsanleitung
Panasonic
Panasonic GM1 Series Bedienungsanleitung
Panasonic
Panasonic HG-SC Bedienungsanleitung
Panasonic
Panasonic CZ-256ESMC2 Bedienungsanleitung
Panasonic
Panasonic FP7 Series Bedienungsanleitung
