Panasonic AW-RP50 Bedienungsanleitung

★ AW-RP50 controller can control up to five AW-HE40 cameras via the serial connection.

1. Connection

Connect one of AW-RP50 “T PAN/TILT HEAD” ports [1] – [5] and AW-HE40 “RS-422” port using a LAN cable

(Category 5 or higher, Straight cable, Up to 1,000m).

2. Setting Up AW-RP50

Example: Connection to AW-RP50 “T PAN/TILT HEAD” port [1]

① Press MENU button. – (Fig.3-A)

② Press [10] SYSTEM button. – (Fig.3-B) * “[1] CAMERA CTL” will be displayed on the LCD Panel. – (Fig.4)

* If it is not displayed, turn F1 dial – (Fig.3-C) to make “[1] CAMERA CTL” appear.

③ While “[1] CAMERA CTL” is displayed on the LCD, press F1 dial.

* “[1] CAM1” will be displayed on the upper half, and the connection method (default: [NoAsign]) on the lower

half of the LCD Panel. – (Fig.4)

④ Turn F2 dial – (Fig.3-D) to select [Serial], and then press F2 dial to determine the setting.

<Note>

・ Camera numbers CAM1 – CAM5 correspond to “T PAN/TILT HEAD” ports [1] – [5] on the Rear Panel,

respectively.

For example, if “T PAN/TILT HEAD” port [5] is used for serial connection, set [1] CAMERA CTL > 5. CAM5

to [Serial].

③Press F1

(LAN Cable)

Controlling AW-HE40 with AW-RP50 (vi Seri l Connection)

(Figure 4: LCD Panel)

（A）

（B）

（C）

（D）

(Figure 3: AW-RP50 Control Panel)

(Figure 1: AW-RP50 Rear Panel) (Figure 2: AW-HE40 Rear Panel)

［1］CAMERA CTL

①MENU N => ②Select [10]

④Turn F2 to select

=> Press F2 to set

1．CAM1

NoAsign

1．CAM1

Seri l

・ The [Serial] setting for serial connection cannot be set for camera numbers CAM6 – CAM100.

3. Turning On AW-HE40

★ After the setting-up is completed, LED button 1 at AW-RP50 CAMERA STATUS / SELECTI N Area – (Fig.5) lights

up according to the camera’s power status. If the camera is in STANDBY mode (power FF: factory default), it

lights up in orange. If in P WER N mode (power N), it lights up in green.

★ When the camera is in STANBY mode, follow the procedure below to turn on the camera.

Example: Switching over to P WER N mode (power N) on AW-HE40 connected to CAM1

① Hold down LED button 1 at CAMERA STATUS/SELECTI N. – (Fig.6-A)

* While the button is held down, the selected camera and its power status will be displayed on the LCD Panel. –

(Fig.7)

② Keeping the button held down, turn F2 dial – (Fig.6-B) to select “ N”. Then press F2 dial to determine it.

* By this operation, AW-HE40 will be switched over to P WER N mode after its default setting motion.

(The status lamp will light up in green and the LED on AW-RP50 will also light up in green.)

* In P WER N mode, if you follow the same procedure and select [P WER: FF], AW-HE40 will be switched

over to STANBY mode.

CAM1＜AW-HE40 ＞

POWER

：

OFF

CAM1＜AW-HE40 ＞

POWER

：

“C

AM1”

is held down

Select “ N” => Press F2 to determine

Turn F2

After setting up, this lights up

according to the camera’s

power status.

* If it does not light up, please check the following points.

（A）

(Figure 6: AW-RP50 Control Panel)

(Figure 7: LCD Panel)

（B）

① Check the connection state of LAN cable or whether you are using a cable that meets the specifications.

② Check that the LAN cable is connected to “RS-422 port”, not to “LAN port”.

③ Double-check that there is no error in setting up the connection.

(Figure 5: AW-RP50 CAMERA STATUS/SELECTI N Area)

Andere Handbücher für AW-RP50

Inhaltsverzeichnis

Andere Panasonic Controller Handbücher

Panasonic

Panasonic AWRP605P - MULTI FUNCTION CONTROLLER Bedienungsanleitung

Panasonic

Panasonic CZ-256ESMC2 Bedienungsanleitung

Panasonic

Panasonic AW-HHD100E Bedienungsanleitung

Panasonic

Panasonic CZ-ANC3 Bedienungsanleitung

Panasonic

Panasonic WVCU161C - SYSTEM CONTROLLER Bedienungsanleitung

Panasonic

Panasonic AKHRP900P - CAMERA CONTROLLER HC Bedienungsanleitung

Panasonic

Panasonic FP2-PP2T Bedienungsanleitung

Panasonic

Panasonic WVCU950 - CONTROLLER - ADDENDUM Bedienungsanleitung

Panasonic

Panasonic CZ-256ESMC3 Bedienungsanleitung

Panasonic

Panasonic AW-RP605AN Bedienungsanleitung

Panasonic

Panasonic PAW-HPM 1 Bedienungsanleitung

Panasonic

Panasonic Vossloh-Schwabe Light Controller IP/DALI 2CH Bedienungsanleitung

Panasonic

Panasonic AFPXHEAD4 Bedienungsanleitung

Panasonic

Panasonic fp2/fp2sh Bedienungsanleitung

Panasonic

Panasonic S-Link FP2 Bedienungsanleitung

Panasonic

Panasonic WV-CU980/G Bedienungsanleitung

Panasonic

Panasonic MINAS A5 Series Bedienungsanleitung

Panasonic

Panasonic FV-SW20VEC1 Bedienungsanleitung

Panasonic

Panasonic FP3 Bedienungsanleitung

Panasonic

Panasonic FP0 Series Bedienungsanleitung

Panasonic

Panasonic FP7 Series Bedienungsanleitung

Panasonic

Panasonic TY-FB12LC Bedienungsanleitung

Panasonic

Panasonic FP OPC Server Bedienungsanleitung

Panasonic

Panasonic CZ-64ESMC3 Bedienungsanleitung

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Rockwell Automation

Rockwell Automation 1769-L31 Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

Emerson

Emerson SW93 Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Samson

Samson Type 5824 Service-Handbuch

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Siemens

Siemens OpenAir GMA 1 Series Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Fishman

Fishman TriplePlay Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung

3M MicroTouch EX113 Bedienungsanleitung

KUHN

KUHN TKS Bedienungsanleitung