Panasonic FV-10NLF1E Bedienungsanleitung

INSTALLATION INSTRUCTIONS

In-Line Fan

Model No. FV-10NLF1E FV-20NLF1 FV-30NLF1 FV-40NLF1

FV-10NLF1E

FV-20NLF1

FV-30NLF1

FV-40NLF1

READ AND SAVE THESE INSTRUCTIONS

Thank you for purchasing this Panasonic product.

Please read these instructions carefully before attempting to install, operate or service the

Panasonic product. Failure to comply with instructions could result in personal injury or

property damage. Please explain to users how to operate and maintain the product after

installation, and this booklet should be presented to users.

Please retain this booklet for future reference.

Contents

GENERAL SAFETY INFORMATION ....................................2~3

DESCRIPTION ......................................................................... 4

UNPACKING........................................................................... 4

SUPPLIED ACCESSORIES ........................................................ 4

DIMENSIONS.......................................................................... 5

INSTALLATION I (HORIZONTALLY BETWEEN JOISTS)......5~7

INSTALLATION II (ON CEILINGS/JOISTS) .............................. 7

INSTALLATION III (VERTICALLY ON JOISTS OR PILLARS) .... 8

MAINTENANCE...................................................................... 9

PRACTICAL GUIDE TO INSTALLATION.................................. 9

SPECIFICATIONS................................................................... 10

PRODUCT SERVICE .............................................................. 10

GENERAL SAFETY INFORMATION

For Your Safety

To reduce the risk of injury, loss of life, electric shock, fire, malfunction, and damage to equipment or

property, always observe the following safety precautions.

Explanation of symbol word panels

The following symbol word panels are used to classify and describe the level of hazard, injury, and

property damage caused when the denotation is disregarded and improper use is performed.

WARNING Denotes a potential hazard that could result in serious injury or

death.

CAUTION Denotes a hazard that could result in minor injury.

The following symbols are used to classify and describe the type of instructions to be observed.

This symbol is used to alert users to a specific operating procedure that must be followed in

order to operate the unit safely.

This symbol is used to alert users to a specific operating procedure that must not be

performed.

This symbol is used to alert users not to disassemble the equipment.

This symbol is used to alert users to make sure of grounding when using the equipment with

the grounding terminal.

WARNING

To reduce the risk of fire, electric shock or personal injury, observe the following:

Use this unit only in the manner intended by the manufacturer. If you have any questions,

contact the manufacturer.

Installation work and electrical wiring must be done by qualified person(s) in accordance with

all applicable codes and standards, including fire-rated construction.

Sufficient air is needed for proper combustion and exhausting of gases through the flue

(chimney) of fuel burning equipment to prevent backdrafting. Follow the heating equipment

manufacturer’s guidelines and safety standards such as those published by the National

Fire Protection Association (NFPA), the American Society for Heating Refrigeration and Air

Conditioning Engineers (ASHRAE) and the local code authorities.

When cutting or drilling into a wall or ceiling, do not damage electrical wiring and other

hidden utilities.

Ducted fans must always be vented to the outdoors.

Do not use this unit with any solid-state control device.

Before servicing or cleaning unit, switch power off at service panel and lock the service

disconnecting mains to prevent power from being switched on accidentally. When the service

disconnecting mains cannot be locked, securely, fasten a prominent warning device, such as a

tag, to the service panel.

GENERAL SAFETY INFORMATION

WARNING

Not to be installed in a ceiling thermally insulated to a value greater than R40. (This is required

for installation in Canada only.)

Never place a switch where it can be reached from a tub or shower.

A statement to the effect that when the product is to no longer be used, it must not be left in

place but removed, to prevent it from possibly falling.

Do not disassemble the unit for reconstruction. It may cause fire or electric shock.

Ceiling joist must be subjected to static load more than five times the weight of the product.

This product must be grounded.

CAUTION

Do not install this In-Line Fan where the temperature may exceed 60℃(140°

F).

Make certain that the service supply voltage is 120V, 60Hz.

Follow all local electrical and safety codes as well as

the National Electrical Code (NEC) and the Occupation

Safety and Health Act (OSHA).

Always switch the power source off before working on

or near the fan or motor.

Protect the electrical wires from sharp edges, oil, grease,

hot surfaces, chemicals, or other objects.

Do not bend the electrical wires.

Do not install the unit where ducts are configured as

shown in Fig.A.

Provide suction parts with proper ventilation.

For general ventilating use only. Do not use to exhaust

hazardous or explosive materials or vapours.

Before installation, confirm that the unit is facing the

right direction. (Fig.B)

Do not drop the unit, put it on the hanger securely.

The special-purpose or dedicated parts, such as

mounting fixtures, must be used if such parts are

provided.

Fig.A

Fig.B

direction

DESCRIPTION

These Panasonic In-Line Fan models use a sirocco fan driven by a capacitor motor.

The motor is designed to have an extended service life with reduced energy consumption, and a

reduced noise level.

It also incorporates a thermal cutout for safety.

UNPACKING

Unpack and carefully remove unit from carton.

Refer to the supplied accessories list to verify that all parts are present.

SUPPLIED ACCESSORIES

Part name Illustration Quantity

Bracket 2

Hanger 1

Bracket cover 2

Installation bracket 2

Extension bracket 2

Holder

(Assembled on body) 2

Long screw 10

Self-tapping screw 12

Short screw 4

AIR FLOW

No. Part name No. Part name

Motor Inspection panel

Body Bracket cover

Adapter Installation bracket

Fan Extension bracket

Junction box Bracket

Junction box cover Holder

Model No. A B C D E F G H I J

FV-10NLF1E 340

(13 3/8)

240

(9 7/16)

440

(17 5/16)

200

(7 7/8)

38.1

(1 1/2)

(5/16)

321-581

(12 5/8-22 7/8)

242

(9 17/32)

∅97

(∅3 13/16)

∅112

(∅4 13/32)

FV-20NLF1 340

(13 3/8)

240

(9 7/16)

550

(21 21/32)

240

(9 7/16)

38.1

(1 1/2)

(5/16)

321-621

(12 5/8-24 7/16)

242

(9 17/32)

∅142

(∅5 19/32)

∅158

(∅6 7/32)

FV-30NLF1 390

(15 11/32)

270

(10 5/8)

600

(23 5/8)

280

(11 1/32)

38.1

(1 1/2)

(5/16)

321-661

(12 5/8-26)

242

(9 17/32)

∅142

(∅5 19/32)

∅158

(∅6 7/32)

FV-40NLF1 420

(16 17/32)

340

(13 3/8)

560

(22 1/6)

280

(11 1/32)

38.1

(1 1/2)

(5/16)

321-661

(12 5/8-26)

242

(9 17/32)

∅195

(∅7 11/16)

∅211

(∅8 5/16)

Dimensions: mm(inch)

Fig. 1

Ceiling joist

Hanger Long Screw

Ceiling board

INSTALLATION I (HORIZONTALLY BETWEEN JOISTS)

1. Disconnect the power to the receptacle before

starting the installation.

2. Fix the hanger to the ceiling joist. Keep

distance “A” between the hanger and ceiling

board (table 1). Use two long screws to fasten

the hanger. (Fig.1)

Dimension: mm(inch)

MODEL FV-10NLF1E FV-20NLF1 FV-30NLF1 FV-40NLF1

165

(6 1

165

(6 1

185

(7 1

215

(8 1

(table 1)

DIMENSIONS





 







3. After confirming the direction that the unit

will be facing, attach the bracket and bracket

cover to the unit with self-tapping screws.

(Fig.2)

CAUTION

The holder was assembled on the back

side of the unit. (no shown in Fig.2)

Attach the unit body horizontally to the

panel of your choice.

For best results, the bracket and bracket

cover should be attached vertically.

The holder and the bracket should be

installed on the same side of the joist.

4. Insert installation bracket into bracket cover.

If joist space is greater than distance B at the

center (table 2), attach installation bracket and

extension bracket as shown below.

Installation

bracket

Extension

bracket

Short

screw

Dimension: mm(inch)

MODEL FV-10NLF1E FV-20NLF1 FV-30NLF1 FV-40NLF1

B381

(15)

421

(16 1

461

(18 1

461

(18 1

(table 2)

5. Insert the holder, located on the unit, into the

hanger. (Fig.3)

6. Attach the In-Line Fan to a joist or a pillar with

the long screws. (Fig.4)

7. Remove junction box cover and secure conduit

or wire holder to junction box cover knockout

hole. (Fig.5)

8. Using wire nuts, connect house power wire as

shown in the wiring diagram.

9. Replace junction box cover.

CAUTION

Mount junction box cover carefully so

that wires are not pinched.

Fig. 2

Self-tapping

screws

Bracket Bracket

cover

Fig.4

Circular duct

Ceilling

joist

Conduit

Long

Screw

Long

Screw

Green wire

Cord clip

Junction box

Red wire

Blue wire

Condenser

White

Black

Conduit

Wire nut

Junction box cover Fig.5

INSTALLATION I (HORIZONTALLY BETWEEN JOISTS)

Fig. 3

INSTALLATION I (HORIZONTALLY BETWEEN JOISTS)

Wiring Diagram

(Fuse in Motor

FV-10NLF1E:134°C

FV-20NLF1:167°C

FV-30NLF1:134°C

FV-40NLF1:134°C)

Thermally - protected

Motor Red

Blue

Black

White

Green

Junction box

Power

Supply

120V~

60Hz

Capacitor

Fan body

Earth ground

10.Install circular ducts (on both ends) and secure

them with tape or clamps.

Consult table 3 for the appropriate duct sizes.

Dimension: mm(inch)

MODEL FV-10NLF1E FV-20NLF1 FV-30NLF1 FV-40NLF1

duct ∅102

(4)

152

(6)

152

(6)

203

(8)

(table 3)

11. Connect power line to receptacle after finshing

duct work.

INSTALLATION II (ON CEILINGS/JOISTS)

1. Attach installation bracket and bracket to the

unit body. (Fig.6)

CAUTION

Insert the installation bracket into the

bracket cover attached to the panel.

2. Extend installation bracket and put the unit

on the ceiling or joist. Secure with long screws.

(Fig.7)

3. Remove junction box cover and secure conduit

or wire holder to junction box cover knockout

hole. (Fig.5)

4. Using wire nuts, connect house power wire as

shown in the wiring diagram on page 7.

5. Replace junction box cover.

CAUTION

Mount junction box cover carefully so

that wires are not pinched.

6. Install circular ducts (on both ends) and secure

them with tape or clamps.

Consult table 3 for the appropriate duct sizes.

Dimension: mm(inch)

MODEL FV-10NLF1E FV-20NLF1 FV-30NLF1 FV-40NLF1

duct ∅102

(4)

152

(6)

152

(6)

203

(8)

(table 3)

Long screw

Circular duct

Long screw

Ceiling joist

Fig.7

Fig.6

Installation

bracket

Bracket

Green wire

Cord clip

Junction box

Red wire

Blue wire

Condenser

White

Black

Conduit

Wire nut

Junction box cover Fig.5

INSTALLATION III (VERTICALLY ON JOISTS OR PILLARS)

Installing the In-Line Fan requires an accessible

area (attic or air extraction apparatus)

1. Install the In-Line Fan using the first step

described in INSTALLATION II.

2. Extend installation bracket and hang the unit

on the joist or piller. Fix with the long screws.

(Fig.8)

CAUTION

Be careful not to drop the unit.

3. Remove junction box cover and secure conduit

or wire holder to junction box cover knockout

hole. (Fig.5)

4. Using wire nuts, connect house power wire as

shown in the wiring diagram.

5. Replace junction box cover.

CAUTION

Mount junction box cover carefully so

that wires are not pinched.

Wiring Diagram

(Fuse in Motor

FV-10NLF1E:134°C

FV-20NLF1:167°C

FV-30NLF1:134°C

FV-40NLF1:134°C)

Thermally - protected

Motor Red

Blue

Black

White

Green

Junction box

Power

Supply

120V~

60Hz

Capacitor

Fan body

Earth ground

6. Install circular ducts (on both ends) and secure

them with tape or clamps.

Consult table 3 for the appropriate duct sizes.

Dimension: mm(inch)

MODEL FV-10NLF1E FV-20NLF1 FV-30NLF1 FV-40NLF1

duct ∅102

(4)

152

(6)

152

(6)

203

(8)

(table 3)

Fig.6

Installation

bracket

Bracket

Long screw Fig.8

Green wire

Cord clip

Junction box

Red wire

Blue wire

Condenser

White

Black

Conduit

Wire nut

Junction box cover Fig.5

MAINTENANCE

PRACTICAL GUIDE TO INSTALLATION

WARNING

Disconnect power line before proceeding

with repairs or maintenance.

CAUTION

Never use benzene based thinner or

similar chemicals for cleaning the In-Line

Fan.

Do not allow water to come into contact

with the motor.

Do not immerse resin parts in water where

the temperature is over 60℃(140°

F).

1. Remove inspection panel (take off the screws

and pull). (Fig.9)

2. Clean inspection panel (do not immerse in

water), wipe dry with cloth.

3. Remove dust and dirt inside the fan’s body

using a vacuum cleaner. (Fig.10)

4. Using a cloth dampened with kitchen

detergent, remove any dirt from the fan’s

body. Wipe dry with a cloth (do not wipe

thermal insulation parts inside body with

dampened cloth).

5. Replace inspection panel. Fig.10

Cleaner

Inspection panal

Fig.9

Properly insulate the area around the fan to

minimize building heat loss and gain. (Fig.11)

Loose fill or batt insulation can be placed directly

over the fan housing in the attic. Our fans

and fan/light combination units do not create

excessive heat that is a common problem with

recessed light fixtures or some competitor’s fan/

light combination. Our efficient, cool-running

motors and our fluorescent lamps do not create

enough ambient heat to be subjected to these

limitations. The ducting from this fan to the

outside of the building has a strong effect on the

air flow, noise and energy use of the fan. Use

the shortest, straightest duct routing possible for

best performance, and avoid installing the fan

with smaller ducts than recommended. Insulation

around the ducts can reduce energy loss and

inhibit mold growth. Fans installed with existing

ducts may not achieve their rated air flow.

Fig.11

Insulation

Foil tape tightly

covers all metal

duct joints.

(Glue PVC joints)

A short piece of flexible

duct helps alignment

and absorbs sound.

Use clamps plus mastic

or approved foil faced

tape at all flex joints.

4, 6 or 8 inch roof jack,

wall cap, or soffit vent

with backdraft damper

Mechanically connect duct to

termination and seal with mastic

or approved foil faced tape

2-3 ft straight run before elbow

In attic installation,

caulk box to drywall

PRODUCT SERVICE

Warning Concerning Removal of Covers.

The unit should be serviced by qualified technicians only.

Your product is designed and manufactured to ensure a minimum of maintenace.

Should your unit require service or parts, call Panasonic Call Center at 1-866-292-7299(USA)

Or 1-800-669-5165(Canada).

Panasonic Corporation of North America

Two Riverfront Plaza, Newark, NJ 07102

www.panasonic.com

Panasonic Canada Inc.

5770 Ambler Drive, Mississauga, Ontario L4W 2T3

www.panasonic.ca

Printed in China

P0502-60915 10NLF10750F

Model No. Air

direction V Hz

Power

consumption

(W)

Speed

(PRM)

Air delivery

(CFM)

Weight

Kg(lb.)

FV-10NLF1E

Exhaust 120 60

30 1510 120 6.3(13.9)

FV-20NLF1 57 1260 240 7.5(16.5)

FV-30NLF1 98 1340 340 10.9(24.1)

FV-40NLF1 132 1150 440 11.9(26.3)

SPECIFICATIONS

*Power consumption, speed and air delivery values have been measured at 5mm WG (0.2’’ WG).

Andere Handbücher für FV-10NLF1E

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Panasonic Lüfter Handbücher

Panasonic

Panasonic F-BR251 Bedienungsanleitung

Panasonic

Panasonic WhisperGreen FV-08VKM3 Bedienungsanleitung

Panasonic

Panasonic FY-650ZDY8 Technisches Handbuch

Panasonic

Panasonic F-M14HW Bedienungsanleitung

Panasonic

Panasonic FY-E15PM1 Technisches Handbuch

Panasonic

Panasonic FV-15NLFS1 Bedienungsanleitung

Panasonic

Panasonic F-M15GW Bedienungsanleitung

Panasonic

Panasonic ECONAVI F-M15H5VBSQH Bedienungsanleitung

Panasonic

Panasonic F-70ZBR Bedienungsanleitung

Panasonic

Panasonic F-30SMH Bedienungsanleitung

Panasonic

Panasonic WhisperGreen FV-08VKML3 Bedienungsanleitung

Panasonic

Panasonic F-50KU1 Bedienungsanleitung

Panasonic

Panasonic WhisperLite FV-08VQL6 Bedienungsanleitung

Panasonic

Panasonic FV-05-11VKS1 Kurzanleitung

Panasonic

Panasonic Whisper Value-Lite FV-08VSL2 Bedienungsanleitung

Panasonic

Panasonic FV-0811RQ1 Bedienungsanleitung

Panasonic

Panasonic FV-04WS2 Bedienungsanleitung

Panasonic

Panasonic FV-05VF2 Bedienungsanleitung

Panasonic

Panasonic F-M15A0 Bedienungsanleitung

Panasonic

Panasonic F-60UFN Bedienungsanleitung

Panasonic

Panasonic FV-15AUL1 Bedienungsanleitung

Panasonic

Panasonic Intelli-Balance 100 Bedienungsanleitung

Panasonic

Panasonic FV-05VS1 Bedienungsanleitung

Panasonic

Panasonic F-60SVN Bedienungsanleitung

Beliebte Lüfter Handbücher anderer Marken

ELTA FANS

ELTA FANS H03VV-F Bedienungsanleitung

Hunter

Hunter 20714 Gebrauchsanweisung

Emerson

Emerson CARRERA VERANDA CF542ORB00 Bedienungsanleitung

Hunter

Hunter Caraway Gebrauchsanweisung

Kompernass

Kompernass KH 1150 Bedienungsanleitung

VES

VES FALA100/12V/TR Bedienungsanleitung

Vertiv

Vertiv Liebert DCD Bedienungsanleitung

Westinghouse

Westinghouse GFP Series Bedienungsanleitung

Venmar

Venmar KUBIX HRV PLUS Series Bedienungsanleitung

Maico

Maico ECR 31 Bedienungsanleitung

Sonnenkonig

Sonnenkonig Dinky Bedienungsanleitung

S&P

S&P ECOWATT HXBR Bedienungsanleitung

Wider

Wider IMP03369BH Bedienungsanleitung

Hinkley

Hinkley HIGHLAND Bedienungsanleitung

Broan

Broan 766BN Bedienungsanleitung

Premium

Premium PFS16022 Montageanleitung

Litex Industries

Litex Industries E-CGL52CB5C1 Bedienungsanleitung

Lindab

Lindab LTDF Bedienungsanleitung