Panasonic FV-15NLFS1 Bedienungsanleitung

PRACTICAL GUIDE TO INSTALLATION

FV-15NLFS1

CONTENTS

GENERAL SAFETY INFORMATION

DESCRIPTION

UNPACKING

SUPPLIED ACCESSORIES

DIMENSIONS

INSTALLATION

Model No.

2~4

OPERATION 9~10

10~11

6~8

MAINTENANCE

SPECIFICATIONS

PRODUCT SERVICE

READ AND SAVE THESE INSTRUCTIONS

Thank you for purchasing this Panasonic product.

Please read these instructions carefully before attempting to install, operate or service the

Panasonic product. Please carefully read the “GENERAL SAFETY INFORMATION” (P.2~4) of

this manual before use. Failure to comply with instructions could result in personal injury or

property damage. Please explain to users how to operate and maintain the product after

installation, and this booklet should be presented to users.

Please retain this booklet for future reference.

Installation and Operating Instructions

In-Line Fan

This symbol is used to alert users not to disassemble the equipment.

Do not disassemble the product for reconstruction. It may cause fire or electric shock.

Use this unit only in the manner intended by the manufacturer. If you have any

questions, contact the manufacturer.

Installation work and electrical wiring must be done by qualified person(s) in

accordance with all applicable codes and standards, including fire-rated construction.

Do not install with a method which is not approved in the instructions.

Do not use this product with any solid-state control device. Solid-state controls may

cause harmonic distortion which can cause motor humming noise.

This symbol is used to alert users to a specific operating procedure that must be

followed in order to operate the product safely.

This symbol is used to alert users to a specific operating procedure that must not be

performed.

This symbol is used to alert users to make sure of grounding when using the

equipment with the grounding terminal.

For Your Safety

Explanation of symbol word panels

To reduce the risk of injury, loss of life, electric shock, fire, malfunction, and damage to

equipment or property, always observe the following safety precautions.

The following symbols are used to classify and describe the type of instructions to be

observed.

The following symbol word panels are used to classify and describe the level of hazard, injury,

and property damage caused when the denotation is disregarded and improper use is

performed.

CAUTION

Denotes a potential hazard that could result in death or

serious injury.

Denotes a hazard that could result in minor injury.

Denotes a hazard that could result in property damage.

WARNING

GENERAL SAFETY INFORMATION

NOTICE

TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR PERSONAL INJURY, OBSERVE THE

FOLLOWING :

Before servicing or cleaning product, switch power off in control box and lock the

service disconnecting means to prevent power from being switched on accidentally.

When the service disconnecting means cannot be locked, securely fasten a prominent

warning device, such as a tag, to the service panel.

When cutting or drilling into ceiling, do not to damage metal objects, electrical

wiring and other hidden utilities.

Ducted fans must always be vented to the outdoors.

Ceiling must be subjected to static load more than five times the weight of the product.

A statement to the effect that when the product is to no longer be used, it must

not be left in place but remove, to prevent it from possibly falling.

Do not kink the power cord. Maintenance board

to be upside

Never place a switch where it can be reached from a tub or shower.

The product must be properly grounded.

Make certain that the electric service supply voltage

is AC 120 V, 60 Hz.

Put the product on the hanger securely. Otherwise, it

may drop.

Protect the power cord from sharp edges, oil, grease,

hot surfaces, chemicals or other objects.

Do not install the product as the directions

shown in right. Otherwise, it may cause electric

shock.

(Fig.A)

Follow all local electrical and safety codes, as well as

the National Electrical Code (NEC) and the

Occupational Safety and Health Act (OSHA).

Always disconnect the power source before working

on or near the fan or motor.

Sufficient air is needed for proper combustion and exhausting of gases through the

flue (chimney) of fuel burning equipment to prevent backdrafting. Follow the heating

equipment manufacturer’s guideline and safety standards such as those published by

the National Fire Protection Association (NFPA), and the American Society for Heating

Refrigeration and Air Conditioning Engineers (ASHRAE) and the local code authorities.

Install this product in the area where the temperature

is between14 °F (-10 °C)~104 °F (40 °C).

CAUTION

GENERAL SAFETY INFORMATION

The special-purpose or dedicated parts, such as

mounting fixtures, must be used if suchparts are

provided.

Floor

Cooking

equipment

(Cooking area)

Do not install above or

inside this area

Fig. B

Fig. A

Not for use in cooking area. (Fig.B)

This fan shall not be installed behind a suspended floor/

ceiling or a structural wall, ceiling, or floor.

Please install the tube cover or similar items at the air inlet, otherwise it may cause the

entry of foreign matter or rain, affecting product performance.

Do not install the product where ducts are configured as shown below.

Adaptor

Excessive bending Successive bending Squeezed duct Bend close to duct adaptor

GENERAL SAFETY INFORMATION

NOTICE

This product uses a sirocco fan driven by a DC motor powered by an integral transformer.

The motor is designed to have long operating life, high dynamic response, higher speed

ranges with saving energy. The blower uses a high-capacity sirocco fan developed to reduce

the noise level.

Unpack and remove product carefully from carton.

Refer to the supplied accessories list to verify that all parts are present.

DESCRIPTION

UNPACKING

Part name Appearance Quantity

Hanger

Installation and

operating instructions

Limited warranty

Unit : inch (mm)

Screw

(M4X8)

SUPPLIED ACCESSORIES

DIMENSIONS

15 3/4 (399) 8 3/4 (223)

23 3/8 (594 )

11 (282)

Φ5 7/8 (148)

3 3/4 (97)

Φ5 7/8 (148) 4 3/8 (112)

4 3/8 (112)

4 5/8 (119)

1 2

910 8

Part nameNo. Part nameNo.

Main PCB

Maintenance board

Adaptor

Pre-filter

Air

flow

Sub-efficient filter

Damper

Motor

Power cord

Sirocco fan

Control box cover

3 3/4 (97)

Unit : inch (mm)

1-1 Install with the maintenance board towards down

INSTALLATION

You can install the product with maintenance board towards down or towards side. (Fig.1,

Fig.2) If there are joists on ceiling, you should install it with the maintenance board towards

down, otherwise you may can not to maintain filter.

1. Fix the hangers (3 pcs) on fan body by screws.

(Fig.3)

2.Install hanger bolts on ceiling, and put washers

and nuts on bolts. (Hanger bolt, nut and washer

should be M8-M10 and no provided.) (Fig.4)

3.Install the product on hanger bolts and fix the

nuts tightly. (Fig.5)

Please use the spirit level to adjust the body, to

ensure that the height of the three hangers

within ± 2 mm.

(Not applicable for ceiling with joists)

3-Hanger

bolts

Hanger

Maintenance board towards down

Maintenance

board

Maintenance

board

Hanger

(Fix by 4

screws)

Hanger (Fix

by 3 screws)

Hanger (Fix by 3 screws)

Before installing please choose the installation direction.

Maintenance board towards side

Nut

Ceiling

Washer

Nut

10 1/2 (267)

3 1/2 (90)

1/2 (12)

1 (25)

6 3/8 (162)

7 (182)

Note

Fig.1 Fig.2

Fig.3

Fig.4

Fig.5

7/8 (22) 7/8 (22)

2 7/8 (74)

INSTALLATION

Unit : inch (mm)

4.Install Φ6 inch ducts.

5.Set an square inspection hole

of 450 mm or more under the

maintenance board. (Fig.7)

6.Twist hand screw open maintenance board and pull out the sub-efficient filter,

fill in beginning time on sub-efficient filter, then install back. (Refer Fig.13~15 on P.10~11)

Square inspection hole

Square inspection hole CeilingCeiling

(1) Connect the circular duct (suggest using

the insulated flexible duct) to adaptor by

mastic or approved foil tape.

Hanger

Install the exterior duct with a declining

slope toward outer side at least 1/100.

Install the interior duct with a declining

slope toward inner side at least 1/100.

(Fig.6)

Note

Fiberglass insulation

Fig.7

17 3/4 (450) 1 5/8 (40)

>1 1/4 (30)

17 3/4 (450)

Exterior duct

Interior duct Mastic or

approved foil

tape

Mastic or

approved foil

tape

Adaptor

Fig.6

Place/wrap insulation around duct and/or

fan in order to minimize possible

condensation buildup within the duct.

(Fig.6)

Unit : inch (mm)

6.Twist hand screw open maintenance board and pull out the sub-efficient filter, fill in

beginning time on sub-efficient filter, then install back. (Refer Fig.13~15 on P.10~11)

Maintenance

board

Hanger (Fix

by 3 screws)

Hanger (Fix by

4 screws)

Hanger (Fix by

3 screws)

This method can not applicable for ceiling

with joists.

4 3/8 (110)

3 1/2 (90)

17 1/2 (443)

1-2 Install with the maintenance board towards side

INSTALLATION

1. Fix the hangers (3 pcs) on fan body by screws.

(Fig.8)

2.Install hanger bolts on ceiling, and put washers

and nuts on bolts. (Hanger bolt, nut and washer

should be M8-M10 and no provided.) (Fig.9)

3.Install the product on hanger bolts and fix the

nuts tightly. (Fig.10)

4.Install the ducts. (It is same with step 4 in P.7)

5.Set an square

inspection hole of

450 mm or more

beside and below the

maintenance board.

(Fig.11)

Please use the spirit level to adjust the body, to

ensure that the height of the three spreaders

within ± 2 mm.

Note

Fig.8

Unit : inch (mm)

3-Hanger

bolts

Nut

Washer

Nut

Fig.9

Fig.10

Fig.11

8 7/8 (224)

1/2 (12)

2 1/2 (65)

3 (78)

Square inspection holeCeiling

17 3/4 (450)

Square inspection holeCeiling

17 3/4 (450)

1/2 (12)

1 (25)

Ceiling

Hanger

Insert power cord plug into

power socket, then open

the control box cover and turn

on the main switch. (Fig.12)

Control panel

Air volume dial switch

Main switch

Port receptacle for add-on Module provides additional

features. (Module sold separately)

For details, please consult Panasonic Call Center

Telephone : 1-866-292-7299 (USA)

1-800-669-5165 (Canada)

”I” is on

“O” is off

Control box cover

Filter indicator

Running indicator

Filter reset button

Default setting : 80 CFM

OPERATION

Humidity dial switch

Default setting : 80 %RH

If the product inside humidity detected by sensor is over than setting value, the fan will

stop for 60 minutes, then according to the detected value to determine whether to

operate.

If the switch is turned to OFF position, the humidity sensor detection function will be

disabled.

Press the button after filter maintenance for resetting accumulated running time and the

filter indicator will light off, the buzzer will turn off.

Adjusting the product air volume by this dial switch, you can choose 50, 60, 70,

80, 90, 100, 110, 130, 150 CFM.

Adjusting the humidity protection value of the product by this dial switch, you can choose

from 30 %RH~80 %RH (stepless) or turned to OFF position.

When the indicator is on green, indicates the product is running.

The indicator will light on red when the accumulated running

time is up to 90 days. When the indicator is on (with buzzer

sound), indicates need to maintain filters.

(1)The indicator will be on when the product accumulated

running time reaches to 90 days. The buzzer will sound

every hour and 10 seconds in an hour.

(2)If you want to turn off the indication of buzzer, please

press filter reset button about 3 seconds until there is the

sound of a long beep. Press filter reset button about 3

seconds again until there is sound of two quick beeps, the

buzzer indication will be turned on again.

(3)If you want to cancel buzzer sound when sleeping, you

just need to turn off the wall switch. The buzzer will

continue to sound when the product is turned back on and

will not stop until the filter has been maintained and the

filter alarm has been reset.

(4)When the the running indicator or filter indicator blinks, means

the product failure.

Note

Fig.12

Temperature dial switch

Default setting : 15 °F

If the product inside temperature detected by sensor is lower than setting value, the fan

will stop for 60 minutes, then according to the detected value to determine whether to

operate.

If the product inside temperature detected by sensor is higher than 95 °F (35 °C), the fan

will stop for 60 minutes, then according to the detected value to determine whether to

operate.

If the switch is turned to OFF position , the temperature sensor detection function will

be disabled.

Adjusting the temperature protection value of the product by this dial switch, you can

choose 15 °F~40 °F (stepless) or turned to OFF position.

MAINTENANCE

OPERATION

To avoid injury or electric shock, turn off the main switch in control box to stop the fan

before checking, cleaning or replacing filter.

To ensure product running normally, routine maintenance must be performed every

3 months.

Please wear gloves to avoid pinching fingers during maintenance.

When cleaning or replacing filters, dust, insects, etc. attached on the filters may fall.

Please pay attention to the protection of eyes and so on.

CAUTION

The humidity and temperature value detected by sensor may be different from outside.

Note

Turn off main switch. (Fig.13)

Twist hand screw open maintenance board.

(Fig.13)

Open the control box cover by twist hand

screw. (Fig.13)

2.Pull out the pre-filter, clean it with water once in

3 months when filter indicator lights on with

buzzer sound “Pi-Pi-Pi-...”. (Fig.14)

Pre-filter

Fig.13

Fig.14

Andere Handbücher für FV-15NLFS1

Inhaltsverzeichnis

Andere Panasonic Lüfter Handbücher

Panasonic

Panasonic WhisperGreen FV-08VKML3 Bedienungsanleitung

Panasonic

Panasonic F-56PZM Bedienungsanleitung

Panasonic

Panasonic FV-1115VQ1 Bedienungsanleitung

Panasonic

Panasonic Whisper Green-Lite FV-08VKL1 Bedienungsanleitung

Panasonic

Panasonic FV-05-11VKL1 Bedienungsanleitung

Panasonic

Panasonic WhisperCeiling FV-20VQ3 Bedienungsanleitung

Panasonic

Panasonic FV-05VS1 Bedienungsanleitung

Panasonic

Panasonic FV-0510VS1 Bedienungsanleitung

Panasonic

Panasonic F-128T Bedienungsanleitung

Panasonic

Panasonic Whisper Value-Lite FV-10VSL2 Bedienungsanleitung

Panasonic

Panasonic FV-0510VSC1 Bedienungsanleitung

Panasonic

Panasonic FV-15ZY1 Bedienungsanleitung

Panasonic

Panasonic Whisper Fit-Lite FV-05VFL3 Bedienungsanleitung

Panasonic

Panasonic WhisperSense FV-08VQCL6 Bedienungsanleitung

Panasonic

Panasonic FV-30BY1 Bedienungsanleitung

Panasonic

Panasonic FV-08VKME3 Bedienungsanleitung

Panasonic

Panasonic F-48MZ2 Bedienungsanleitung

Panasonic

Panasonic FV-11VH1 Bedienungsanleitung

Panasonic

Panasonic RG-T810A Bedienungsanleitung

Panasonic

Panasonic FV-05-11VKSL1 Bedienungsanleitung

Panasonic

Panasonic Whisper Green FV-08VKM1 Kurzanleitung

Panasonic

Panasonic Whisper-Lite FV-08VQL4 Bedienungsanleitung

Panasonic

Panasonic F-M12GX Bedienungsanleitung

Panasonic

Panasonic FV-15NLFS1 Bedienungsanleitung

Beliebte Lüfter Handbücher anderer Marken

ELTA FANS

ELTA FANS H03VV-F Bedienungsanleitung

Hunter

Hunter 20714 Gebrauchsanweisung

Emerson

Emerson CARRERA VERANDA CF542ORB00 Bedienungsanleitung

Hunter

Hunter Caraway Gebrauchsanweisung

Kompernass

Kompernass KH 1150 Bedienungsanleitung

VES

VES FALA100/12V/TR Bedienungsanleitung

Vertiv

Vertiv Liebert DCD Bedienungsanleitung

Westinghouse

Westinghouse GFP Series Bedienungsanleitung

Venmar

Venmar KUBIX HRV PLUS Series Bedienungsanleitung

Maico

Maico ECR 31 Bedienungsanleitung

Sonnenkonig

Sonnenkonig Dinky Bedienungsanleitung

S&P

S&P ECOWATT HXBR Bedienungsanleitung

Wider

Wider IMP03369BH Bedienungsanleitung

Hinkley

Hinkley HIGHLAND Bedienungsanleitung

Broan

Broan 766BN Bedienungsanleitung

Premium

Premium PFS16022 Montageanleitung

Litex Industries

Litex Industries E-CGL52CB5C1 Bedienungsanleitung

Lindab

Lindab LTDF Bedienungsanleitung