Panasonic EH-NE83 Bedienungsanleitung

Order Number PEWT1710A28CE

(Household) Hair Dryer

Model No.

EH-NE83

Asia

Middle East

TABLE OF CONTENTS PAGE

1 Warning ---------------------------------------------------------------------------------------

2 Specifications ------------------------------------------------------------------------------- 2

3 Troubleshooting Guide ------------------------------------------------------------------------ 3

4 Disassembly and Assembly Instructions -------------------------------------------- 5

5 Wiring Connection Diagram------------------------------------------------------ 12

6 Schematic Diagram ---------------------------------------------------------------- 15

7 Exploded View & Replacement Parts List ----------------------------------- 16

and distribution is a violation of law.

1. Warning

Caution:

- Pb free solder has a higher melting point that standard solder; Typical the melting point is 50 - 70°F (30 - 40℃) higher.

Please use soldering iron with temperature control and adjust it to 750 ±20°F (400 ± 10 ℃).

In case of using high temperature soldering iron, please becareful not to heat too long.

- Pb free solder will tend to splash when heated too high (about 1100°F / 600℃).

Power source

Power consumption

(" II - Hot ")

Air volume without nozzle

Air temperature without nozzle

(" II - Hot ")

Dimensions

Cord length

Weight

Supplied accessory

90 K (in case of room temperature 30°C)

(W) 90mm x (D) 220mm. x (H) 270mm.

(without power cord and nozzle)

2. Specifications

AC 220-240 V , 50~60 Hz

Code L / 605 / 615 / 655 / 685 = 1.7 m

Approx. =530g.

Set nozzle

AC 220 V, 50~60 Hz, 2100 W

AC 230 V, 50~60 Hz, 2300 W

AC 240 V, 50~60 Hz, 2500 W

1.9 m3/min

3. TROUBLESHOOTING GUIDE

Refer to WIRING CONNECTION DIAGRAM.

< TROUBLE >

< CHECK >

< REMEDY >

Check if there are odd objects between

joints of thermo switch or not

(Figure 3)

Remove the odd objects

between joints

Found odd object

No odd objects

Replace the

MOTOR HEATER ASSEMBLY

Figure 3

Thermo Switch

Hot air is not emitted

Check the conductivity between the terminal 1

and 2 by push and hold

the COOL SWITCH BUTTON

(Figure 2)

Check the conductivity between the terminal 2

and 4 by setting

the TEMPERATURE SWITCH to Position 2

(Figure 1)

Replace the

MAIN SWITCH

Replace the

COOL SWITCH BUTTON

Lead Wire (Orange)

Lead Wire (Blue and Red)

For EH-NE81-84 only

Figure 2

Figure 1

Lead Wire (Black)

Lead Wire (Brown)

Lead Wire (Orange)

Temperature Switch

3. TROUBLESHOOTING GUIDE

Refer to WIRING CONNECTION DIAGRAM.

< TROUBLE >

< CHECK >

< REMEDY >

Main body is

not operated

Check the conductivity of power cord

Check the conductivity between the terminal 1

and 4 by setting

the MAIN SWITCH to Position 1

(Figure 4)

Replace the

MAIN SWITCH

Replace the

MOTOR HEATER

ASSEMBLY

Replace the

MOTOR HEATER

ASSEMBLY

Lead Wire (Yellow)

Lead Wire (Red)

Lead Wire (Gray)

Lead Wire (Orange)

*For code : 605, 655, 685, 695, 865

MAIN SWITCH

Figure 4

4. Disassembly and Assembly Instructions

4.1. Disassembly Instructions

1. Remove the FILTER FRAME ASSEMBLY 4. Remove TAPPING SCREWS by a cross

slot screw driver.Than take out AIR OUTLET RING

and AIR OUTLET GRILL by rotating follow the direction

below.

2. Remove 3 TAPPING SCREWS by a cross

slot screw driver,then Remove AIR INLET RING.

5. Take off HOUSING AB follow the figure below.

3. Remove 2 TAPPING SCREWS at HOUSING A

by flat-blade screwdriver and 2 TORX SCREWS

at HANDLE by Driver then remove HANDLE AB.

6. Remove DISCHARGE COVER

Counter clockwise rotation

4. Disassembly and Assembly Instructions

4.1. Disassembly Instructions

7. remove Ion Holder from DISCHARGE COVER as figure below.

8. Take off MOTOR HEATER ASSEMBLY, and PLATE SPRING from HOUSING B.

Unclip this 2 ribs

4.2 Assembly Instructions

1. High voltage lead wire for Ion discharge must be fixing with Ribs from Heater holder as below picture.

2. Install MAIN SWITCH PLATE AB and MAIN SWITCH HOLDER.

3. Install Ion discharge in to DISCHARGE COVER.

Ribs of MAIN SWITCH

HOLDER must fully

lock with MAIN SWITCH

(2 Ribs)

4. Assemble MOTOR HEATER ASSEMBLY, COOL SWITCH PLATE and PLATE SRPING into HOUSING B.

Lead wire to Heater block

assembly

must not on this area

Position of component must be as below

(EH-NE81,82,83,84 only)

5. Assemble DISCHARGE COVER / DESIGN COVER into HOUSING B.

6. Assemble HOUSING A, then tightening 2 TORX SCREWS.

7. Assemble AIR INLET RING and 3 TAPPING SCREWS.

TAPPING SCREWS 2.6*10

TORX SCREWS 3.0*12

Inhaltsverzeichnis

Andere Panasonic Haartrockner Handbücher

Panasonic

Panasonic EH-NE65-K655 Bedienungsanleitung

Panasonic

Panasonic EH-ND61 Bedienungsanleitung

Panasonic

Panasonic EH-NE70 Bedienungsanleitung

Panasonic

Panasonic EH?NA65 Bedienungsanleitung

Panasonic

Panasonic nanoe EH-NA46 Bedienungsanleitung

Panasonic

Panasonic nanoe EH-NA67 Bedienungsanleitung

Panasonic

Panasonic EH-ND63 Bedienungsanleitung

Panasonic

Panasonic EH-NE44 Bedienungsanleitung

Panasonic

Panasonic nanoe EH-NA65CN765 Bedienungsanleitung

Panasonic

Panasonic EH-ND43 Bedienungsanleitung

Panasonic

Panasonic EH-NE20 Bedienungsanleitung

Panasonic

Panasonic EH-ND33 Bedienungsanleitung

Panasonic

Panasonic EH-NE86 Bedienungsanleitung

Panasonic

Panasonic EH-ND57 Bedienungsanleitung

Panasonic

Panasonic nanoe EH-NA27 Bedienungsanleitung

Panasonic

Panasonic EH-ND52 Bedienungsanleitung

Panasonic

Panasonic EH-NE64 Bedienungsanleitung

Panasonic

Panasonic EH-NA45 Bedienungsanleitung

Panasonic

Panasonic EH-NE42 Bedienungsanleitung

Panasonic

Panasonic EH-NE32 Bedienungsanleitung

Panasonic

Panasonic EH-NE27 Bedienungsanleitung

Panasonic

Panasonic EH-ND21 Bedienungsanleitung

Panasonic

Panasonic EH?NA65 Bedienungsanleitung

Panasonic

Panasonic nanoe EH-NA55 Bedienungsanleitung

Beliebte Haartrockner Handbücher anderer Marken

CTC Union

CTC Union Clatronic HT 3428 Bedienungsanleitung

Rowenta

Rowenta Motion Dry Ionic CV3721K0 Bedienungsanleitung

Bosch

Bosch PHD5962 Bedienungsanleitung

Conair

Conair Infiniti 213 Benutzerhandbuch

Beurer

Beurer Elle HDE 15 Bedienungsanleitung

Braun

Braun 3542 Bedienungsanleitung

Marta

Marta MT-1498 Bedienungsanleitung

AEG

AEG FOEN HT 5608 Bedienungsanleitung

Vitek

Vitek VT-2378 Bedienungsanleitung

ARESA

ARESA AR-3215 Bedienungsanleitung

TREVIDEA

TREVIDEA SPASSO G3 FERRARI G30029 Bedienungsanleitung

Helvex

Helvex MB-1011 Bedienungsanleitung

Dolphin

Dolphin BC109-ST5 Valera+ Bedienungsanleitung

Remington

Remington Get The Look D3110GP Bedienungsanleitung

Conair

Conair VS Sassoon Eco Dry Bedienungsanleitung

Dyson

Dyson supersonic HD01 Bedienungsanleitung

Grundig

Grundig HD 2509 R Bedienungsanleitung

Imetec

Imetec Bellissima My Pro Diffon DF1 3000 Bedienungsanleitung