Panasonic EY7270-X8 Bedienungsanleitung

1 SCHEMATIC DIAGRAM 2

2 WIRING CONNECTION DIAGRAM 2

3 DISASSEMBLY/ASSEMBLY INSTRUCTIONS 3

reserved. Unauthorized copying and distribution is a

violation of law.

EY7270-X8

EY7271-X8

4 TROUBLESHOOTING GUIDE 7

5 CHECK PARTS IDENTIFY PROCEDURE 9

6 EXPLODED VIEW & REPLACEMENT PARTS LIST 10

Cordless Impact Driver

SPECIFICATIONS

CONTENTS

Page Page

ORDER NO. PTD0606X34CE

1 SCHEMATIC DIAGRAM

2 WIRING CONNECTION DIAGRAM

EY7270-X8 / EY7271-X8

3 DISASSEMBLY/ASSEMBLY INSTRUCTIONS

Ref. No. 1A Procedure 1A Removal and attachment of the Housings.

1. Loosen the belt hook bolt turning it counterclockwise, using a

coin or a flat blade screwdriver.

2. Take out the belt hook.

3. Remove nine housing screws.

4. Open the housing B.

NOTE :

The housing A and B is tightened as the motor mounting base

is joint fitting.

Hold the housing B and take it out vertically.

5. Take out the fixation cover, protectors and anvil block.

(Removal)

NOTE :

When opening the housings, make sure that the main PCB is

on the housing A.

If the main PCB sticks in the housing B and pull it out from the

housing A, the ribbon cable may be defected.

(Attachment)

1. Insert the click spring into the housing A.

NOTE :

Be sure to use the tweezers or the small flat-head screwdriver

when inserting the click spring.

EY7270-X8 / EY7271-X8

Ref. No. 1B Procedure 1A →

→→

→1B Removal and attachment of the Motor.

(Removal)

1. Take out the motor with the driving block from housing.

2. Separate the motor assembly from the driving block.

3. Take out the motor rotor assembly from the motor stator.

NOTE :

Make sure not to damage the magnet by motor rotor.

(Attachment)

1. Insert the motor rotor assembly into the stator with care of hitching

FET.

NOTE :

Make sure that there is no metal powder around the motor rotor.

Ref. No. 1C Procedure 1A →

→→

→1B →

→→

→1C Removal of the Driving Block.

1. Remove the thrust plate.

2. Take out the planet gears and pins slightly tapping the driving block

on the table.

EY7270-X8 / EY7271-X8

Ref. No. 1D Procedure 1A →

→→

→1B →

→→

→1C→

→→

→1D Removal and attachment of the Switch.

1. Take out the switch assembly from the housing.

(Attachment)

1. Connect the motor lead wires.

NOTE :

Do not push the area where marked the arrow in order to

prevent the breakage.

2. Insert the connectors into the FET, the main PCB and the motor

stator.

NOTE :

Make sure to handle the ribbon cable gently in order to avoid the

breakage.

Apply the grease (FLOIL) on the places where insert into the

connectors.

EY7270-X8 / EY7271-X8

Ref. No. 1E Procedure 1A →

→→

→1B →

→→

→1C→

→→

→1D→

→→

→1E Assembly of the Driving Block.

1. Press fit the lead wires firmly.

2. Place the ribbon cable properly without getting caught in the lead

wires.

EY7270-X8 / EY7271-X8

(Refer to WIRING CONNECTION DIAGRAM)

4 TROUBLESHOOTING GUIDE

< TROUBLE > < CHECK > < REMEDY >

Does not operate. <CHECK BATTERY PACK.> NO Replace battery pack.

→If no less than 12V DC is available across the (+) and (-) terminals, →

the battery pack is OK.

NOTE: The battery pack is sold separately as an optional accessory.

See the nearest sales dealer for details. The battery pack has a

limited life.

The pack should be replaced if

-after being charged for the rated charging time the battery voltage

is less than 12V DC or the usable time is extremely short.

-the battery leaks. Check battery for leaks and terminals for

corrosion.

↓OK

<CHECK TERMINAL CONNECTIONS BETWEEN MAIN UNIT NO Repair contacts.

AND BATTERY PACK.> →

Check for proper terminal contacts.

↓OK

<CHECK MOTOR ROTOR.> NO Replace motor

Check the condition of rotor if there is any wear, crack and deformation. →rotor assembly.

↓OK

<CHECK MOTOR STATOR.> NO Replace motor

Check the condition of motor case if there is any crack and deformation. →stator.

Does not speed- <CHECK SWITCH.> NO Replace switch

control. →See in detail at CHECK PARTS IDENTIFY PROCEDURE. →assembly.

Does not light LED.

Does not change

impact mode.

EY7270-X8 / EY7271-X8

< TROUBLE > < CHECK > < REMEDY >

Does not vibrate <CHECK ANVIL.> NO Replace anvil.

or weakness of →Check wear condition of anvil. If no less than 1mm from →

vibration. the corner at (A) side or 0.5mm from the corner at (B) side,

anvil is OK.

↓OK

<CHECK HAMMER.> NO Replace hammer.

Check wear condition of hammer. If no less than 2mm from the corner →

at (C) side or 1mm from the corner at (D) side, hammer is OK.

EY7270-X8 / EY7271-X8

5 CHECK PARTS IDENTIFY PROCEDURE

EY7270-X8 / EY7271-X8

6 EXPLODED VIEW & REPLACEMENT PARTS LIST

6.1. EY7270 EXPLODED VIEW

EY7270-X8 / EY7271-X8

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Panasonic Impact Driver Handbücher

Panasonic

Panasonic EY75A1 Bedienungsanleitung

Panasonic

Panasonic EY75A7X57 Bedienungsanleitung

Panasonic

Panasonic EY7206 - 12V IMPACT DRIVER Bedienungsanleitung

Panasonic

Panasonic EY7271 Bedienungsanleitung

Panasonic

Panasonic EY7206GQW Bedienungsanleitung

Panasonic

Panasonic EY6588 Bedienungsanleitung

Panasonic

Panasonic EY7530 Bedienungsanleitung

Panasonic

Panasonic EY7201-X8 Bedienungsanleitung

Panasonic

Panasonic EY75A1 Bedienungsanleitung

Panasonic

Panasonic EY75A7 Bedienungsanleitung

Panasonic

Panasonic EY75A7 Bedienungsanleitung

Panasonic

Panasonic EY7202-U1 Bedienungsanleitung

Panasonic

Panasonic EY75A1 Bedienungsanleitung

Panasonic

Panasonic EY7541 - CORDLESS IMPACT WRENCH Bedienungsanleitung

Panasonic

Panasonic EYFLA3J - DRILL - MULTI LANGUAGE Bedienungsanleitung

Panasonic

Panasonic EY7206 - 12V IMPACT DRIVER Bedienungsanleitung

Panasonic

Panasonic EY7542 - CORDLESS IMPACT WRENCH Bedienungsanleitung

Panasonic

Panasonic EYFLB1A Bedienungsanleitung

Panasonic

Panasonic EY7541 - CORDLESS IMPACT WRENCH Bedienungsanleitung

Panasonic

Panasonic EYFLF1XC Bedienungsanleitung

Panasonic

Panasonic EYFLA6PR Bedienungsanleitung

Panasonic

Panasonic EY7430 Bedienungsanleitung

Panasonic

Panasonic EYFPA1J Bedienungsanleitung

Panasonic

Panasonic EY75A7 Bedienungsanleitung

Beliebte Impact Driver Handbücher anderer Marken

stayer

stayer IW500D Bedienungsanleitung

Makita

Makita DTD152 Bedienungsanleitung

Milwaukee

Milwaukee M12 FID Bedienungsanleitung

Grizzly

Grizzly H6140 Bedienungsanleitung

Makita

Makita BTW450 Bedienungsanleitung

Ozito

Ozito LID-3000 Bedienungsanleitung

Astro Pneumatic Tool

Astro Pneumatic Tool 1812 Bedienungsanleitung

Greenlee

Greenlee HW3 Bedienungsanleitung

Sthor

Sthor 57091 Bedienungsanleitung

Makita

Makita DTD145 Bedienungsanleitung

Hilti

Hilti SIW 2-A12 Bedienungsanleitung

Ryobi

Ryobi R18IW3 Bedienungsanleitung

Parkside

Parkside PDSSA 20-Li A1 Bedienungsanleitung

Flex

Flex FX1471 Bedienungsanleitung

SATA

SATA 51075C Technisches Handbuch

Cembre

Cembre NR-11P Bedienungsanleitung

Makita

Makita BTP131RFE Bedienungsanleitung

DeWalt

DeWalt XR Li-ion DCF902 Bedienungsanleitung