Panasonic KX-HDV230C Bedienungsanleitung

Home

PBXware

SERVERware

TELCOware

SIPmon

SIPProt

Desktop & Mobile

BRM

UADs

Appliances

EOL

From Bicom Systems Wiki

Contents

1 Introduction

■

2 Requirements

■

2.1 Identifying Phone Model

■

2.2 Phone Firmware

■

2.3 DHCP Server

■

2.4 PBXware Version

■

3 Installation

■

3.1 Power Adapter

■

3.2 Power over Ethernet (PoE)

■

3.3 Find the Phone's IP Address

■

3.4 Reset to Factory Settings

■

4 Registering Phone

■

4.1 Manual Configuration

■

4.2 Auto Provisioning

■

Introduction

This Configuration Guide is written as a general guide on how to configure the Panasonic phone

model KX-HDV230C to work with PBXware 5.3.8.

Requirements

Identifying Phone Model

To start and successfully complete the registration of your Panasonic phone, you need to know

which phone model to set up.

On the back of each Panasonic phone, there is model information that you should check.

Although various phone models can have exactly the same requirements and installation

procedures, phone models can also have significantly different requirements and installation

procedures, so that is why it is important to know the model you own which results in you

setting up the phone successfully.

Phone Firmware

Make sure that the phone is loaded with an appropriate firmware version, HDV230/11.180.

■

To find out the firmware version of the Panasonic phone model, open a new browser window

■

and enter the phone's IP address in order to access the phone's web administration interface

NOTE: The phone's web administration web interface is disabled by default. To enable

access, go to Settings --> Network Settings and enable the Embedded Web option.

■

note that the factory default login details are as follows: username is admin and password is

adminpass.

DHCP Server

Fully configured and operational DHCP server.

PBXware Version

PBXware Version 5.3.8

In order to find out the PBXware version:

■

Navigate to Settings: About.

■

On the top of the About page is a code similar to this one Edition: Multi-Tenant, Release:

5.3.8.0 (2223ce45), Running: 13.23.1-gc-040bbaca, Proxy v5.3.8 (231c5f3), API: 5.3,

libmemcached version: 1.0.18, where 'Release' denotes the exact version of PBXware.

Installation

This section describes how to install and connect the phone to the electrical power and data

network as well as how to apply factory settings.

The following topics are covered:

Power Adapter

■

Power Over Ethernet (PoE)

■

Factory Settings

■

Power Adapter

Connect the Network and Power

Connect the DC plug on the power adapter to the DC port on the phone and connect the other

■

end of the power adapter into an electrical power outlet.

Connect the Ethernet cable between the Internet port on the phone and the network port on a

■

router or switch to access LAN.

NOTE: If you are using Power over Ethernet (PoE), you do not need to connect the AC adapter.

Make sure the Ethernet cable and router or switch is Power over Ethernet (PoE) compliant.

Power over Ethernet (PoE)

Connect the Network (only)

Using a regular ethernet cable, your phone can be powered from a Power over Ethernet (PoE)

compliant router or switch.

Connect the Ethernet cable between the Internet port on the phone and an available port on

■

the in-line power router or switch.

NOTE: If you are using Power over Ethernet (PoE), you don't need to connect the AC adapter.

Please make sure that the Ethernet cable and router or switch is Power over Ethernet (PoE)

compliant.

Find the Phone's IP Address

Find out your Panasonic phone IP Address.

Press the Status tab.

■

Press Network Status.

■

The IP address will be displayed on the display.

Reset to Factory Settings

This step is not required for brand new out-of-the-box phones, however, if the phone has been

already used then it is a must.

Open a new browser window and enter the phone's IP address in order to access the phone's

■

web administration interface login screen. Example: http://192.168.1.22.

■

note that the factory default login details are as follows: username is admin and password is

adminpass.

Click the Maintenance tab.

■

Click the Reset to Defaults section in the left navigation menu.

■

Click the Reset to Carrier Defaults button in order to factory reset the phone.

■

Wait some time for the phone to reboot.

■

NOTE: Do not unplug or remove power to the phone while it is updating firmware and

configuration.

Registering Phone

This section describes how to identify the Panasonic phone model, requirements that must be

met and how to register the phone using manual configuration or auto provisioning.

The following topics are covered:

Manual Configuration

■

Auto Provisioning

■

Manual Configuration

This section describes how to set UAD settings, create a PBXware Extension, and register the

phone.

The following topics are covered:

UAD Settings

■

Creating an Extension

■

Registering a Phone

■

UAD Settings

UAD settings

Open a new browser window and enter the IP address in order to access the PBXware's web

■

administration login screen. Example: http://192.168.1.10.

■

UAD Settings

Navigate to Settings:UAD.

■

Make sure Panasonic UAD is enabled. To check the UAD status, click the Edit icon

■

corresponding to the Panasonic phone.

Make sure Status is set to Active, Auto provisioning is set to No, and DHCP is set to Yes.

■

Click the Save button to save changes.

■

Creating an Extension

Creating Extension

Add an Extension

Navigate to Extensions. Click Add Extension.

■

The standard options window will be shown below.

■

Select the Panasonic phone model from the UAD select box.

■

Select Location: Local or Remote.

■

Local is for all Extensions registered on the LAN and Remote is for all Extensions

registered from remote networks, WAN, Internet etc.

Click the Next step button.

■

Extension Values

Enter values into the required field text boxes.

REQUIRED FIELDS:

Name

■

Enter a name for the Extension being created. Example: John Smith.

E-mail

■

Enter the e-mail address associated with this Extension. This e-mail address will receive

all system notification messages. Example: [email protected]

Department

■

Department to which this Extension belongs. Example: Sales.

Click the Save button.

■

Registering a Phone

This section describes how to register a Panasonic phone using Hostname or IP Address.

Hostname or IP Address

Open a new browser window and enter the phone's IP address in order to access the phone's

■

web administration interface login screen. Example: http://192.168.1.22

■

note that the factory default login details are as follows: username is admin and password is

adminpass.

Click VoIP in the navigation tab.

■

Click Line 1 in the left navigation tab, section SIP Settings.

■

Enter or set the following details into the respective fields.

■

REQUIRED FIELDS:

Phone Number

■

Usually the same number as the Authentication ID.

Registrar Server Address

■

Enter the Hostname or IP Address of the PBXware.

- Example of a Hostname: voip.bicomsystems.com

- Example of an IP Address: 192.168.1.10

Proxy Server Address

■

Same as the Registrar Server Address.

Authentication ID

■

PBXware Extension number. Example: 1003

Authentication Password

■

The Secret of the Extension as received in the e-mail associated with this Extension.

Example: _%Z4M3*Ts9y7. A password is generated automatically for each newly created

Extension.

Click the Save button.

■

If everything is done as described above, you should have successfully registered your phone

■

to PBXware.

Dial *123 to verify the registration.

Auto Provisioning

This section describes how to set UAD settings, create PBXware Extension and register the

phone using DHCP or Static IP address.

The following topics are covered:

UAD Settings

■

Creating an Extension

■

Registering a Phone

■

UAD Settings

UAD settings

Open a new browser window and enter the IP address in order to access the PBXware's web

■

administration login screen. Example: http://192.168.1.10.

■

UAD Settings

Navigate to Settings: UAD.

■

Make sure Panasonic UAD is enabled. To check the UAD status, click the Edit icon

■

corresponding to the Panasonic phone.

Make sure Status is set to Active, Auto provisioning is set to Yes, and DHCP is set to Yes.

■

Click the Save button to save changes.

■

Creating an Extension

Creating Extension

Add an Extension

Navigate to Extensions. Click Add Extension.

■

The standard options window will be shown below.

■

Select a Panasonic phone model from the UAD select box.

■

Select Location: Local or Remote.

■

Local is for all Extensions registered on the LAN and Remote is for all Extensions

registered from remote networks, WAN, Internet etc.

Click the Next step button.

■

Extension Values

Enter values into the required field text boxes.

REQUIRED FIELDS:

Name

■

Enter a name for the Extension being created. Example: John Smith.

E-mail

■

Enter the e-mail address associated with this Extension. This e-mail address will receive

all system notification messages. Example: [email protected]

Auto Provisioning

■

Set to Yes.

MAC Address

■

Enter the Panasonic phone's MAC address. Example: bcc342123456. The MAC address

can be found at the back of the phone.

Click the Save button.

■

Registering a Phone

This section describes how to register a Panasonic phone using DHCP, TFTP or HTTP.

The following topics are covered:

DHCP

■

TFTP or HTTP

■

DHCP

Configure DHCP

Make sure your DHCP router is configured to use option 66 to automatically instruct phones

■

with the URL for auto provisioning. For more information, refer to the router documentation

or contact your network administrator.

Phone's first boot or user-initiated reboot

The auto provisioning process will start during the phone's first boot or after the reboot

■

process has been initiated by the user. The DHCP server will instruct the phone from where to

pickup an appropriate configuration file. If everything is done as described above, you should

have successfully registered your phone to PBXware.

Dial *123 to verify registration.

TFTP or HTTP

Open a new browser window and enter your phone IP address, e.g. http://192.168.1.22.

■

Enter username and password and press the Confirm button. NOTE: The factory default

■

Click the Maintenance tab.

■

Click the Provisioning Maintenance link in the left navigation menu.

■

Choose what server type you intend to use: HTTP or Trivial FTP. NOTE: Our

■

recommendation is to use HTTP.

If you choose to use server type HTTP, enter http:// followed by Hostname or IP

Address, followed then by /prov in Standard File URL.

Example of a Hostname using HTTP:

http://username:[email protected]/prov/{mac}.cfg

Example of an IP Address using HTTP:

http://username:[email protected]/prov/{mac}.cfg

Enter the Auto Provisioning username and password into the Authentication ID and

■

Authentication Password fields.

If you choose to use server type TFTP, enter tftp:// followed by Hostname or IP

Address

Example of a Hostname: tftp://192.168.1.136/{mac}.cfg

Example of a IP Address: tftp://192.168.1.136/{mac}.cfg

Click the Save button.

■

You will have to wait a couple of seconds for the configuration to be updated. NOTE: Do not

■

power off your phone.

If everything is done as described above, you should have successfully registered your phone

■

to PBXware.

Dial *123 to verify registration.

Retrieved from "http://wiki.bicomsystems.com/Panasonic_KX-HDV230C"

Disclaimers - About Bicom Systems Wiki

Inhaltsverzeichnis

Andere Panasonic IP-Telefon Handbücher

Panasonic

Panasonic T-Mobile KX-HDV130 Service-Handbuch

Panasonic

Panasonic KX-UT136-B Bedienungsanleitung

Panasonic

Panasonic BBGT1500 - GLOBARANGE CORDLESS PHONE Bedienungsanleitung

Panasonic

Panasonic KX-UDT 111 Bedienungsanleitung

Panasonic

Panasonic JOIP BB-GT1540E Bedienungsanleitung

Panasonic

Panasonic KX-UT113 Bedienungsanleitung

Panasonic

Panasonic KX-NT321 Bedienungsanleitung

Panasonic

Panasonic KX-TDA30 Bedienungsanleitung

Panasonic

Panasonic KX-NT265 Bedienungsanleitung

Panasonic

Panasonic KX-DT521 Bedienungsanleitung

Panasonic

Panasonic KX-UTG200 Bedienungsanleitung

Panasonic

Panasonic KX-UTG200 Bedienungsanleitung

Panasonic

Panasonic KX-UT123 Bedienungsanleitung

Panasonic

Panasonic JOIP BB-GT1540SP Einrichtungshandbuch

Panasonic

Panasonic KX-TD208E Technische Daten

Panasonic

Panasonic KX-TGP500 Gebrauchsanweisung

Panasonic

Panasonic KX-NT343 Bedienungsanleitung

Panasonic

Panasonic KX-TGA301C Bedienungsanleitung

Panasonic

Panasonic KX-UT248 Bedienungsanleitung

Panasonic

Panasonic KX-UT113 Bedienungsanleitung

Panasonic

Panasonic TGP600 Bedienungsanleitung

Panasonic

Panasonic KX-TGP600 Service-Handbuch

Panasonic

Panasonic KXDT346 - DIGITAL PROPRIETARY TELEPHONE Bedienungsanleitung

Panasonic

Panasonic KX-TCA120EX Bedienungsanleitung

Beliebte IP-Telefon Handbücher anderer Marken

Alcatel

Alcatel 4028 Bedienungsanleitung

Polycom

Polycom Polycom VVX 600 Bedienungsanleitung

Polycom

Polycom SoundPoint IP 450 Bedienungsanleitung

Cisco

Cisco SPA-500 Series Bedienungsanleitung

Polycom

Polycom SoundPoint IP 650 Bedienungsanleitung

Proximus

Proximus Maestro 3016 IP Bedienungsanleitung

Fanvil

Fanvil X4 Bedienungsanleitung

Cisco

Cisco 7962 Bedienungsanleitung

Snom

Snom 320 Bedienungsanleitung

Yealink

Yealink Yealink SIP-T46G Bedienungsanleitung

Avaya

Avaya 4625SW Bedienungsanleitung

Yealink

Yealink SIP-T52S Bedienungsanleitung

Nortel

Nortel 1140E Bedienungsanleitung

Nexotek

Nexotek NT-P500 Bedienungsanleitung

Avaya

Avaya Integral 5 R3.0 Bedienungsanleitung

GE 28320EE2 - Dect 6.0 InfoLink 2 Bedienungsanleitung

Avaya

Avaya 4600 Series Service-Handbuch

Mitel

Mitel MIVOICE OFFICE 400 6940 SIP Bedienungsanleitung