Panasonic BY-HPE11KTCE Bedienungsanleitung

Operating Instructions

Coaxial - LAN Converter with PoE function

Indoor Use Only

Model No. BY-HPE11KTCE

BY-HPE11R

BY-HPE11H

Attached Installation Guide

Before attempting to connect or operate this product, please read these instructions carefully and

save this manual for future use.

Introduction

About the user manuals

• There are 2 sets of operating instructions for this unit as follows.

– Installation Guide: Explains how to install and connect devices.

– Operating Instructions (PDF): Explains how to perform the settings and how to

operate this unit.

Adobe® Reader® is required to read these operating instructions (PDF) on the

provided CD-ROM. When the Adobe Reader is not installed on the PC, download

the latest Adobe Reader from the Adobe web site and install it.

• The BY-HPE11R adaptor is called the camera adaptor and the BY-HPE11H adaptor

is called the center adaptor in this document.

Trademarks

• Microsoft, Windows, Windows Vista, and Internet Explorer are either registered

trademarks or trademarks of Microsoft Corporation in the United States and/or other

countries.

• Microsoft product screen shot(s) reprinted with permission from Microsoft

Corporation.

• Linux is a registered trademark of Linus Torvalds in the United States, other

countries, or both.

• Adobe and Reader are either registered trademarks or trademarks of Adobe

Systems Incorporated in the United States and/or other countries.

• All other trademarks identified herein are the property of their respective owners.

2 Operating Instructions

Introduction

For Your Safety

To prevent severe injury and loss of life/property, read this section carefully before using

the unit to ensure proper and safe operation of your unit.

WARNING

Consult an authorized dealer for mounting

• Experience and knowledge are required to perform mounting of the unit. Incorrect

mounting can cause damage to the unit, fire, electric shock, or injury. Make sure

to consult an authorized dealer for mounting.

Do not damage the AC cord or power plug

• Do not allow the AC cord or plug to be damaged, placed near heat emitting

devices, excessively pulled, bent or placed under heavy objects. Using damaged

AC cords or plugs can result in the risk of fire or electric shock. Contact an

authorized service center for AC cord and plug repairs.

Do not use the unit if it does not work normally

• Unplug the unit from the power outlet if it emits smoke, an abnormal smell or

makes unusual noise. Consult an authorized service center for repairs.

Do not disassemble or repair the unit

• To reduce the risk of electric shock or fire, do not disassemble the unit. Contact

an authorized service center when service is required.

Use only the power source specified for the unit

• Overloading the unit by having many loads on one electrical outlet, etc. may cause

excessive heat resulting in fire.

Completely insert the power plug into the power outlet

• Failure to do so may cause electric shock and/or excessive heat resulting in a fire.

Do not use damaged power plugs or power outlets.

Regularly remove any dust, etc. from the power plug

• Regularly remove any dust, etc. from the power plug by pulling it from the power

outlet, then wiping with a dry cloth. Accumulated dust may cause an insulation

defect from moisture, etc., resulting in a fire.

Do not bring metal objects near the power outlet slots

• This may result in electric shock or fire.

Do not hold the power plug by the metal parts

• This may result in electric shock or fire.

Never touch the power plug with wet hands

• This may result in electric shock.

Operating Instructions 3

For Your Safety

Do not touch the unit, LAN cable, coaxial cable, AC cord, or power plug

during thunderstorms

• This may result in electric shock.

Do not use the included AC cord with other devices

• This may result in electric shock or fire.

Only use the included AC cord

• Using other AC cords may result in electric shock or fire.

Place the unit securely on a stable, level surface

• Serious damage and/or injury may result if the unit falls.

Do not install the unit in a dusty or moist place

• This may result in electric shock or fire.

Never push any objects into the unit or spill any liquids on the unit

• This may result in electric shock or fire. Disconnect the AC cord and contact an

authorized service center if any foreign objects or liquids enter the unit.

Regularly check the unit

• Rusted brackets or screws may cause the unit to fall causing serious damage

and/or injury. Consult an authorized dealer for checks.

Mount the unit to secure locations that can support the weight of the

unit

• Serious damage and/or injury may result if the unit falls. Reinforce the mounting

area if it has insufficient strength to secure the unit.

Make sure to use the safety wire

• Attach the safety wire in a position so that if the camera adaptor were to become

detached, it would not fall on nearby people.

Do not use the unit where it can be exposed to flammable or explosive

gasses

• This may cause the unit to explode resulting in injury.

Do not mount the unit where it can be exposed to vibrations

• This may cause the unit to fall resulting in injury.

Do not use the unit where it can be exposed to corrosive gas or salty

conditions

• This may cause the unit parts to degrade and the unit may fall resulting in damage

and/or injury.

Do not drop, or expose the unit to strong shaking

• This may result in electric shock or fire.

4 Operating Instructions

For Your Safety

Turn the power off before performing wiring

• This may result in electric shock, or result in fire from wiring shorts or incorrect

wiring.

Only use mounting brackets made for the unit

• Serious damage and/or injury may result if the unit falls.

Do not damage coaxial cables, insert objects into the conductor, or

connect coaxial cables with incomplete relays

• If water or other objects enter the conductor, or coaxial cables with incomplete

relays are connected, it may result in electric shock or fire. Disconnect the AC

cord and contact an authorized service center if there is any damage to the coaxial

cables.

Do not damage existing wires or pipes when making holes for mounting

or wiring

• This may result in earth leakage, electric shock, or fire.

Do not install or use the unit near medical equipment

• High-frequency signals emitted from the unit may affect the operation of medical

equipment and cause malfunctions.

Do not expose the unit to rain or any type of moisture

• To prevent the risk of fire or electrical shock, do not place objects such as cups

or vases near the unit. If the unit is exposed to moisture, disconnect the AC cord

and contact an authorized service center.

Do not touch the core of the coaxial cable

• A maximum of DC 60 V is applied to the coaxial cable. This may result in electric

shock.

Do not perform wiring or installation during thunderstorms

• This may result in electric shock or fire.

Secure screws with the specified torque

• Serious damage and/or injury may result if the unit falls.

CAUTION

Disconnect the AC cord of the center adaptor if the unit will not be used

for long periods of time or when performing care and cleaning

• Leaving the AC cord connected when the unit is not used for long periods of time

or when performing care and cleaning may result in earth leakage, electric shock,

or injury.

Operating Instructions 5

For Your Safety

Do not mount the unit to ceilings or walls made of soft materials

• Do not mount the unit to soft ceilings or walls such as plasterboard, ALC (aerated

light-weight concrete), concrete blocks, or any surfaces under 25 mm thickness.

Injury may result if the unit falls.

Do not pull cables or apply excessive force to connectors

• This may damage the cables or connectors, and result in electric shock.

Do not connect other devices to the BNC connector of the unit

• This may damage the unit.

Do not expose the unit to fire or naked flames

• This may result in fire.

The AC cord is used as the main disconnect device

• Ensure that the power outlet is installed near the unit and is easily accessible.

Do not play the included CD-ROM in an audio CD player

• Ear-splitting volume may hurt your ears and damage the CD player’s speakers.

6 Operating Instructions

For Your Safety

Important Safety Instructions

When using this unit, basic safety precautions should always be followed to reduce the

risk of fire, electric shock, or personal injury.

1. Do not use this unit near water for example, near a bathtub, washbowl, kitchen sink,

or laundry tub, in a wet basement or near a swimming pool.

2. Avoid handling or installing the unit, connecting wiring, or touching the AC cord,

power plug, LAN cable, or coaxial cable during an electrical storm.

3. Do not use the unit in the vicinity of a gas leak.

4. Use only the AC cord indicated in this manual.

SAVE THESE INSTRUCTIONS

Operating Instructions 7

Important Safety Instructions

General Precautions

Follow the instructions written in For Your Safety (see page 3) and Important Safety

Instructions (see page 7) together with the instructions written below.

1. The unit is intended for indoor use only and should not be mounted outdoors.

2. The unit uses the same high-frequency signals as used by the radio signals of

amateur radio, shortwave broadcasting, aviation radio, and marine radio. Therefore

operational interference may occur if the unit is used in proximity to devices that

transmit these radio signals.

3. Do not connect the camera adaptor (BY-HPE11R) to communications carrier

equipment such as rental modems.

4. Follow the following precautions in order to maintain product performance

over long periods of time.

• Do not use the unit in areas with high temperatures or humidity for long periods

of time. Use in these areas can degrade parts which can shorten the life-span of

the unit. We recommend areas that have temperatures of 35 °C or lower.

• Do not install the unit in places that can be directly exposed to heat sources.

5. Proper handling of the unit

• Do not drop, or expose the unit to strong vibrations or shaking. This may cause

malfunctions.

6. Take precautions for when reselling, disposing, or sending the unit for repairs.

• Take adequate precautions when handing the unit over to third parties.

7. Care and cleaning for the unit

• Perform cleaning and care after disconnecting the center adaptor from the power

outlet. Do not use benzine, thinner, or any other abrasive powders when

cleaning. This may change the color of the unit cases.

8. Cleaning stains from the unit

• Wipe stained areas with a damp soft cloth.

For FRG Users (For Germany Only)

• Machine noise information regulation - 3.GPSGV, the maximum sound pressure

level is 70 dB(A) or less, in conformity with EN ISO 7779.

• This device is not intended for use in the direct field of view at visual display

workplaces. To avoid incommoding reflexions at visual display workplaces this

device must not be placed in the direct field of view.

8 Operating Instructions

General Precautions

Table of Contents

1 Main Unit ...................................................................................................10

1.1 Camera Adaptor (BY-HPE11R) ......................................................................10

1.2 Center Adaptor (BY-HPE11H) ........................................................................12

1.3 Understanding the Indicators .......................................................................13

2 Resetting the Unit ....................................................................................14

2.1 Resetting Camera Adaptors ..........................................................................14

2.2 Resetting Center Adaptors ............................................................................15

3 Adaptor Maintenance Screen .................................................................16

3.1 Accessing the Maintenance Screen .............................................................17

3.1.1 Temporarily Changing the Computer’s IP Address ........................................17

3.1.2 Accessing the Maintenance Screen ...............................................................19

3.1.3 Maintenance Screen Overview ......................................................................21

3.1.4 System Requirements ....................................................................................22

3.2 Using the Maintenance Screen .....................................................................23

3.2.1 Updating the Adaptor’s Firmware ..................................................................23

3.2.2 Confirming the Adaptor’s Status ....................................................................24

3.2.3 Changing Adaptor Settings ............................................................................26

4 Troubleshooting ......................................................................................29

4.1 Indicator Display Issues ................................................................................29

4.2 Communication Speed Issues ......................................................................30

4.3 PoE Issues ......................................................................................................31

4.4 Other Issues ....................................................................................................31

5 Specifications ..........................................................................................32

Operating Instructions 9

Table of Contents

1 Main Unit

1.1 Camera Adaptor (BY-HPE11R)

Front view

CDE

AIndicator

Displays the status of the camera adaptor (see

page 13).

BPoE switch

Turns the PoE function ON/OFF. The default

setting is [ON].

IMPORTANT

• When using the camera adaptor’s PoE

function to supply power to a network

camera, set the PoE switch to [ON].

When not using the PoE function (when

powering the network camera with an

AC adaptor), set it to [OFF].

• The PoE function cannot be used for

connections over 500 m. Set the PoE

switch to [OFF].

CBNC connector

Connects the camera adaptor to the center

adaptor with a coaxial cable (see

3.2 Connections in the Installation Guide).

DNetwork connector

Connects the camera adaptor to a network

camera with a LAN cable (see

3.2 Connections in the Installation Guide).

EINITIAL SET button

Used to reset the camera adaptor to its factory

default settings (see page 14).

10 Operating Instructions

1 Main Unit

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Panasonic Medienkonverter Handbücher

Panasonic

Panasonic AWIF400G - PROTOCOL CONVERTER Bedienungsanleitung

Panasonic

Panasonic AJ-FRC27E Bedienungsanleitung

Panasonic

Panasonic BY-HPE11KTA Bedienungsanleitung

Panasonic

Panasonic WJ-GXE100 Bedienungsanleitung

Panasonic

Panasonic TU-DST50 Operating Bedienungsanleitung

Panasonic

Panasonic AG-DA100 Bedienungsanleitung

Panasonic

Panasonic Ramsa WZ-AD96 Bedienungsanleitung

Panasonic

Panasonic WJGXE900 - MPEG2 ENCODER Bedienungsanleitung

Panasonic

Panasonic WJ-GXE100 Bedienungsanleitung

Panasonic

Panasonic WJ-GXE500E Bedienungsanleitung

Panasonic

Panasonic KS1 Bedienungsanleitung

Panasonic

Panasonic WJ-GXD400 Handbuch

Panasonic

Panasonic EVB-MV103HFXX-KIT Bedienungs- und Wartungshandbuch

Panasonic

Panasonic AJ-UDC150AP Bedienungsanleitung

Panasonic

Panasonic i-pro WJ-NT304 Bedienungsanleitung

Panasonic

Panasonic WJDC108AD - DATA CONVERTER Bedienungsanleitung

Panasonic

Panasonic AJ-LT95 Bedienungsanleitung

Panasonic

Panasonic PC8 Bedienungsanleitung

Panasonic

Panasonic WJ-GXE500 Bedienungsanleitung

Panasonic

Panasonic AJ-YA455P Bedienungsanleitung

Panasonic

Panasonic WJDC108AD - DATA CONVERTER Bedienungsanleitung

Panasonic

Panasonic BY-HPE11KTA Bedienungsanleitung

Panasonic

Panasonic AJ-YDX30G Bedienungsanleitung

Panasonic

Panasonic AJUFC1800P - FORMAT CONVERTER Bedienungsanleitung

Beliebte Medienkonverter Handbücher anderer Marken

SoundTraxx

SoundTraxx Blunami BLU-2200 Bedienungsanleitung

SPROLINK

SPROLINK VA1 Bedienungsanleitung

Acclaim Lighting

Acclaim Lighting DDC-1-AC Bedienungsanleitung

Nikon

Nikon AF-S TC-20E III Bedienungsanleitung

Axis

Axis AXIS Q7406 Bedienungsanleitung

Omega

Omega TAC80B-J Bedienungsanleitung

Zoom

Zoom Thunderbolt TAC-2R Bedienungsanleitung

OST

OST iConverter 10/100M Bedienungsanleitung

Vertiv

Vertiv Netsure Bedienungsanleitung

birddog

birddog MINI Bedienungsanleitung

Roland

Roland GI-10 Bedienungsanleitung

Wallenstein

Wallenstein WX310 Bedienungsanleitung

Pace

Pace MSS 200-1 Bedienungsanleitung

Solar Converters

Solar Converters EQ 12/24-50 Bedienungsanleitung

CYP

CYP EL-7400V Bedienungsanleitung

TIE

TIE MIDI 1i1o Bedienungsanleitung

DCS

DCS Vivaldi Upsampler Bedienungsanleitung

Westermo

Westermo MCW-211 SERIES Bedienungsanleitung