Panasonic WVBM500 - B&W MONITOR Bedienungsanleitung

Video Monitor

WV-BM500

Before attempting to connect or operate this product,

please read these instructions completely.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION:

TO REDUCE THE RISK OF ELECTRIC

SHOCK, DO NOT REMOVE COVER (OR

BACK), NO USER SERVICEABLE PARTS

INSIDE.

REFER SERVICING TO QUALIFIED SERVICE

PERSONNEL.

The serial number of this product may be found on the bot-

tom of the unit.

You should note the serial number of this unit in the space

provided and retain this book as a permanent record of

your purchase to aid identification in the event of theft.

Model No.

Serial No.

The exclamation point within an equilat-

eral triangle is intended to alert the user

to the presence of important operating

and maintenance (servicing) instruc-

tions in the literature accompanying the

appliance.

FOR YOUR SAFETY PLEASE READ THE FOLLOWING TEXT CARE-

FULLY.

This appliance is supplied with a moulded three pin mains plug for your

safety and convenience.

A 5 amp fuse is fitted in this plug.

Should the fuse need to be replaced please ensure that the replacement

fuse has a rating of 5 amp and that it is approved by ASTA or BSI to

BS1362.

Check for the ASTA mark or the BSI mark on the body of the

fuse.

If the plug contains a removable fuse cover you must ensure that it is refit-

ted when the fuse is replaced.

If you lose the fuse cover the plug must not be used until a replacement

cover is obtained.

A replacement fuse cover can be purchased from your local Panasonic

Dealer.

IF THE FITTED MOULDED PLUG IS UNSUITABLE FOR THE SOCKET

OUTLET IN YOUR HOME THEN THE FUSE SHOULD BE REMOVED

AND THE PLUG CUT OFF AND DISPOSED OF SAFELY.

THERE IS A DANGER OF SEVERE ELECTRICAL SHOCK IF THE CUT

OFF PLUG IS INSERTED INTO ANY 13 AMP SOCKET.

If a new plug is to be fitted please observe the wiring code as shown

below.

If in any doubt please consult a qualified electrician.

WARNING: This apparatus must be earthed.

For U.K.

WARNING:

TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.

ENGLISH VERSION

The lightning flash with arrowhead sym-

bol, within an equilateral triangle, is

interned to alert the user to the pres-

ence of uninsulated "dangerous volt-

age" within the product's enclosure that

may be of sufficient magnitude to con-

stitute a risk of electric shock to per-

sons.

Cet appareil est conforme aux prescriptions de la

directive 87/308/C.E.E. (concernant les interférences

radio).

Dit modelis onderworpen aan de EEG-richtlijn (ter

voor-koming van radio-interferentie) 87/308/EGG.

Denne model opfylder EF direktiv 87/308/EF (for for-

ebyggelse af radiointerferens).

Este modelo cumple con la norma EC (para interfer-

encias de radio 87/308/EEC).

La Società PANASONIC ITALIA S.p.A., importatrice di

questo prodotto, dichiara che questo apprarecchio è

conforme alle disposizioni della direttiva

C.E.E./87/308 (D.M. 13 aprile 1989).

IMPORTANT

The wires in this mains lead are coloured in accordance with the following

code. Green-and-yellow: Earth

Blue: Neutral

Brown: Live

As the colours of the wire in the mains lead of this appliance may not

correspond with the coloured markings identifying the terminals in your

plug, proceed as follows.

The wire which is coloured green-and-yellow must be connected to

the terminal in the plug which is marked with the letter E or by the earth

symbol or coloured green or green-and-yellow.

The wire which is coloured blue must be connected to the terminal in

the plug which is marked with the letter N or coloured black.

The wire which is coloured brown must be connected to the terminal

in the plug which is marked with the letter L or coloured red.

How to replace the fuse

Open the fuse compartment with

a screwdriver and replace the fuse

and fuse cover.

THIS APPARATUS MUST BE EARTHED.

To ensure safe operation the three-pin plug supplied must be inserted

only into a standard three-pin power point which is effectively earthed

through the normal household wiring. Extension cords used with the

equipment must be three-core and be correctly wired to provide con-

nection to earth. Wrongly wired extension cords are a major cause of

fatalities.

The fact that the equipment operates satisfactorily does not imply that

the power point is earthed and that the installation is completely safe.

For your safety, if in any doubt about the effective earthing of the

power point, consult a qualified electrician.

This apparatus was produced to BS 800:1987.

This model conforms of the EC directive (for radio interference)

87/308/EEC.

For U.K.

For Australia

ENGLISH

-1-

CONTENTS

PREFACE ....................................................................................................................................................................... 2

FEATURES ..................................................................................................................................................................... 2

PRECAUTIONS .............................................................................................................................................................. 2

MAJOR OPERATING CONTROLS AND THEIR FUNCTIONS ........................................................................................ 3

OPERATING PROCEDURE ............................................................................................................................................ 5

INSTALLATION .............................................................................................................................................................. 6

CONNECTIONS ............................................................................................................................................................. 7

SYSTEM CONNECTIONS .............................................................................................................................................. 8

SPECIFICATIONS .......................................................................................................................................................... 9

STANDARD ACCESSORIES ......................................................................................................................................... 10

The model numbers listed in this Operating Instructions have no suffixed attached to it.

-2-

PREFACE

• The Panasonic WV-BM500 is a desk-top closed

circuit Video Monitor especially designed for sur-

veillance and studio applications.

WV-BM500 features a 5” screen (diagonal actual

visual size) and produces sharp, black-and-white

pictures with horizontal resolution of more than 700

lines at center.

Front mounted controls permit fast picture adjust-

ment. Standard BNC-type input and output con-

nectors enables WV-BM500 to be used with other

CCTV monitors or Panasonic Video Tape

Recorder.

FEATURES

• 5’’ screen (diagonal actual visual size).

• Horizontal resolution 700 lines at center.

• Short H. AFC time constant for VTR playback.

• Bridging input and output connectors for video

and composite sync.

• DC restoration.

• Internal and External Sync mode.

• By using the Optional Rack Angle Bracket WV-

Q64, rack mounting is available.

PRECAUTIONS

• This unit is designed for indoor use. Operable

ambient temperature range must not exceed

beyond

−10°C - +50°C (14°F - 122°F), and permis-

sible humidity is less than 90%. Avoid using the

monitor under direct sunIight.

• The input power source is 220 - 240V AC 50 Hz .

• Do not block the ventilation slots on the rear panel

and side cover.

• When mounting the Model WV-BM500 in an EIA

standard 19” rack, be careful to insure that the

interior temperature of the rack does not exceed

+50°C (122°F).

-3-

MAJOR OPERATING CONTROLS AND THEIR FUNCTIONS

1. Power On/Off Switch (POWER, ON/OFF)

This is a push-push type switch which turns the

power of this monitor on and off.

Press once and the switch remains down (;) for

turning on the power of monitor.

Press again, the switch comes up (l) for turning

off the power of the monitor.

2. Power Indicator (POWER)

By turning on the Power On/Off Switch (1), this

indicator lights.

!1 !2 !3 !4 !5 !6

H.HOLD V.LIN

HEIGHT

POWER

OFF

Video Monitor WV-BM

500

V.HOLD BRIGHT FOCUS

CONTRAST

-4-

3. Horizontal Hold Control [H-HOLD]

This control is used to Lock in the picture horizon-

tally.

4. Height Control [HEIGHT]

Adjust the vertical height of the picture.

5. Vertical Hold Control [V-HOLD]

This control is used to Lock in the picture vertical-

ly.

6. Vertical Linearity Control [V-LIN]

Adjust for vertical distortion of the picture.

7. Bright Control [BRIGHT]

Turn this control clockwise to increase the overall

brightness.

8. Focus Control [FOCUS]

Adjust for the clearest picture.

9. Contrast Control [CONTRAST]

Turn this control clockwise to increase the picture

contrast .

10. DC Restoration Switch [DC REST]

Switch to restore background of picture.

11. Video Input Connector (VIDEO IN)

This connector accepts the input video signal

12. Video Output Connector (VIDEO OUT)

The video input signal connected to the Video

Input Connector (11) is looped through to this con-

nector and terminated automatically.

13. Sync Selector Switch [SYNC INT/EXT]

14. Sync Input Connector [SYNC IN]

15. Sync Output Connector [SYNC OUT]

16. AC Power Cord

-5-

OPERATING PROCEDURE

1. Set the Power On/Off Switch (1) to the ON (;)

position.

2. Adjust the Bright Control (7) and Contrast Control

(9).

3. Adjust the Horizontal Hold

(3) until the picture is sta-

bilized, if the picture slips

to either side, or appears

as a series of horizontal

stripes.

4. Adjust the Vertical Hold

(5), if the picture rolls up

or down.

BRIGHT CONTRAST

H.HOLD

V.HOLD

increaseincrease

5. Height (4)

This recessed screwdriver control should be

adjusted simultaneously to give proper vertical

height consistent with good vertical linearity.

Adjustment should be made to extend the picture

limits approximately 1/10” beyond the top and bot-

tom edges of the mask at over scanning operation.

6. Vertical Linearity (6)

This recessed screwdriver control should be

adjusted to give proper vertical linearity.

7. Focus (8)

The clearest picture is produced when this screw-

driver control is adjusted.

8. DC Restoration (10)

DC restoration circuit provides a stable reference

for the black level. Set the switch to ON position to

prevent excessive contrast and preserve shadow

detail.

-6-

INSTALLATION

CAUTION:

The following installation should be made by qualified

service personnel or system installers.

Mounting into EIA Standard 19” Rack

Model WV-BM500 can be mounted into EIA 19” rack as

shown below.

Note: Rack Mounting requires the purchase of optional

WV-Q64 Rack Angle Bracket.

WV-BM500

Rack Panel

Rack Mount Chassis

Rack Mount Screws

(Not Supplied)

Washer

(Part No. YWL1201ER01)

Fixing Screws

(Part No. YWL831-EM01A)

EIA

Rack

-7-

CONNECTIONS

Power Cable

1. Keep the camera Power switched OFF during

installation.

2. Connect the Power Cord (16) to a 50 Hz grounded

electrical outlet 220-240V AC .

Video Cable

1. Use the RG-59/U (3C-2V), RG-6/U (5C-2V). RG-

11/U (7C-2V) or RG-15/U (10C-2V) coaxial cable.

2. Up to 10 monitors can be hooked up in this config-

uration before signal loss occurs. Total cable

length should not exceed 500 feet (150m).

3. Wiring Precautions

• Do not bend coaxial cable into a curve whose

radius is smaller than 10 times of its diameter.

• Never crush or pinch the cable

All these will change the impedance of the cable

and cause poor picture quality

Cable RG-59/U RG-6U RG-11/U RG-15/U

(3C-2V) (5C-2V) (7C-2V) (10C-2V)

Recommended (m) 500 750 1000 1250

maximum

cable length (ft) 1650 2475 3300 4125

Recommended maximum cable length

External Sync

When a non-composite video signal is connected to

the monitor, it will be necessary to connect an external

composite sync signal to the monitor.

1. Connect the Sync Input Connector (14) on the

video monitor to the sync signal source by means

of a 75Ωcoaxial cable.

2. Set the Sync Selector Switch (13) at EXT position.

NOTE:

1. Non-composite video signal is a signal without

sync.

2. External sync should be composed of mixed H.

Sync and V. sync signals, not H. and V. drive

pulse signals. Composite Sync Level:

4.0 Vp-p (2.0 Vp-p −5.0 Vp-p)

Andere Handbücher für WVBM500 - B&W MONITOR

Inhaltsverzeichnis

Andere Panasonic Monitor Handbücher

Panasonic

Panasonic WVBM1400 - B&W CAMERA Bedienungsanleitung

Panasonic

Panasonic TH-75BQE1W Bedienungsanleitung

Panasonic

Panasonic TH-86EQ1W Bedienungsanleitung

Panasonic

Panasonic TH-42LF30U Bedienungsanleitung

Panasonic

Panasonic TH-103PF12E Bedienungsanleitung

Panasonic

Panasonic TH-32LHD7B Bedienungsanleitung

Panasonic

Panasonic TH-42PH10BK Bedienungsanleitung

Panasonic

Panasonic LH-43RM1MX Bedienungsanleitung

Panasonic

Panasonic TH-103PF12U Betriebsanleitung

Panasonic

Panasonic PT-51HX42CF Bedienungsanleitung

Panasonic

Panasonic TH-50PM50U Bedienungsanleitung

Panasonic

Panasonic TH47LF20U - 47" HD LCD TV Bedienungsanleitung

Panasonic

Panasonic TH-42LF20W Bedienungsanleitung

Panasonic

Panasonic TH-47LFT30W Bedienungsanleitung

Panasonic

Panasonic CYVM5800U - 5.8" CLR MONITOR/DVD Bedienungsanleitung

Panasonic

Panasonic WV-CK2020A - 20" CRT Display Bedienungsanleitung

Panasonic

Panasonic TH-103PF9WK Bedienungsanleitung

Panasonic

Panasonic VL-DM200BX Bedienungsanleitung

Panasonic

Panasonic TH-42PH10EK Bedienungsanleitung

Panasonic

Panasonic TH-65PF30W Bedienungsanleitung

Panasonic

Panasonic TH-42PF11EK Bedienungsanleitung

Panasonic

Panasonic TH-37PH9UK Bedienungsanleitung

Panasonic

Panasonic CF-VDL01 Bedienungsanleitung

Panasonic

Panasonic CT-1030M Bedienungsanleitung

Beliebte Monitor Handbücher anderer Marken

Linear Acoustic

Linear Acoustic LQ-1000 Bedienungsanleitung

AOC

AOC I2579V Bedienungsanleitung

Gateway

Gateway FPD1520 Bedienungsanleitung

Furuno

Furuno Mu 120c Bedienungsanleitung

Asus

Asus VB171D - 17" LCD Monitor Bedienungsanleitung

Dell

Dell S2230MX Gebrauchsanweisung

Philips

Philips 107C64 Bedienungsanleitung

Dell

Dell S2409WFP Bedienungsanleitung

EverFocus

EverFocus EN-7517E Bedienungsanleitung

Dell

Dell Precision 7680 Bedienungsanleitung

LG 50PM1M - - 50" Plasma Panel Bedienungsanleitung

Bosch

Bosch DDU 9 Bedienungsanleitung

Acer

Acer A231HL Bedienungsanleitung

Philips

Philips 86BDL4152T Bedienungsanleitung

NEC

NEC AccuSync LCD5V Bedienungsanleitung

Emay

Emay SleepO2 Bedienungsanleitung

IBM

IBM 6360 Montageanleitung

Acer

Acer CB382CUR Bedienungsanleitung