Panasonic Grid-EYE Bedienungsanleitung

QUICK START GUIDE

Grid-EYE Evaluation Kit

QUICK START GUIDE

Grid-EYE Evaluation Kit

Panasonic Automotive & Industrial Systems Europe GmbH Quick Start Guide

Please visit www.eu.industrial.panasonic.com/grideye-evalkit for latest documentation and

software downloads and updates.

Operating modes for the Evaluation Kit

Following two operation modes are possible:

Independent Mode:

1. On-board microcontroller is used to read-out and process the sensor data. Direct

USB / Bluetooth Low Energy connection is available.

Arduino Shield Mode:

2. Any 3.3V Arduino board (e.g. Arduino DUE) can be used as mother board to read out

Grid-EYE and send data via USB and Bluetooth.

For both modes, Windows LabVIEW Demonstration software is available. Other multi-

platform software examples, such as Grid-EYE API and Python source code, can also be

found on Panasonic Website www.eu.industrial.panasonic.com/grideye-evalkit.

WARNING

The jumper shunt for the pin-header designated J18 must not be placed on the

pin-header prior to using the board, unless the intent is to access the

Bootloader. By default this jumper is removed from the J18 header and placed

inside the box separately for later use.

The Grid-EYE board has Arduino headers soldered on for convenience, should

the user choose to host the board onto an Arduino (DUE) mother board. Users

are reminded to be careful so not short-out the pins or have the board resting

on a conductive surface.

Panasonic Automotive & Industrial Systems Europe GmbH Quick Start Guide

Windows Demonstration Software - LabVIEW Application Installation:

1. Go to www.eu.industrial.panasonic.com/grideye-evalkit and download the LabVIEW

Demo Software package.

(LabVIEW Run-Time Support is included)

2. Open the zip file and run “setup.exe”.

3. After installation, connect the Grid-EYE board via USB to the PC. Red LED will blink

indicating data transfer.

4. Open Control Panel >> Device Manager and check COM port of the device:

It is detected as a ‘Grid Eye Sensor Board (COM X)’. (If it is not detected, please

reinstall the USB driver from the Panasonic homepage or

www.eu.industrial.panasonic.com/grideye-evalkit)

5. Run Grid-EYE application (Windows Start >> Grid-EYE >> Open Grid-EYE

application).

(If compatibility issues are encountered , reinstall the LabVIEW Run-Time Engine

2014 from www.ni.com or from supplied folders containing both 32bit and 64bit

versions)

6. Select the appropriate COM-port. Click ‘Open COM’to view the data fed to the PC

from the Grid-EYE sensor.

7. Temperature values can be observed on the LabVIEW (8 x 8) matrix window.

Colours for the heat map can be set between -20°C and +100°C. The second

tab shows an interpolation of the raw signal.

Panasonic Automotive & Industrial Systems Europe GmbH Quick Start Guide

Data via Bluetooth:

Please be aware of the fact that only a text based interface showing raw data is available at

the moment. Please check www.eu.industrial.panasonic.com/grideye-evalkit for updates and

smart phone apps coming soon.

1. Please go to App Store (iPhone)/ Google Play (Android) and install DSPS (Dialog

Serial Port Service) application from “JUMA Technology”.

iPhone(https://itunes.apple.com/us/app/dsps/id953430079?mt=8

Android

(https://play.google.com/store/apps/details?id=com.dialog_semiconductor.dsps )

2. Turn Bluetooth ‘ON’ on the Android/Apple device and open DSPS

3. Search /scan for the device.

4. When detected the blue LED on the Grid-EYE board lights up.

5. The device will be detected on the application –select Grid-EYE device to see data

come through.

Use as Arduino Shield:

As the Grid-EYE and the Bluetooth Module are working with 3.3V, only Arduino Boards with

3.3V supply voltage are supported (e.g. Arduino Due)

1. Open www.eu.industrial.panasonic.com/grideye-evalkit and download software for

Arduino board.

2. Plug-in the Grid-EYE Sensor board to a 3.3V Arduino mother board.

3. Remove Jumpers J7, J9, J10 and J12 at the Grid-EYE board.

4. Connect USB interfaces and power-up the Arduino and GridEYE boards.

5. Open Device Manager to check the COM port.

6. Open LabVIEW application with appropriate COM port for the GridEYE board.

8. Click ‘Open COM’to view the data. Temperature values can be observed on the

LabVIEW (8 x 8) matrix window. Colours for the heat map can be set between -20°C

and +100°C. The second tab is showing an interpolation of the raw signal.

7. Open the DSPS application and view sensor data via Bluetooth.

Panasonic Automotive & Industrial Systems Europe GmbH Quick Start Guide

Compliance Information :

CAN ICES-3 (B)/NMB-3(B) | Contains FCC ID: T7V1740

| Contains IC: 216Q-1740

This device complies with Part 15 of the FCC Rules. Operation is subject to the following

two conditions:

(1) this device may not cause harmful interference, and (2) this device must accept any

interference received, including interference that may cause undesired operation.

Note: This equipment has been tested and found to comply with the limits for a Class B

digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference in a residential installation. This

equipment generates, uses and can radiate radio frequency energy and, if not installed and

used in accordance with the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference will not occur in a

particular installation. If this equipment does cause harmful interference to radio or television

reception, which can be determined by turning the equipment off and on, the user is

encouraged to try to correct the interference by one or more of the following measures:

—Reorient or relocate the receiving antenna.

—Increase the separation between the equipment and receiver.

—Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

—Consult the dealer or an experienced radio/TV technician for help.

For more information visit: eu.industrial.panasonic.com/grideye-evalkit

Andere Handbücher für Grid-EYE

Inhaltsverzeichnis

Andere Panasonic Hauptplatine Handbücher

Panasonic

Panasonic NN32251A Bedienungsanleitung

Panasonic

Panasonic PGA26E07BA-SWEVB008 Bedienungsanleitung

Panasonic

Panasonic PAN9320ETU Bedienungsanleitung

Panasonic

Panasonic NN30320A Bedienungsanleitung

Panasonic

Panasonic EVB-NN30312A Bedienungsanleitung

Panasonic

Panasonic Grid-EYE Bedienungsanleitung

Panasonic

Panasonic AN33014UA Bedienungsanleitung

Panasonic

Panasonic PAN9520 Bedienungsanleitung

Panasonic

Panasonic PGA26E07BA-SWEVB006 Bedienungsanleitung

Panasonic

Panasonic AN30182A-EVB Bedienungsanleitung

Panasonic

Panasonic PAN9420 Bedienungsanleitung

Panasonic

Panasonic PAN1311/21 USB Bedienungsanleitung

Panasonic

Panasonic EvalBoard PAN4555 Bedienungsanleitung

Panasonic

Panasonic PAN4570 Bedienungsanleitung

Beliebte Hauptplatine Handbücher anderer Marken

DFI

DFI SD170 Bedienungsanleitung

ASROCK

ASROCK ROMED8-2T Bedienungsanleitung

Asus

Asus P2L97A Bedienungsanleitung

Winmate

Winmate IC70 Bedienungsanleitung

Asus

Asus MES-B Bedienungsanleitung

Grantech

Grantech SYS8F377VGGA-3OMN Bedienungsanleitung

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Bedienungsanleitung

Texas Instruments

Texas Instruments ADS8372EVM Bedienungsanleitung

Commell

Commell MS-C73 Bedienungsanleitung

Gigabyte

Gigabyte GA-9IVDT Bedienungsanleitung

IBT Technologies

IBT Technologies MB860 Bedienungsanleitung

Nvidia

Nvidia TEGRA DG-04927-001_V01 Bedienungsanleitung

Intel

Intel D33217CK Bedienungsanleitung

Asus

Asus F1A55-M LX PLUS R2.0 Bedienungsanleitung

EPC

EPC EPC9147C Bedienungsanleitung

Asus

Asus EX-B760M-V5 D4 Bedienungsanleitung

EPOX

EPOX MU-8KHA0010 Bedienungsanleitung

Ski-Doo

Ski-Doo Bombardier MPEM 219 700 090 Bedienungsanleitung