Panasonic EY4550 Bedienungsanleitung

Operating Instructions

Bedienungsanleitung

Instructions d’utilisation

Istruzioni per l’uso

Gebruiksaanwijzing

Manual de instrucciones

Brugsvejledning

Driftsföreskrifter

Bruksanvisning

Käyttöohjeet

Before operating this unit, please read these instructions completely and save this manual for future use.

Vor Inbetriebnahme des Gerätes die Betriebsanleitung bitte gründlich durchlesen und diese Broschüre zum späteren Nachschlagen

sorgfältig aufbewahren.

Lire entièrement les instructions suivantes avant de faire fonctionner l’appareil et conserver ce mode d’emploi à des fins de consultation

ultérieure.

Prima di usare questa unità, leggere completamente queste istruzioni e conservare il manuale per usi futuri.

Lees deze gebruiksaanwijzing aandachtig door voor u het apparaat in gebruik neemt en bewaar de gebruiksaanwijzing voor eventuele

naslag.

Antes de usar este aparato por primera vez, lea todas las instrucciones de este manual y guarde el manual para poderlo consultar en el

futuro.

Gennemlæs denne betjeningsvejledning før brugen og gem den til fremtidig brug.

Läs igenom hela bruksanvisningen innan verktyget tas i bruk. Spara bruksanvisningen för senare användning.

Før enheten tas i bruk, vennligst les disse alle anvisningene og oppbevar deretter bruksanvisningen for senere bruk.

Lue ohjeet huolella ennen laitteen käyttöönottoa ja säilytä tämä käyttöohje tallessa tulevaa tarvetta varten.

Cordless Jigsaw

Kabellose Stichsäge

Meule d'angle sans fil

Seghetto senza filo

Snoerloze decoupeerzaag

Sierra inalámbrica

Akku-dekupørsav

Sladdlös sticksåg

Oppladbar Stikksag

Ladattava pistosaha

Model No: EY4550

- 9 -

Original instructions: English

Translation of the original instructions:

Other languages

I. INTENDED USE

Thank you for purchasing the

Panasonic Jigsaw. This jigsaw can be

used with Panasonic rechargeable

batteries to provide excellent cutting

performance. The jigsaw is for cutting

metal, wood, and drywall only.

Read the “Safety Instructions” booklet

and the following before using.

II. ADDITIONAL

SAFETY RULES

1) Hold tool by insulated gripping

surfaces when performing an

operation where the cutting tool

may contact hidden wiring.

Contact with a “live” wire will also

make exposed metal parts of the

tool “live” and shock the operator.

2) Use clamps or another practical

way to secure and support the

workpiece to a stable platform.

Holding the work by hand or against

your body leaves it unstable and

may lead to loss of control.

3) Keep hands away from cutting

area and blade. Keep your

insulated gripping surfaces. If

both hands are holding the tool, they

cannot be cut by the blade.

4) Never hold piece being cut in

your hands or across your leg. It

is important to support the work

properly to minimize body exposure

or loss of control.

5) Be aware that this tool is always

in an operating condition, since it

does not have to be plugged into

an electrical outlet.

6) Always use safety goggles or

glasses with side shields.

Ordinary eye or sun glasses are

NOT safety glasses.

7) When this tool is used for

woodworking in confined areas

(e.g. indoors), wear dust mask.

8) Avoid cutting nails. Inspect

workpiece for any nails and

remove them before operation.

9) Do not cut oversized workpiece.

10) Check for the proper clearance

beyond the workpiece before

cutting so that the blade will not

strike the floor, workbench, etc.

11) Hold the tool firmly.

12) Make sure the blade is not

contacting the workpiece before

the switch is turned on.

13) Keep hands away from moving

parts.

14) Do not touch the blade or

workpiece immediately after

operation; they may be extremely

hot and could burn your skin.

15) Never swing tool.

16) Do not use blades which are

deformed or cracked.

17) Do not use blades which do not

comply with the characteristics

specified in these instructions.

- 10 -

18) Remove the battery pack from the

tool body before replacement of

the blade, making adjustments,

or other maintenance work.

19) Wear ear protectors when using

the tool for extended periods.

Symbol Meaning

V Volts

Direct current

n0No load speed

…min

-1

Revolutions or

reciprocations per minutes

Ah Electrical capacity of

battery pack

To reduce the risk of

injury, user must read

and understand

instruction manual.

For indoor use only.

WARNING:

• Do not use other than the

Panasonic battery packs that are

designed for use with this

rechar

eable tool.

• Panasonic is not responsible for

any damage or accident caused

by the use of the recycled battery

pack and the counterfeit battery

pack.

• Do not dispose of the battery pack

in a fire, or expose it to excessive

heat.

• Do not drive the likes of nails into

the battery pack, subject it to

shocks, dismantle it, or attempt to

modif

it.

• Do not allow metal objects to

touch the batter

pack terminals.

• Do not carry or store the battery

pack in the same container as

nails or similar metal ob

ects.

• Do not charge the battery pack in

a high-temperature location, such

as next to a fire or in direct

sunlight. Otherwise, the battery

may overheat, catch fire, or

explode.

• Never use other than the

dedicated charger to charge the

battery pack. Otherwise, the

battery may leak, overheat, or

explode.

• After removing the battery pack

from the tool or the charger, always

reattach the pack cover. Otherwise,

the battery contacts could be

shorted, leadin

to a risk of fire.

• When the Battery Pack Has

Deteriorated, Replace It with a

New One. Continued use of a

damaged battery pack may result

in heat generation, ignition or

battery rupture.

III.ASSEMBLY

WARNING:

To reduce the risk of injury, always

remove battery pack before changing

the blade.

Inspection before use

• Has the correct jigsaw blade been

attached for the object to be cut?

• Has the correct stem shape and

thickness of the blade been

mounted?

• Check if the blade is fixed securely?

• Check if the blade is cracked or broken.

• Check that there are no foreign objects

in the object to be cut.

Installing and removing the blade

Installation

1. The dust cover is removed.

2. Wipe away any cutting dust from the

blade and the blade clamp bracket.

3. Pull the blade Attach/Remove lever.

- 11 -

4. • Insert the blade into the blade

clamp bracket and set the back of

the blade along the roller guide so

that the back of the jigsaw blade

slides along the roller guide.

• Make sure the sten of blade is

deep enough inserted until the

blade projection is fixed by blade

clamp.

5. Release the blade Attach/Remove

lever.

• Check that the back of blade is along

the roller guide and set straight.

WARNING:

If you do not insert the saw blade

deep enough, the saw blade may be

ejected unexpectedly during

operation. This can be extremely

dangerous.

Removal

1. Pull the blade Attach/Remove lever.

2. Pull out the blade.

Adjusting the base

1. Use the hex wrench to loosen the

base fixing screw.

2. Move the base along the base

adjustment hole to set its position.

(See the diagram at right.)

• The base can be adjusted to between

0° and 45° sideways and the

forward/back position can also be

adjusted. If tilting the base sideways,

remove the dust cover first.

• Refer to the bevel index to determine

the angle.

• Rip fence fixing screw should be

located on the opposite side tool is

beveled.

3. Use the hex wrench to tighten the

base fixing screw.

Roller guide

- 12 -

Position of base and purpose of use

Base adjustment

hole position Purpose of use

Normal right-angled

cutting

Cutting at an angle

between 0° and 45°

NOTE:

This is only a rough guide. The

actual angle of the cut will be

affected by factors such as the way

the tool is held against the surface.

Adjusting the orbital stroke mode

• Adjust the orbital stroke mode to the

object to be cut.

Lever

position

Blade

movement

Main

applications

Vertical only

• Cutting hard

metals such as

steel

• Smooth cutting of

building materials

and plywood

boards

• Cutting around

small curves

Low orbital stroke

mode

• Cutting softer

metals such as

aluminum and

other non-ferrous

metals

• Cutting hardwood,

plywood boards

and plastics

Medium orbital

stroke mode

• Cutting fairly soft

materials

• Cutting wood and

composite boards

• High-speed

cutting of

aluminum and soft

steel

High orbital

stroke mode

• Cutting soft

materials

• High-speed

cutting of

materials such as

wood, composite

boards and

plastics

• If you would like to produce a cleaner

finish, set the orbital stroke mode to

a lower level.

- 13 -

Blowing lever

Select dust blow mode.

:OFF :ON

Dust adapter for vacuum cleaner

(EY9X016) (Available as an accessory,

not included)

You can use a vacuum cleaner to

collect cutting dust while cutting.

Installation

1. Attach the hook of the dust collection

adapter to the front of the base.

2. Snap the rear to install it.

3. Attach the hose of the vacuum cleaner.

• It is recommended to use a dust adapter

for reducing the risk of damaging the

surface of the object being cut.

Attaching or Removing Battery

Pack

1. To connect the battery pack:

Line up the alignment marks and attach

the battery pack.

• Slide the battery pack until it locks

into position.

2. To remove the battery pack:

Pull the button from the front to

release the battery pack.

Button

lignment

marks

- 14 -

IV. OPERATION

1. Push the switch lock lever down, pull

the power switch.

• The speed increases with the amount

of depression of the power switch.

2. Once cutting is finished, release the

power switch.

3. Check that the temperature of the

blade has dropped sufficiently, and

then remove the blade.

CAUTION:

When operating the tool by pulling the

trigger, there may be a momentary lag

before rotation starts. This does not

signal a malfunction.

•This lag occurs as the tool’s circuitry

starts up when the trigger is pulled

for the first time after installing a new

battery pack or after the tool has not

been used for at least 1 minute (or at

least 5 minutes when the LED is on).

Rotation will start without any lag

during second and subsequent

operations.

Cutting

NOTE:

• Check that there are no obstacles to

cut underneath workpiece.

• Check that there are no objects such

as nails in the material to be cut.

If the blade comes into contact with any

such objects during cutting, a strong

reaction force will be generated and

severe injury may occur.

• Do not place your hand on the object

in the direction cutting is to take place.

If this is not observed, there is a risk

of injury.

• Do not touch the jigsaw blade

immediately after cutting.

If this is not observed, burns may occur.

Cutting along marked lines

1. Place the object to be cut onto the

base, and align the blade with the

marked line.

• Do not touch the blade against the

object to be cut before pulling the

power switch.

2. Pull the power switch, wait until the

speed has stabilized, and then place

the base against the object to be cut

and cut along the marked lines.

• When cutting complex shapes such

as shapes with many small curves,

reduce the cutting speed and the

turning speed.

- 15 -

Plunge cutting

1. Make a drill hole in the section to be

plunge cut in order to let the blade

pass through.

2. Insert the blade into a hole without

touching the workpiece, and then

turn on the power switch.

3. Cut along the marked line.

Usingaripfence

A rip fence can be used for cutting

parallel lines and for cutting circles

and arcs.

Installing the rip fence

1. Loosen the rip fence fixing screw.

Pass the rip fence through the mount.

3. Adjust the cutting position and then

tighten the fixing screw.

Cutting at the same width

1. Place the base onto the workpiece

so that the edge of the rip fence

and workpiece are put together.

2. Without letting the blade touch the

workpiece, turn on the power switch.

3. Face the rip fence firmly to the

workpiece to cut parallel line.

WARNING:

Do not inhale any smoke emitted

from the tool or battery pack as it may

be harmful.

CAUTION:

Do not use the tool in a manner that

causes the motor to lock up. Doing so

may damage the tool and battery

pack, resulting in smoke or fire.

- 16 -

Control Panel

(1) (3)

(2)

(1) LED light

Before the use of LED

light, always pull the

power switch once.

Press the LED

light button.

The light illuminates

with very low current,

and it does not

adversely affect the

performance of the

driver during use or

its battery capacity.

CAUTION:

• The built-in LED light is designed to

illuminate the small work area

temporarily.

• Do not use it as a substitute for a

regular flashlight, since it does not

have enough brightness.

• LED light turns off when the tool has

not been used for 5 minutes.

Caution : DO NOT STARE INTO BEAM.

Use of controls or adjustments or performance

of procedures other than those specified

herein may result in hazardous radiation

exposure.

(2) Overheat warning lamp

Off

(normal

operation)

Flashing: Overheat

Indicates operation has

been halted due to

battery overheating.

To protect the motor or battery, be

sure to note the following when car-

rying out this operation.

• If the motor or battery becomes hot,

the protection function will be

activated and the motor or battery will

stop operating. The overheat warning

lamp on the control panel illuminates

or flashes when this feature is active.

• If the overheating protection feature

activates, allow the tool to cool

thoroughly (at least 30 minutes). The

tool is ready for use when the overheat

warning lamp goes out.

• Avoid using the tool in a way that

causes the overheating protection

feature to activate repeatedly.

• If the tool is operated continuously

under high-load conditions or if it is

used in hot-temperature conditions

(such as during summer), the

over-heating protection feature may

activate frequently.

• If the tool is used in cold-temperature

conditions (such as during winter) or if

it is frequently stopped during use, the

overheating protection feature may not

activate.

• The ambient temperature range is

between 0°C (32°F) and 40°C (104°F).

If the battery pack is used when the

battery temperature is below 0°C

(32°F), the tool may fail to function

properly.

• When charging a cool battery pack

(below 0°C (32°F)) in a warm place,

leave the battery pack at the place and

wait for more than one hour to warm up

the battery to the level of the ambient

temperature.

- 17 -

(3) Battery low warning lamp

Excessive (complete) discharging of

lithium ion batteries shortens their

service life dramatically. The tool

includes a battery protection feature

designed to prevent excessive dis-

charging of the battery pack.

• The battery protection feature

activates immediately before the

battery loses its charge, causing the

battery low warning lamp to flash.

• If you notice the battery low warning

lamp flashing, charge the battery

pack immediately.

• If it is started with too little battery

power remaining, the tool may stop

operating without the battery low

warning lamp flashing first. This

indicates that there is too little

battery power remaining to use the

tool, and the battery pack should be

charged before further use.

• If the tool is subject to a sudden load

during use that causes the motor to

lock up, the overdischarge

prevention sensor may be triggered,

and the battery low warning lamp

may flash. The lamp will stop

flashing once you address the

cause of the motor’s locking up and

cycle the trigger.

[Battery Pack]

For Appropriate Use of

Battery pack

Li-ion Battery pack

• For optimum battery life, store the

Li-ion battery pack following use

without charging it.

• When charging the battery pack,

confirm that the terminals on the

battery charger are free of foreign

substances such as dust and water etc.

Clean the terminals before charging

the battery pack if any foreign

substances are found on the terminals.

The life of the battery pack terminals

may be affected by foreign

substances such as dust and water

etc. during operation.

• When battery pack is not in use, keep

it away from other metal objects like:

paper clips, coins, keys, nails, screws,

or other small metal objects that can

make a connection from one terminal

to another.

Shorting the battery terminals together

may cause sparks, burns or a fire.

• When operating the battery pack,

make sure the work place is well

ventilated.

• When the battery pack is removed

from the main body of the tool,

replace the battery pack cover

immediately in order to prevent dust

or dirt from contaminating the battery

terminals and causing a short circuit.

Off

(normal

operation)

Flashing

(No charge)

Battery protection

feature active

Andere Handbücher für EY4550

Inhaltsverzeichnis

Andere Panasonic Elektrowerkzeuge Handbücher

Panasonic

Panasonic EY4541 Bedienungsanleitung

Panasonic

Panasonic EYFLA4A Bedienungsanleitung

Panasonic

Panasonic EY74A2X Bedienungsanleitung

Panasonic

Panasonic EYFEA1N Betriebsanleitung

Panasonic

Panasonic EY7440 - DRILL DRIVER 14.4V- MULTI-LANG Bedienungsanleitung

Panasonic

Panasonic EY75A8 Bedienungsanleitung

Panasonic

Panasonic EYFPA1C Bedienungsanleitung

Panasonic

Panasonic EY4542 - CIRCULAR SAW 14.4V Bedienungsanleitung

Panasonic

Panasonic EYFPA1C Bedienungsanleitung

Panasonic

Panasonic EY3610 Bedienungsanleitung

Panasonic

Panasonic EYFLA9C Bedienungsanleitung

Panasonic

Panasonic EY4541 Bedienungsanleitung

Panasonic

Panasonic 4541OLOA Bedienungsanleitung

Panasonic

Panasonic EY46A5 Bedienungsanleitung

Panasonic

Panasonic EY46A5 Bedienungsanleitung

Panasonic

Panasonic EY3610 Bedienungsanleitung

Panasonic

Panasonic EY3640 Bedienungsanleitung

Panasonic

Panasonic EY75A8 Bedienungsanleitung

Panasonic

Panasonic EY4541X57 Bedienungsanleitung

Panasonic

Panasonic AccuPulse QP Low Noise Series Bedienungsanleitung

Panasonic

Panasonic 7552LJ Bedienungsanleitung

Panasonic

Panasonic EY7550LR2S Bedienungsanleitung

Panasonic

Panasonic EY4550 Bedienungsanleitung

Panasonic

Panasonic EYFLA4 Bedienungsanleitung

Beliebte Elektrowerkzeuge Handbücher anderer Marken

AEG

AEG OMNI-JS Bedienungsanleitung

SIP

SIP 01533 Bedienungsanleitung

Ribimex

Ribimex PRS499 Bedienungsanleitung

3M Fiber Optic Connector Crimp Tool Bedienungsanleitung

Ryobi

Ryobi P524 Bedienungsanleitung

ROJEK

ROJEK FSN 300A Bedienungsanleitung

WABCO

WABCO OptiTire Bedienungsanleitung

EINHELL

EINHELL TE-MS 18/210 Li Bedienungsanleitung

Orgapack

Orgapack OR-T 85 Kurzanleitung

TOUGHCUT

TOUGHCUT Diamond 400 Bedienungsanleitung

Yaros

Yaros PB-3603 Bedienungsanleitung

Fein

Fein BSS 2.0 E Einrichtungshandbuch

Baileigh Industrial

Baileigh Industrial SS-2725 Bedienungsanleitung

Milwaukee

Milwaukee 2674-20 Bedienungsanleitung

Fein

Fein BLs 1.6 Bedienungsanleitung

Princess

Princess Electric Multi Sharpener Bedienungsanleitung

FOREDOM

FOREDOM K.1050 Handbuch

Silca

Silca MARKER 2000 Bedienungsanleitung