Panasonic ET-PKL100H Bedienungsanleitung

ENGLISH

Installation Instructions

Ceiling Mount Bracket (for High Ceilings)

Thank you for purchasing this Panasonic Product.

JTo customers

The “Installation Instructions” is intended for use by installation personnel. Be sure to employ certied

personnel to perform the installation. After installation, have the installation personnel return these “Installation

Instructions” to you, and save it for future use. When moving or removing the projector, give this “Installation

Instructions” to the installation personnel and have them perform the procedure.

JTo installation personnel

Carefully read the “Installation Instructions” and install this product correctly and safely.

Be sure to read through the section entitled “Read this rst!” (page 3) before proceeding with the installation.

After installation, return these “Installation Instructions” to the customer.

TQZJ606-2

Model No.

ET-PKL100H

2 - ENGLISH

Contents

Read this rst! ................................................................................................... 3

Product description........................................................................................... 4

Installation.......................................................................................................... 6

Setting up the screen.......................................................................................................... 6

Screws tightening torques .................................................................................................. 6

Mounting the attachment plate to the ceiling ...................................................................... 6

Adjustment pole preparation............................................................................................... 8

Installing the adjustment poles to the attachment plate ..................................................... 9

Installing the brackets to the projector.............................................................................. 10

Suspending the projector.................................................................................................. 10

Adjusting the installation angle ..................................................................... 11

Installation of ceiling mount bracket drop-prevention kit ........................... 12

Specications .................................................................................................. 13

ENGLISH - 3

Read this rst!

CAUTION:

Only install a designated projector.

Only install using a designated method.

zThe projector may fall down and be damaged, and an injury may result.

Do not install the unit in a location that may impede projector ventilation.

zA re may result.

Do not hang from or hang objects on the projector or ceiling mount bracket.

zThe projector may fall and cause injury.

When installing, always use the supplied components.

zThe unit may be damaged, or the projector may fall down and an injury may result.

Install the mounting screws and power cable in such a way that they will not make contact with metal

objects inside the ceiling.

zElectric shocks may result from contact with any metal objects inside the ceiling.

Always follow these precautions

WARNING:

Installation work should only be carried out by the certied personnel.

zIf this product is not installed correctly, serious accidents may result.

zFollow the instructions specied in “Installation” and "Installation of ceiling mount bracket drop-prevention

kit" of this manual, and perform secure installation.

Install the ceiling mount bracket in accordance with the structure and materials of the installation

location.

zIf a mistake is made in the installation procedure, the ceiling mount bracket may fall down and an injury may

result.

Mounting and installation must be carried out by two or more persons.

zWhen installing the projector in an overhead location, for example, in a high ceiling, at least two persons will

be required to handle the installation.

Make sure that your footing is safe and secure during installation.

zIf your footing is not secure, you may fall down or drop the unit, and an injury may result.

Do not loosen or remove the unit screws and bolts unnecessarily.

zThe projector may fall down and an injury may result.

Do not install in a location that is not strong enough.

zIf the installation location is not strong enough, the unit may fall down and damage to the projector or an

injury may result.

Do not install the ceiling mount bracket in humid or dusty locations or in locations where the ceiling

mount bracket may come into contact with oily smoke or steam.

zUsing the projector under such conditions may result in re or electric shock. Also, the oil will cause the

plastic to deteriorate and the projector may fall down when installed on a ceiling.

Do not allow children to reach the supplied screws and metal ttings.

zThe supplied screws and metal ttings can cause personal injury if swallowed.

zIf swallowed, seek medical advice immediately.

Do not disassemble or modify the ceiling mount bracket.

zThe projector may be damaged or fall, causing injury.

rPanasonic Connect Co., Ltd. takes no responsibility for any accident or damage caused by the

installation of the ceiling mount bracket using methods that are not described or methods that do

not use the parts specied in these Installation Instructions.

rIf products are no longer being used, they should be dismantled and removed by certied personnel

as soon as possible.

4 - ENGLISH

Product description

This is a ceiling mount bracket for installing projectors.

■Applicable ceiling mount brackets

ET-PKL420B / ET-PKL430B

■Structural components

Parts name Form (number of parts) Applications

Attachment plate × 1

The attachment plate is attached

to the ceiling via four ceiling mount

bolts. Installation methods are dif-

ferent for concrete and wooden ceil-

ings. It also allows horizontal swing

adjustment.

Adjustment poles ×1 × 1

These are adjustment poles which

are installed in between the attach-

ment plate and the projector mount

bracket (sold separately).

They also include a function for

adjusting the distance between the

ceiling and the projector.

Angle adjusting

bracket

× 1

This attaches to the projector mount

bracket.

It also includes a function for adjust-

ing the forward/backward tilt.

Angle adjusting

bracket

× 1 This is installed to adjustment pole

Screws and bolts

Hex head bolt, captive washer (M6×16)

These are used to assemble the

bracket and mount onto the projec-

tor mount bracket.

× 19

• The M6 indications in the installation instructions refer to the captive washer hex head bolt.

ENGLISH - 5

■The user must also obtain the following parts. (sold separately)

Installation work Required parts page

Installing the attach-

ment plate to the

ceiling

Installing to a

wooden structure

Ceiling mount bolt (×4), Hex nut (×16), Spring washer (×8)

Flat washer (×16) 7

Installing to a

concrete structure

Ceiling mount bolt (× 4), Hex nut (× 12), Spring washer (× 8),

Flat washer (× 12), Anchoring nut or curled plug (× 4) 7

Installation of ceiling

mount bracket drop-

prevention kit

Installing to a

wooden structure

Ceiling mount bolt (× 1), Hex nut (× 2), Flat washer (× 1),

Spring washer (× 1) 12

Installing to a

concrete structure

Anchoring nut or curled plug (x1),

Spring washer (x1), Hex head bolt (x1) 12

• Be sure to use M8 or 5/16"suspension bolts, nuts, at washers, spring washers and anchor nuts.

zStore small parts in an appropriate manner, and keep them away from young children.

zScrew tightening torques: M6: 4 ± 0.5 N

•

m, M8 or 5/16": 10 ± 1 N

•

zUse a torque screwdriver or torque wrench when tightening the bolts and nuts. Do not use electric screwdrivers

or impact screwdrivers.

Attention

zDispose of the packaging materials properly after taking the product out of it.

Product description (continued)

6 - ENGLISH

Installation

After checking the height, width and structure of the installation location, determine the appropriate positions for

setting up the screen and installing the projector.

Setting up the screen

Set up the screen according to the specied method in a position which takes into account the projection distance

and angle and the type of screen being used.

Screws tightening torques

M6…………………4 ± 0.5 N • m

M8 or 5/16"…………10 ± 1 N • m

zWhen tightening the screws, use a torque screwdriver or a hex torque wrench to tighten the screws to the

specied tightening torques. Do not use electric screwdrivers or impact screwdrivers.

Mounting the attachment plate to the ceiling

After checking the height, width, and structure of the installation location, determine the appropriate positions for

setting up the screen and installing the projector. Determine the location of the attachment plate in the ceiling to

align the lens with the center of the screen.Ø

■Attachment plate mounting hole sizes and preparation

Make mounting holes while referring to the following diagrams.

100(3-15/16''))

106(4-3/16'')

132(5-3/16'')

150(5-29/32'')

116(4-9/16'')

142(5-19/32'')

160(6-5/16'')

66(2-19/32'')

71(2-25/32'')

4 - φ11.5 (7/16'')

110(4-11/32'') 142(5-19/32'')

132(5-3/16'')

Unit:mm('')

Install the attachment plate so that the

arrow points toward the screen.

(Dimensions from below)

To the

screen

Four holes drilled to fit M8 bolts

Attention

zIf installing to a concrete structure, the sizes of the bolt mounting holes should match the sizes of the anchoring

nuts or curled plugs used.

zPlease purchase M8 or 5/16" bolt for the commercially available ceiling mount bolt, hex nut, at washer, spring

washer, anchoring nut or curled plug.

ENGLISH - 7

Installation (continued)

■Installing the attachment plate

Depending on whether it is installed on a concrete or wooden ceiling structure, there are two different installation

methods. Carry out by the appropriate installation method which is suited to each ceiling.

zInstalling to a wooden structure

Ceiling mount bolt

(M8 or 5/16")

Spring washer

Attachment plate

To the screen

Flat washer

Hex nut

Ceiling surface

Hex nut

Flat washer

Approx. 5 mm(3/16˝)

Suspension bolt stay

(beam side)

1 Make holes in the ceiling surface for inserting the ceil-

ing mount bolts.

zThe sizes of the holes in the ceiling should match

the sizes of the mounting holes in the attachment

plate. (Refer to page 6 for attachment positions.)

2 Secure the ceiling mount bolts.

zCheck that the ceiling mount bolt locations are

strong enough to bear the full weight of the projec-

tor. If they are not strong enough, use reinforce-

ments while giving full consideration to the required

safety coefcient.

3 Secure the attachment plate to the ceiling mount bolts.

zIn the side of the attachment plate, the end of the

ceiling mount bolts should protrude from the hex

nuts by about 5 mm. Be sure to use the commercial-

ly available at washers and spring washers when

installing the attachment plate.

Attention

z Make sure the arrow displayed in the attachment

plate points toward the screen while attaching.

Attention

zUse only size M8 or 5/16"ceiling mount bolts, hex nuts, washers and spring washers.

zAll bolts and nuts should be securely tightened, and sufcient measures such as us-

ing two nuts or painting should be employed as necessary to prevent any loosening.

zInstalling to a concrete structure

Anchoring nut or curled plug

Concrete

Flat washer

Spring washer

Hex nut

Ceiling mount bolt

(M8 or 5/16")

Spring washer

Attachment plate

To the screen Hex nut

Ceiling surface

Flat washer

Approx. 5 mm (3/16˝)

1 Attach the anchoring nuts or curled plugs to a concrete

ceiling and securely x the four ceiling mount bolts.

(Refer to page 6 for attachment positions.)

zWhen installing the anchoring nuts or curled plugs,

adhere strictly to the installation instructions supplied

by the manufacturer of the nuts, so they will

not loosen in the concrete structure or be dislodged

from the intended positions.

zCheck to make sure that the concrete ceiling struc-

ture can easily bear the whole weight of the projector

and the ceiling mount bracket.

If it is found to be fragile or degraded, use steel or

wooden reinforcements.

2 Secure the attachment plate to the ceiling mount bolts.

zIn the side of the attachment plate, the ends of the

ceiling mount bolts should protrude from the hex nuts

by about 5 mm. Be sure to use the commercially

available at washers and spring washers when

installing the attachment plate.

Attention

zMake sure the arrow displayed in the attachment plate

points toward the screen while attachment.

Two nuts

8 - ENGLISH

Installation (continued)

Adjustment pole preparation

Install adjustment pole Ato adjustment pole Band to angle adjusting bracket B by following the procedure

below.

Arrow

FRONTinscription

Fully tighten the captive

washer hex head bolts

at the front and back.

Angle adjusting

bracket

Provisionally tighten the

bolts at the left and right.

Adjustment pole

1 Use the 4 supplied captive washer hex head bolts

to secure the angle adjusting bracket Bto the

adjustment pole B as shown in the illustration on

the left.

Attention

zTemporarily tighten the captive washer hex head

bolts at left and right.

zAlign the FRONT inscription on the adjustment

pole B with the arrow on the angle adjusting

bracket B.

Adjustment pole

Provisionally tighten the

captive washer hex

head bolt (x 6)

2 Insert the adjustment pole Binto the adjustment

pole Aso that the holes are aligned, and then

use the 6 supplied captive washer hex head bolts

to temporarily secure them.

Attention

zThe adjustment poles Aand Bare both pro-

vided with holes which are spaced at 20-mm

intervals.

Temporarily secure the poles together so that the

hole positions match the height obtained from

the standard installation dimensions which are

described in the installation instructions of the

projector mount bracket.

zAlign the FRONT inscription on the adjustment

pole A with the FRONT inscription on the

adjustment pole B.

3 Securely tighten the 2 captive washer hex head

bolts at the front which were temporarily tightened

in step 2.

4 Securely tighten the remaining 4 captive washer

hex head bolts at the rear which were temporarily

tightened in step 2.

Attention

zBe sure to secure the adjustment poles Aand

Bat all six points.

ENGLISH - 9

Installation (continued)

Installing the adjustment poles to the attachment plate

Follow the procedure given below to install the adjustment poles to the attachment plate which has been installed

to the ceiling.

Ⓐ

FRONT

Arrow

Attachment plate

inscription

Adjustment pole

1 Notice the shape of the protrusion on the adjustment

pole A, insert it into the center hole of the attachment

plate, and then rotate the adjustment pole A, so that

the FRONT inscription on the adjustment pole Ais

aligned with the arrow on the attachment plate.

Attention

zHold the adjustment pole A rmly until inserting the

adjustment pole Ainto the hole of the attachment

plate and the rotating the adjustment pole Aare

nished.

Ⓐ

Adjustment pole

FRONTinscription

Attachment plate

Arrow

Provisionally tighten

in 3 places.

2 Overlap the 3 screw holes on the adjustment pole A

with the 3 slots in the attachment plate, and then use

the 3 supplied captive washer hex head bolts to tem-

porarily secure them.

10 - ENGLISH

Installing the brackets to the projector

After installing the projector mount bracket (sold separately) to the projector, install the angle adjusting bracket A

by following the procedure below.

As shown in the gure on the left, temporarily se-

cure the angle adjusting bracket Ato the projector

mount bracket with the 4 supplied captive washer

hex head bolts.

Note

zThe illustrations for the projector and the pro-

jector mount bracket may be different from real

products.

Suspending the projector

Angle adjusting bracket B

Hooks

Angle adjusting bracket A

1 Fit the hook of angle adjusting bracket Aon the

captive washer hex head bolts which are tempo-

rarily tightened in step 1 on page 8.

Attention

zDo not remove your hands from the projector

until the captive washer hex head bolts of angle

adjusting bracket B are rmly hooked into the

L-shaped grooves.

WARNING

■Mounting and installation must be

carried out by two or more persons.

Temporarily secure

in 2 places

Angle adjusting bracket B

Angle adjusting bracket A

2 Temporarily secure angle adjusting brackets A

and B with the 2 supplied captive w-asher hex

head bolts as shown in the illustration on the left.

Attention

zMake sure that the projector is horizontal when

temporarily tightening the xing captive washer

hex head bolts.

Projector mount

bracket

Angle adjusting bracket A

Temporarily

secure in 4

places.

Installation (continued)

Inhaltsverzeichnis

Andere Panasonic Rack & Stand Handbücher

Panasonic

Panasonic WV-Q201 Bedienungsanleitung

Panasonic

Panasonic WV-Q122A Bedienungsanleitung

Panasonic

Panasonic TY-ST42PX5W Bedienungsanleitung

Panasonic

Panasonic WV-Q204/1S Bedienungsanleitung

Panasonic

Panasonic TY27G22M - TV STAND Bedienungsanleitung

Panasonic

Panasonic CWFE14CM Bedienungsanleitung

Panasonic

Panasonic TY-ST43PE8 Bedienungsanleitung

Panasonic

Panasonic TY-ST32L7-S Bedienungsanleitung

Panasonic

Panasonic TY34WDM60J - STAND FOR CT34WDM60 Bedienungsanleitung

Panasonic

Panasonic TY-ST65PV500 Bedienungsanleitung

Panasonic

Panasonic WV-Q204/1S Bedienungsanleitung

Panasonic

Panasonic TC349815 Bedienungsanleitung

Panasonic

Panasonic TY32G22M - TV STAND Bedienungsanleitung

Panasonic

Panasonic TY-ST20-K Bedienungsanleitung

Panasonic

Panasonic WV-Q174 Bedienungsanleitung

Panasonic

Panasonic KXTCA817EX Bedienungsanleitung

Panasonic

Panasonic TY-CE103PS10 Bedienungsanleitung

Panasonic

Panasonic TY-S37PX60W Bedienungsanleitung

Panasonic

Panasonic ET-JPF200BU Bedienungsanleitung

Panasonic

Panasonic TYST65R2WG - Stand For Plasma Panel Bedienungsanleitung

Panasonic

Panasonic TY-ST42D1-WG Bedienungsanleitung

Panasonic

Panasonic WV-Q126 Bedienungsanleitung

Panasonic

Panasonic TY-ST65P11-K Bedienungsanleitung

Panasonic

Panasonic TY-WK65PR20 Bedienungsanleitung

Beliebte Rack & Stand Handbücher anderer Marken

Salamander

Salamander Acadia AC/W/L400/WH Bedienungsanleitung

Fohhn

Fohhn VAT-09 Benutzerhandbuch

ricoo

ricoo FS0522 Bedienungsanleitung

AMSOIL

AMSOIL BMK-22 Kurzanleitung

Kargo Master

Kargo Master 48220 Bedienungsanleitung

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Bedienungsanleitung

ricoo

ricoo S1222 Bedienungsanleitung

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Bedienungsanleitung

VidaBox

VidaBox VB MNT FFS2 Bedienungsanleitung

Welch Allyn

Welch Allyn 48960 Bedienungsanleitung

Arkon

Arkon CM035-ST-2 Bedienungsanleitung

PROEL

PROEL PLWIN60C Bedienungsanleitung

Agilent Technologies

Agilent Technologies E2609B Bedienungsanleitung

Mustang

Mustang MV-ARM4 Bedienungsanleitung

Mounting Solutions

Mounting Solutions WRM-320 Bedienungsanleitung

Pyle

Pyle PMKSPAD1 Bedienungsanleitung

ShelterIt

ShelterIt 21208 Bedienungsanleitung

SPL

SPL RackPack?4 1040 Bedienungsanleitung