Panasonic WJHD309 - DIGITAL DISK RECORDER Bedienungsanleitung

Digital Disk Recorder

WJ-HD300 series S-ATA conversion guide

WJ-HD309, WJ-HD316,WJ-HD309A,WJ-HD316A

1. Sept. 2008

Panasonic System Solutions

Panasonic System Solutions HD300_SATAConversionGuide_B

WJ-HD300 S-ATA conversion guide Maintenance guide

1. Introduction

This manual describes how to convert the hard disk drive installed in the WJ-HD300 series from the P-ATA type to the S-ATA type.

Applicable models: WJ-HD309, WJ-HD316, WJ-HD309A, WJ-HD316A

2. Preparation

(1) Screwdriver

(2) S-ATA conversion kit (part number: 0E0A0027AA)

Part name Part number Quantity

S-ATA Board Ass’y JH30AJKY6A 1

S-ATA cable K1V322Y20001 1

S-ATA angle 3CA005877AAA 1

S-ATA label, small (for front, 2pcs) 3PD003840AAA 1

S-ATA label, large (for top) 3PD003841AAA 1

S-ATA leaet 3TU001942AAA 1

(3) S-ATA HDD (250GB) x 2 (part number: HDATW250GASY)

3. Replacement Procedure

Important +++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++

• Do not detach the cable connecting the unit and the front panel while the HDD status indicators are still lit or until 30 seconds have passed

since the HDD status indicators went off.

• Protect the hard disk drives from static electricity.

• Do not stack them, or keep them upright.

• Do not use an electric screwdriver to x them. (Tightening torque: Approx. 0.49 N · m (5 kgf · cm))

• Avoid rapid changes in the temperature/humidity to prevent condensation. (Acceptable change: within 15°C/h (59 °F/h))

+++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++

(1) Open the connectors cover on the front panel, and remove

the screw.

Then, remove the front panel by sliding it to the left.

Screw

Connectors cover

Panasonic System Solutions HD300_SATAConversionGuide_B

WJ-HD300 S-ATA conversion guide Maintenance guide

(2) Disconnect the connector from the front panel.

(3) Remove four screws that x the HDD mounting unit, and

then pull the HDD unit toward you by holding the tabs of

the angle.

(4) Remove four screws xing the upper HDD.

Disconnect the IDE connector and power connector from

the HDD, and remove the HDD from the HDD mounting

angle.

Caution++++++++++++++++++++++++++++++++++++

When removing the screws, hold the HDD by hand to prevent

it from falling and being impacted.

+++++++++++++++++++++++++++++++++++++++++++

Front panel

connector

SSD

Screws

Hold these

tabs and pull

SSD

Pull-ring

Jumper pin

Screws for the upper

hard disk drive

(4 screws: 2 screws each

on the both sides)

Hard disk drive mounting angle

Flat cable

Power supply

cable

Panasonic System Solutions HD300_SATAConversionGuide_B

WJ-HD300 S-ATA conversion guide Maintenance guide

(5) To remove the lower HDD, disconnect the power

connector from the ATA board.

Then, remove the screw A; one of the three screws xing

the ATA board.

(6) Remove four screws xing the lower HDD.

Disconnect the connectors from the HDD, and remove the

HDD from the HDD mounting angle.

Caution++++++++++++++++++++++++++++++++++++

When removing the screws, hold the HDD by hand to prevent

it from falling and being impacted.

+++++++++++++++++++++++++++++++++++++++++++

(7) Disconnect the IDE cable from the ATA board.

(8) Remove the two other screws xing the ATA board, and

then remove the ATA board.

(9) Remove two screws xing the ATA angle, and then

remove the ATA angle.

(10) Install new S-ATA angle on the HDD mounting angle with

the two screws removed in step (9).

SSD

Hard disk drive mounting angle

Screws for the lower hard disk drive

(4 screws: 2 screws each

on the both sides)

Screw removed from

point A

Connector of the

power supply cable

Screw removed from point A

Screw A

ATA Board

ATA board screws

(2 screws)

Angle screws

HDD mounting angle

Panasonic System Solutions HD300_SATAConversionGuide_B

WJ-HD300 S-ATA conversion guide Maintenance guide

(11) Install the S-ATA board on the S-ATA angle with the three

screws removed in step (5) and step(8).

(12) Install two S-ATA HDDs in the HDD mounting angle with

four screws each.

Note: No jumper is provided on the S-ATA HDD.

Install the HDD so that the board side faces down and the

connector side faces the S-ATA board.

(13) Connect the S-ATA cables and the power cable to the

S-ATA board and the HDDs as shown right. Make sure

that the connectors have been inserted completely.

HDD mounting angle

SATA board

screws (3screws)

SATA board

Screw A

Twist the power supply

cable 360° and insert

For HDD2 (Gray)

For HDD1 (Red)

CN301

CN302

For power supply

CN305

To prevent the

cables from

banking, pass the

gray cable under

the red cable.

Panasonic System Solutions HD300_SATAConversionGuide_B

WJ-HD300 S-ATA conversion guide Maintenance guide

(14) Install the HDD mounting unit with the four screws removed in step (3) in the reverse order of removal.

Caution ++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++

•When installing the HDD mounting unit, remove dust around the connector that connects the HDD mounting unit the and the main unit.

Adhesion of dust may cause a trouble.

•Insert the connectors and screws rmly.

++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++

(15) Attach the S-ATA label, small (for front) to the front

chassis.

(16) Connect the connector to the front panel, and install the

front panel with the screw remove in step (1) and close the

connectors cover.

Approx.

3mm

Approx.

3mm

SATA label(for front)

Conﬁrm that the power supply

cable and the HDD cable do

not touch the front chassis.

Panasonic System Solutions HD300_SATAConversionGuide_B

WJ-HD300 S-ATA conversion guide Maintenance guide

(17) Attach the S-ATA label, large (for top) to the top panel.

Attach the S-ATA label, small (for front) to the connectors

cover.

Note:

The new HDDs need to be formatted before operation. Refer to the Operating Instructions for detail.

+++++++++++++++++++++++++++++++++++++End of the document+++++++++++++++++++++++++++++++++

PAN/TILT

RECSTOP

PULL

/AUTO

ZOOM/

A-B

LAST

/ESC

DigitalDiskRecorder

WJ-HD

FWDREV

BUSY

SET

SETUP

SLOW

LISTED

REPEAT

GOTO

PRESET

IRIS

FOCUS

PAN/TILT

13 14 15 16

1211

10/0

5 6 7 8

4321

LOGOUT

MARK

OSD

SEQ

TEXT

COPY

EL-ZOOM

SHIFT

MONITOR1

MONITOR2

ALARM

RESET

HDD2

HDD1

TIMER

ERROR

ALARM

SUSPEND

OPERATE

DISKSELECT

S-ATA

7-10mm

Approx. 2mm

3-5mm

Approx. 17mm

SATA label(for top)

SATA label(for front)

Andere Handbücher für WJHD309 - DIGITAL DISK RECORDER

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Panasonic Aufnahmegeräte Handbücher

Panasonic

Panasonic AK-MSU935AP Bedienungsanleitung

Panasonic

Panasonic AJHD1400 - DVCPRO HD VTR Bedienungsanleitung

Panasonic

Panasonic DVCPRO P2 Series Bedienungsanleitung

Panasonic

Panasonic AV-HLC100E Bedienungsanleitung

Panasonic

Panasonic 302 Bedienungsanleitung

Panasonic

Panasonic RR-XS410 Bedienungsanleitung

Panasonic

Panasonic SZ-CB8 Bedienungsanleitung

Panasonic

Panasonic NV-HD610EG Bedienungsanleitung

Panasonic

Panasonic WJHD309A - DIGITAL DISK RECORDER Bedienungsanleitung

Panasonic

Panasonic AJ-PD500P Bedienungsanleitung

Panasonic

Panasonic PN28080i-ID Bedienungsanleitung

Panasonic

Panasonic CA-LSR10U - Sirius Satellite Radio Receiver Bedienungsanleitung

Panasonic

Panasonic WJ-NV300K Bedienungsanleitung

Panasonic

Panasonic WJHD200 - Digital Disk Recorder Bedienungsanleitung

Panasonic

Panasonic SJ-MR230DGH Bedienungsanleitung

Panasonic

Panasonic SLPR300 - CD RECORDER Bedienungsanleitung

Panasonic

Panasonic P2HD AG-HPG20 Bedienungsanleitung

Panasonic

Panasonic AJ-HPM110 Bedienungsanleitung

Panasonic

Panasonic SVSR100 - SD AUDIO RECORDER Bedienungsanleitung

Panasonic

Panasonic AJLT85P - DVC PRO Bedienungsanleitung

Panasonic

Panasonic ET-YFB100G Bedienungsanleitung

Panasonic

Panasonic WJND200 - NETWORK DISK RECORDER Bedienungsanleitung

Panasonic

Panasonic AGHPG10 - MEMORY CARD PORTABLE RECORDER Bedienungsanleitung

Panasonic

Panasonic AG-HPD24P Bedienungsanleitung

Beliebte Aufnahmegeräte Handbücher anderer Marken

KV2 Audio

KV2 Audio 500 Series Bedienungsanleitung

Robotics Technologies

Robotics Technologies microBus-Cam II Bedienungsanleitung

Seca

Seca 460 Bedienungsanleitung

Cognex

Cognex MVS-8000 Series Bedienungsanleitung

Mect

Mect MPNC006 Series Bedienungsanleitung

Bad Caf

Bad Caf THE LEASH Bedienungsanleitung

Strymon

Strymon NIGHTSKY Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric 16CH DIGITAL RECORDER DX-TL5000U Bedienungsanleitung

Tews Technologies

Tews Technologies TPMC465 Bedienungsanleitung

Honeywell

Honeywell Excel 50 Bedienungsanleitung

SeaLevel

SeaLevel COMM+8.LPCI Bedienungsanleitung

Arturia

Arturia AUDIOFUSE STUDIO Bedienungsanleitung

Rukra

Rukra RK-1240 Bedienungsanleitung

Samson

Samson SCOM Bedienungsanleitung

Dynacord

Dynacord DPS260 Bedienungsanleitung

Pyle Pro

Pyle Pro PSS8 Bedienungsanleitung

Nice

Nice Core Bedienungsanleitung

RF-System

RF-System TinyGate Gebrauchs- und Pflegehandbuch