Panasonic CZ-RTC5 Bedienungsanleitung
Panasonic Corporation
1006 Kadoma, Kadoma City, Osaka, Japan
Operating Instructions
High-spec Wired Remote Controller
Model No. CZ-RTC5
Installation Instructions
Separately Attached.
ENGLISH
Before operating the unit, read these operating instructions thoroughly and keep them for future
reference.
CV6233312187
Panasonic Corporation
http://www.panasonic.com
2(EN)
Safety Precautions
CAUTIONS
This appliance is intended to be used by expert or
trained users in shops, in light industry and on farms, or
for commercial use by lay persons.
This appliance can be used by children aged from 8
years and above and persons with reduced physical,
sensory or mental capabilities or lack of experience
and knowledge if they have been given supervision or
instruction concerning use of the appliance in a safe
way and understand the hazards involved.
WARNING
Do not use this appliance in a potentially explosive
atmosphere.
• Do not operate with wet hands.
• Do not wash with water.
In case of malfunction of this appliance, do not repair by
yourself. Contact the sales or service dealer for repair.
In case of emergency, remove the power plug
from the socket or switch off the circuit breaker
or the means by which the system is isolated
from the mains power.
WARNING CAUTION
This symbol refers to a hazard or unsafe
practice which can result in severe personal
injury or death.
This symbol refers to a hazard or unsafe
practice which can result in personal injury or
product or property damage.
Matters to be observed Prohibited matters
3
(EN)
Note:
zThis device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1) This
device may not cause harmful interference, and (2) this
device must accept any interference received, including
interference that may cause undesired operation.
zThis equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause
harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more
of the following measures:
• Reorient or relocate the receiving antenna.
•
Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician
for help.
zFCC Caution: To assure continued compliance, follow
the attached installation instructions. Any changes
or modiÞcations not expressly approved by the party
responsible for compliance could void the user’s authority
to operate this equipment.
4(EN)
Preparations
How to Use Setting Change When
Necessary
Page
Thank you for purchasing the
Panasonic high-spec wired remote
controller.
zRead the Operating Instructions
carefully for safe use. This
manual describes the Operating
Instructions of the wired remote
controller. Read this manual as
well as operating instructions
supplied with indoor units and
outdoor units.
zBe sure to read the “Safety
Precautions” (P.2, 3) before
using.
zKeep this manual with operating
instructions supplied with indoor
units and outdoor units in a safe
place.
zBe sure to keep this manual in a
place easily accessible by users.
In the case of user change, be
sure to give this manual to the
new user.
NOTICE
The English text is the original
instructions. Other languages
are translation of the original
instructions.
CONTENTS
zSafety Precautions...............................2
zPart Names ..........................................5
• Control panel .......................................5
• Screen display .....................................6
zBasic Operations..................................8
zMenu List ............................................10
zFlap Setting for Each Indoor Unit ....12
• FLAP..................................................12
zFlap Setting for Each Air Outlet .......13
• Lock indiv. ßap ...................................13
zTimer Reservation .............................14
• ON/OFF timer ....................................14
• Weekly timer overview.......................15
• Weekly timer ......................................16
zFilter Information................................20
zQuiet Operation/
Power Consumption Monitor............22
zEnergy Saving ....................................24
• ECONAVI...........................................24
• Temp auto return................................26
• Temp range........................................27
• Auto shutoff........................................28
• Schedule peak cut .............................30
• Repeat off timer .................................32
zOuting Function .................................33
zInitial Settings ....................................35
• Clock/Clock type/Operation lock........35
• Controller name .................................36
• Touch sound/Contrast/Backlight/
Language ..........................................37
•
Password change/Temp sensor/
Main/sub/Vent output/Contact address
...38
zVentilation Setting..............................40
zSetting List..........................................41
zTroubleshooting .................................43
zSpeciÞcations.....................................45
5
(EN)
Part Names Control panel
Note
LCD screen
Return button
Returns to the previous screen.
Menu button
Displays the menu
screen (P. 10).
Operation indicator
Illuminates during operation.
Blinks during alarm.
Start/Stop button
Starts/Stops operation.
Enter button
Fixes the selected content.
Press centre No glove No pen
Energy saving
button
Switches Energy
saving/Normal
operation.
Cross key buttons
Selects an item.
Up
Down
RightLeft
6(EN)
When inspection is
required (P.43)
Appears if there is a
problem on ECONAVI.
Top screen
Operation stop
screen
Item selection
screen
Lock screen display
Remote controller
name (P.36)
Operation is
locked. (P.35)
Present time &
day (P.35)
Setting
information
icon
When
checking the
meanings
of all icons
(P.41)
Operation guide (P.7)Cursor
Operation
mode
Set temperature Fan speed Flap
[Operation lock] is functioning.
(P.35)
zTo cancel lock
Press button for
4 seconds.
The indoor unit is stopped or slight blow operation is in process.
Part Names Screen display
Appears when
ECONAVI is
being set to
ON.
7
(EN)
Menu screen (P.10)
Screen name Present time & day
The currently operable content is simply
displayed.
• ŸźŻŹ: Cross key buttons
• : Enter button
Icon Description Page
The indoor unit Þlter needs to be cleaned. P.20
The engine oil needs to be replaced.
(Only when using a gas heat pump air conditioner.) -
Switching operation modes is prohibited.
(Switching to Auto mode is also prohibited.) -
Remote control operation is restricted by a central control device. -
[ON/OFF timer] is set. P.14
[Weekly timer] is set. P.15
Energy saving operation is in process. P.8
Fresh air is used for ventilation.
(Only when connecting a heat exchange ventilation unit or
connecting a commercially sold fan.)
P.40
Prevents the room temperature from increasing too much (or
decreasing too much) when no one is in the room. P.33
Setting information icons displayed on the top screen
Operation guide
8(EN)
Basic Operations
1Start operation.
Press .
(The operation indicator illuminates.)
To change the setting
(P.10)
To turn the energy saving
operation ON/OFF
Press during operation.
(Only for models equipped with the
energy saving function.)
To stop
(The operation indicator turns off.)
2Select the item to set.
Press ŻŹ.
3Change the setting.
Press Ÿź ĺ.
(The cursor disappears.)
Energy saving operation
is in process.
Operation indicator
Note
zOperation modes that cannot be set are not displayed.
zThe ßap display differs from the actual ßap angle.
zPressing after recovery from mains power failure will resume operation with
the contents before mains power failure has occurred.
zIf no operation is performed for a certain period of time, the backlight turns off to
save electricity. (Press any button for illumination.)
zThe energy saving operation restricts the maximum current value, resulting in
decreased cooling/heating performance.
(If the current of outdoor units does not reach the peak due to low load operation,
the current value is not restricted.)
zThe temperature range that can be set varies depending on the model.
zThe set temperature range can be changed using the remote controller. (P.26)zSome models do not display the ßap.
9
(EN)
Perform the following operations in step 2 on page 8.
Operation mode (e.g. Cool, Heat, etc.)
Press Ż.
*Auto:
The mode is
automatically
switched to
Cool or Heat to
achieve the set
temperature.
Ļ
Heat
Dry
Cool
Fan
Auto
Set temperature
Press .(When the cursor is not
visible)
• Cool/Dry: 18 °C to 30 °C
• Heat : 16 °C to 30 °C
• Auto : 17 °C to 27 °C
Fan speed
Press Ź.
Flap
Press Ź2 times.
Flap Setting for Each Indoor
Unit (P.12)
• : Swing
• Pressing Ÿź
during swing can
stop the ßap at your
preferred position.
• 5-level adjustment
is possible
during Heat,
Fan and Auto
(Heat) modes.
Cursor
*Auto:
Cannot be
selected in
Fan mode.
Ļ
High
Medium
Low
Auto
10 (EN)
1Display the menu screen.
To return to the previous screen
Press .
When no operation is performed
in each setting screen for several
minutes
The display returns to the top screen.
2Select the menu item.
Ÿźĺ
To turn the page
Press ŻŹ.
Selectable menus (1 to 13)
For details of screen examples,
see the next page.
Menu List
Andere Handbücher für CZ-RTC5
1
Inhaltsverzeichnis
Andere Panasonic Fernbedienung Handbücher
Panasonic
Panasonic CZ-RD513C Installations- und Betriebshandbuch
Panasonic
Panasonic CZ-RTC4 Bedienungsanleitung
Panasonic
Panasonic TX-28DT4 Bedienungsanleitung
Panasonic
Panasonic AK-HRP1005G Bedienungsanleitung
Panasonic
Panasonic AK-HRP200G Bedienungsanleitung
Panasonic
Panasonic CZ-RD514C Installations- und Betriebshandbuch
Panasonic
Panasonic PVCC50 - COLOR CORRECTOR Bedienungsanleitung
Panasonic
Panasonic EUR7622KB0 Bedienungsanleitung
Panasonic
Panasonic EUR511151 Bedienungsanleitung
Panasonic
Panasonic WV-CB550 Bedienungsanleitung
Panasonic
Panasonic CZ-RTC2 Bedienungsanleitung
Panasonic
Panasonic AK-HRP1000G Bedienungsanleitung
Panasonic
Panasonic TNQ2AE013 Bedienungsanleitung
Panasonic
Panasonic EUR511112 Bedienungsanleitung
Panasonic
Panasonic CZ-RTC5A Bedienungsanleitung
Panasonic
Panasonic CZ-RC515UA Betriebsanleitung
Panasonic
Panasonic AW-RP50 Bedienungsanleitung
Panasonic
Panasonic CZ-RWSD2U Bedienungsanleitung
Panasonic
Panasonic CZ-RTC4A Bedienungsanleitung
Panasonic
Panasonic WVCU360C - SYSTEM CONTROLLER Bedienungsanleitung
Beliebte Fernbedienung Handbücher anderer Marken
Bang & Olufsen
Bang & Olufsen Beo4 Bedienungsanleitung
Sunwave Tech.
Sunwave Tech. RemoteComm SRC-7000 Bedienungsanleitung
Multiplex
Multiplex PROFI TX 9 Bedienungsanleitung
One Remote
One Remote RMB4 Bedienungsanleitung
FUTABA
FUTABA 9ZAP - PART2 Bedienungsanleitung
HR Matic
HR Matic HR MULTI 3 Bedienungsanleitung
