Panasonic OneHome BB-HCM311A Bedienungsanleitung

HomeLogic LLC 100 Hoods Lane Marblehead, MA 09145 Phone (781) 639-5155 Fax (781) 639-9677

OneHome



Camera Integration Note

Manufacturer: Panasonic

Model Number(s): BB-HCM311A, BB-HCM331A, KX-HCM110A

OneHome Versions: 3.0 (all builds), 4.0 (all builds)

Comments: Network Camera (EasyConfig.exe version 1.0.21)

Document Revision Date: 9/6/2006

VERVIEW AND

UPPORTED

EATURES

Installing the Panasonic camera can be broken down into the following steps:

1. Install cameras at desired locations, and pull power and Cat5 cabling as needed. Refer to the

Panasonic documentation for mounting details.

2. Connect the cameras electrically to the home network and configure the cameras. See Camera

Configuration.

3. Integrate the cameras into the OneHome system and test proper operation. This step is outlined

in HomeLogic Configuration Details.

THESE CAMERAS SUPPORT THE FOLLOWING FEATURES:

Pan / Tilt: The camera can be turned to see various locations.

Built-in Audio: There is a built-in microphone as well as a jack for an external microphone. Audio from

the Panasonic cameras is supported in version 4.0 and later.

Presets: Some of these camera models also support presets, allowing the user to store predefined

locations such as a driveway or pool. This feature requires OneHome software version 4.0 or later.

AMERA

ONFIGURATION

The camera configuration is done with software provided by Panasonic, which must be run from a

computer with Windows also connected to the same network as the camera.

The software program from Panasonic is EasyConfig.exe: the version we checked is shown at the top.

IMPORTANT NOTES

1. Cameras must be configured one at a time: If you are installing more than one camera, setup

the first one completely before powering up subsequent cameras.

2. Setup the camera within 20 minutes: Initial settings must be made within 20 minutes of the

camera being turned on. If the camera has been powered up for more than 20 minutes, cycle

power to the camera before proceeding.

3. DON’T LOSE THE CAMERA PASSWORD: During setup you will create a user name and

password, which are required to make any other changes in the future. If you lose the user name

or password you will have to factory reset the camera and repeat this entire procedure.

4. DEFAULT USER NAME / PASSWORD: For Panasonic cameras, our default user name is

Administrator and our default password is password.

2 of 9

STARTING THE PANASONIC CAMERA SOFTWARE

1. Insert the CD from the camera into your PC: once it starts up, click Camera Setup. Or, if you

have copied the files from the CD to your computer, locate and start EasyConfig.exe.

2. Wait a moment to allow the software to find the camera: the following screen appears.

3. Select the desired camera, then click Execute to bring up the camera dialog shown below:

4. Click Automatic Setup: after a short delay you will see a new browser window with the password

settings as shown below:

5. Type in your desired user name and password: these values are not needed by the OneHome

system, but must be recorded and saved to make settings to the camera. By default we set the

user name to Administrator and the password to password.

3 of 9

6. You will be prompted to enter your user name and password again, as shown in the image below.

Type in the user name and password you just set, and click OK.

7. After a short delay, you should see a new browser window, similar to that shown under Camera

Settings below.

8. If the Automatic Setup dialog is still present, click its Cancel button. If the Easy Setup window is

still open on your desktop, close that window now as well.

4 of 9

CAMERA SETTINGS

1. After typing in your user name and password, you will be shown the standard browser interface to

the camera.

2. The system will attempt to install an ActiveX control to show the camera image in the browser

window. This control is not needed for proper OneHome operation, but is needed if you wish to

see the camera image on that computer. If any dialogs appear, close them or accept the ActiveX

control as appropriate for your situation.

3. On Windows computers with popup blocking enabled, you will need to click the bar to enable the

installation of the ActiveX control (as shown below).

4. Click Setup at the top to bring up the screen shown below:

5 of 9

5. Click UPnP on the left, then click Disable in the both parts of the screen, as shown below. Click

Save to store your settings.

6. Under Accounts to the left, click Administrator to bring up the screen below. Click Permit

access from guest users, as shown below. Re-enter your password in the boxes, then click

Save to store your changes.

6 of 9

7. Under Accounts to the left, click General User to bring up the screen shown below.

8. Click Guest in the list, then click Modify. This brings up the Access Level options. Select

Unlimited in the drop down, as shown below, and then check (turn on) all the options, as shown

below. Click Save to save your settings.

7 of 9

9. Click Network(IPv4) to bring up the network settings screen shown below.

10. Click Static in the Connection Mode to bring up the screen below.

11. Set the IP address to the desired value: we suggest setting the first camera to 192.168.0.80, the

second to 192.168.0.81, and so forth. Check that the other settings match the screen below, then

click Save to save the settings.

8 of 9

12. If prompted, click to Restart to restart the camera. Note that the camera is now at a different IP

address, so the browser window won’t show the camera.

13. Go to the address line in the browser, and put in the new IP address as shown below:

14. This brings up the camera’s home page shown below:

15. The camera is now at the correct IP address with the correct settings.

16. Close the browser.

9 of 9

OME

OGIC

ONFIGURATION

ETAILS

The following table provides settings used in the HomeLogic Configurator. Please refer to the Configurator Reference Guide for more details.

In the table below:

o“<User Defined>”, etc. Type in the desired name for the item.

OME

OFTWARE

ERSION

3.0

Devices Variable Name Setting Comments

Communication Device N/A (See Note 1) N/A (See Note 1)

Video Cameras Name

<User Defined> (Default:

Panasonic KX/BL/BB Series

)

Device Type Panasonic KX/BL/BB Series

Location <User Defined> (Not Required)

IP Address

<User Defined> (Default:

192.168.0.80

) (See Note 2)

Notes:

1. No

Communication Device

is needed: just add

Video Cameras

2. By default, set the first camera to 192.168.0.80, the second to 192.168.0.81, and so on.

OME

OFTWARE

ERSION

4.0

Devices Variable Name Setting Comments

Communication Device N/A (See Note 1) N/A (See Note 1)

Video Cameras Name

<User Defined> (Default:

Panasonic BB-HCM311A,331A

)

Device Type Panasonic BB-HCM311A,331A

Location <User Defined> (Not Required)

IP Address

<User Defined> (Default:

192.168.0.80

) (See Note 2)

Notes:

1. No

Communication Device

is needed: just add

Video Cameras

2. By default, set the first camera to 192.168.0.80, the second to 192.168.0.81, and so on.

Andere Handbücher für OneHome BB-HCM311A

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Panasonic Sicherheitskamera Handbücher

Panasonic

Panasonic WV-CW374 Bedienungsanleitung

Panasonic

Panasonic WV-CF300L Series Bedienungsanleitung

Panasonic

Panasonic BL-C210 Series Bedienungsanleitung

Panasonic

Panasonic BL-C30A - Wireless 802.11 b/g Network Camera Bedienungsanleitung

Panasonic

Panasonic KX-HCM10 Bedienungsanleitung

Panasonic

Panasonic WVNF302 - NETWORK CAMERA Handbuch

Panasonic

Panasonic WV-NP304E Bedienungsanleitung

Panasonic

Panasonic WV-SPN311 Bedienungsanleitung

Panasonic

Panasonic WV-SC384 Bedienungsanleitung

Panasonic

Panasonic WV-SW175 Bedienungsanleitung

Panasonic

Panasonic BL-VT164 Series Bedienungsanleitung

Panasonic

Panasonic WVBP120 - CCTV CAMERA Bedienungsanleitung

Panasonic

Panasonic WV-SF330 Series Bedienungsanleitung

Panasonic

Panasonic AWE300 - COLOR CAMERA Bedienungsanleitung

Panasonic

Panasonic KX-HNC600 Bedienungsanleitung

Panasonic

Panasonic i-Pro WV-SP102 Bedienungsanleitung

Panasonic

Panasonic WVCS564 - COLOR CCTV CAMERA Bedienungsanleitung

Panasonic

Panasonic Micro SD AW-HN40HKPC Bedienungsanleitung

Panasonic

Panasonic WVNM100 - NETWORK COLOR CAMERA Bedienungsanleitung

Panasonic

Panasonic WV-SW396 Bedienungsanleitung

Panasonic

Panasonic WV-SUD638 Bedienungsanleitung

Panasonic

Panasonic OneHome BB-HCM311A Bedienungsanleitung

Panasonic

Panasonic WVCP210 - COLOR CAMERA Bedienungsanleitung

Panasonic

Panasonic WV-CL270 Bedienungsanleitung

Beliebte Sicherheitskamera Handbücher anderer Marken

Okina USA

Okina USA SIR36-870VF650LP Bedienungsanleitung

Divio

Divio NDR155PA Bedienungsanleitung

Canon

Canon VB-C500D Bedienungsanleitung

Easy Access

Easy Access EasyGuard Bedienungsanleitung

Vivotek

Vivotek FD9389-EHV-v2 Bedienungsanleitung

TUYA

TUYA COSMO W2 Bedienungsanleitung

Eusso

Eusso UNC7500-IR Einrichtungshandbuch

urmet domus

urmet domus 1096/204 Bedienungsanleitung

VC VC20 series Bedienungsanleitung

Axis

Axis Q1614 Bedienungsanleitung

ieGeek

ieGeek DD201 Bedienungsanleitung

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Bedienungsanleitung

Vicon

Vicon V662-D-1 Betriebsanleitung

Grundig

Grundig GCH-K0274P Bedienungsanleitung

Lorex

Lorex VANTAGE LBC7032 Bedienungsanleitung

4xem

4xem WPT Bedienungsanleitung

Samsung

Samsung SCV-3082 Bedienungsanleitung

Vitek

Vitek VTC-C544 Bedienungsanleitung