Panasonic TY-42TM5H Bedienungsanleitung

ORDERNO. ITD0207023C2

Tuner Terminal Board

TY-42TM5H / TY-37TM5H

Unauthorized copying and distribution isaviolation of law.

1. Prevention of Electro Static Discharge (ESD) to

Electrostatically Sensitive (ES) Devices

Some semiconductor(solidstate) devices canbe damagedeasilybystatic electricity. Such

components commonlyare calledElectrostaticallySensitive (ES) Devices. Examples of typical

ES devices are integratedcircuits and some field-effect transistors and semiconductor"chip"

components. The following techniques shouldbe usedtohelpreduce the incidence of

component damage causedbyelectrostatic discharge (ESD).

1. Immediatelybefore handling anysemiconductor component or

semiconductor-equipped assembly, drainoff anyESDon your

bodybytouching aknownearth ground. Alternatively, obtainand

wear acommerciallyavailabledischarging ESDwrist strap, which

shouldbe removed for potential shock reasons prior to applying

power to the unitunder test.

2. After removing an electrical assemblyequipped with ES devices,

place the assemblyon aconductive surface such as alminum foil,

to prevent electrostaticcharge buildup or exposure of the

assembly.

3. Use onlyagrounded-tipsoldering iron to solder or unsolder ES

devices.

4. Use onlyan anti-staticsolder removal device. Some solder

removal devices not classified as "anti-static(ESDprotected)"

can generate electrical charge sufficient to damage ES devices.

5. Donot use freon-propelled chemicals. These can generate

electrical charges sufficient to damage ES devices.

6. Donot remove areplacement ES device from its protective

package until immediatelybefore you are readyto install it. (Most

replacement ES devices are packaged with leads electrically

shorted together byconductive foam, alminum foil or comparable

conductive material).

7. Immediatelybefore removing the protective material from the

leads of areplacement ES device, touch the protective material to

the chassisor circuitassemblyinto which the device will be

installed.

Caution

Besure no power isapplied to the chassisor circuit, and observe

all other safetyprecautions.

8. Minimize bodilymotions when handling unpackaged replacement

ES devices. (Otherwise hamless motion such as the brushing

together of your clothes fabricor the lifting of your foot from a

carpeted floor can generate staticelectricity(ESD)sufficient to

damage an ES device).

2. About lead free solder (PbF)

Note: Leadis listedas (Pb) inthe periodic table of elements.

Inthe information below, Pbwill refertoLeadsolder, and PbF will refertoLeadFree Solder.

The LeadFree Solderusedinourmanufacturing process and discussedbelowis (Sn+Ag+Cu).

That is Tin(Sn), Silver(Ag) and (Cu) although othertypes are available.

This model uses PbFree solderinit’s manufacture due toenvironmental conservation issues.

Forservice and repairwork, we’dsuggest the use of Pbfree solderas well, although Pbsolder

maybe used.

PCBs manufacturedusing leadfree solderwill have the PbF withina leaf Symbol

stampedon the back of PCB.

Caution

-Pb free solder has ahigher melting point than standard solder.

Typicallythe melting point is50 ~ 70 ~F(30~40~C)higher. Please

use ahigh temperature soldering iron and set itto 700 ± 20 ~F

(370 ± 10 ~C).

-Pb free solder will tend to splash when heated too high (about 1100

~For600~C).

Ifyou must use Pb solder, please completelyremove all of the Pb

free solder on the pins or solder area before applying Pb solder. If

thisisnot practical, be sure to heat the Pb free solder until it

melts, before applying Pb solder.

-After applying PbF solder to doublelayered boards, please check

the component side for excess solder which mayflow onto the

opposite side. (see figure below)

SuggestedPbfree solder

There are several kinds of Pbfree solderavailable forpurchase. This product uses Sn+Ag+Cu

(tin, silver, copper) solder. However, Sn+Cu(tin, copper), Sn+Zn+Bi (tin, zinc, bismuth) solder

canalsobe used.

3. Conductor Views

3.1. H-Board (TY-37/42TM5H)

4. Block and Schematic Diagrams

4.1. SchematicDiagram Notes

4.2. H-Board (TY-37/42TM5H)Block and SchematicDiagrams

5. Replacement Parts List

5.1. Replacement Parts List Notes

5.2. Replacement Parts List

Ref. No. PartNo. PartName& Description Pcs Remarks

C3451-54 TCUY1C105ZFN C 1UF, 16V 4 F1J1C1050006

C3455,56 ECJ2VF1C105Z C 1UF, Z, 16V 2

C3457,58 ECJ3XB0J106M C 10UF, M,6.3V 2

C3459 EEVHB1C470 E47UF, 16V 1

C3460 ECJ2VF1E104Z C 0.1UF, Z, 25V 1

C3461,62 EEVHB1C470 E47UF, 16V 2

C3463,64 ECJ2VF1C104Z C 0.1UF, Z, 16V 2

C3465,66 EEVHB1C470 E47UF, 16V 2

C3467 ECJ2VF1C104Z C 0.1UF, Z, 16V 1

C3468 EEVHB1C470 E47UF, 16V 1

C3506 TCUY0J685MBM C 6.8UF, 6.3V 1 F1K0J685A003

D3451,52 MA153 DIODE 2 MA3X153

H1 K1KB50B00030 50PCONNECTOR 1

H2 K1KB40B00015 40PCONNECTOR 1

IC3451 C0ZBZ0000205 IC 1

IC3699 TVRJ594 IC 1

JK3311 K1FB126B0014 CONNECTOR 1

L3451-54 TLK212T256AL EMI FILTER 4 J0HAAB000012

L3455-57 TLK20LFA224M EMI FILTER 3 J0HABB000004

L3458-60 ELJPA100KB CHIPINDUCTOR 3

Q3451-54 2SD601A TRANSISTOR 4 2SD0601A

Q3455 2SB709A TRANSISTOR 1 2SB0709A

Q3456,57 2SD601A TRANSISTOR 2 2SD0601A

Q3458 2SB709A TRANSISTOR 1 2SB0709A

Q3459 2SD601A TRANSISTOR 1 2SD0601A

R3451-54 ERJ3GEYJ560 M 56 OHM,J,1/16W 4

R3455,56 ERJ6GEYJ184 M 180KOHM,J,1/10W 2

R3457,58 ERJ6GEYJ472 M 4.7KOHM,J,1/10W 2

R3459-61 ERJ6ENF75R0 M75 OHM, 1/10W 3

R3462 ERJ6GEYJ560 M 56 OHM,J,1/10W 1

R3463,64 TAJAAH0101JV M 100 OHM,J,1/16W 2 D0GB101JA006

R3465-68 ERJ3GEYJ333 M 33KOHM,J,1/16W 4

R3469-71 TAJAAH0101JV M 100 OHM,J,1/16W 3 D0GB101JA006

R3472 ERJ3GEYJ153 M 15KOHM,J,1/16W 1

R3473 ERJ3GEYJ333 M 33KOHM,J,1/16W 1

R3474 TAJAAH0101JV M 100 OHM,J,1/16W 1 D0GB101JA006

R3475 ERJ3GEYJ102 M 1KOHM,J,1/16W 1

R3476,77 TAJAAH0101JV M 100 OHM,J,1/16W 2 D0GB101JA006

R3478 ERJ3GEYJ102 M 1KOHM,J,1/16W 1

R3479,80 ERJ3GEYJ472 M 4.7KOHM,J,1/16W 2

R3481 TAJAAH0101JV M 100 OHM,J,1/16W 1 D0GB101JA006

R3482 ERJ3GEYJ102 M 1KOHM,J,1/16W 1

R3483,84 ERJ3GEYJ3R3 M3.3OHM,J,1/16W 2

R3485 ERJ3GEYJ153 M 15KOHM,J,1/16W 1

R3486 ERJ3GEYJ333 M 33KOHM,J,1/16W 1

R3487,88 TAJAAH0101JV M 100 OHM,J,1/16W 2 D0GB101JA006

Ref. No. PartNo. PartName& Description Pcs Remarks

R3489 ERJ3GEYJ102 M 1KOHM,J,1/16W 1

R3490 TAJAAH0101JV M 100 OHM,J,1/16W 1 D0GB101JA006

R3491,92 ERJ3GEYJ472 M 4.7KOHM,J,1/16W 2

R3493 ERJ3GEYJ153 M 15KOHM,J,1/16W 1

R3494 ERJ3GEYJ333 M 33KOHM,J,1/16W 1

R3495 TAJAAH0101JV M 100 OHM,J,1/16W 1 D0GB101JA006

R3496,97 ERJ3GEYJ3R3 M3.3OHM,J,1/16W 2

R3498 ERJ3GEYJ102 M 1KOHM,J,1/16W 1

R3499 TAJAAH0101JV M 100 OHM,J,1/16W 1 D0GB101JA006

R3521,22 ERJ3GEYJ103 M 10KOHM,J,1/16W 2

RTL TXN/H10JKS-K CIRCUITBOARD H 1 TY-42TM5H

RTL TXN/H10KJS-K CIRCUITBOARD H 1 TY-37TM5H

MISCELLANEOUS

THEA068N SCREW 2

THEL023Z SCREW 4

TPCB13117 CARTON BOX 1 TY-42TM5H

TPCB13118 CARTON BOX 1 TY-37TM5H

TPDF0726 PARTITION 1

TPEH161 AIR MAT 1

TQBC0511 INSTRUCTION BOOK 1

TQBC7062 INSTRUCTION SEET 1

TQE6691 POLYBAG 1

XTV3+10J SCREW 1

XYN3+F8 SCREW 4

XZBT6506 POLYBAG 1

6. Schematic Diagram for printing with A4 size

TY-37TM5H/TY-42TM5H

H-Board Block and Schematic Diagrams TY-37TM5H/TY-42TM5H

H-Board Block and Schematic Diagrams

Components identified by mark have special characteristics important for safety.

When replacing any of these components, use only manufacture's specified parts.

Important Safety Notice

Notes:

1. Resistor

All resistors are cabon 1/4W resistor, unless marked as follows:

Unit of resistance is OHM [

] (K=1,000, M=1,000,000).

: Nonflammable : Metal Oxide

: Solid : Metal Film

: Wire Wound : Fuse:

2. Capacitor

All capacitors are ceramic 50V capacitor, unless marked as follows:

Unit of capacitance is

F, unless otherwise noted.

: Temperature Compensation : Electrolytic

: Polyester : Bipolar

: Metalized Polyester : Dipped Tantalum

: Polypropylene : Z-Type

3. Coil

Unit of inductance is

F, unless otherwise noted.

4. Test Point : Test Point position

5. Earth Symbol

: Chassis Earth (Cold) : Line Earth (Hot)

6. Voltage Measurement

Voltage is measured by a DC voltmeter.

Conditions of the measurement are the following:

Power Source ................................................... AC 120V, 50/60Hz

(North America model)/AC220-240V,

50/60Hz (Except North America)

Receiving Signal ............................................... Colour Bar signal (RF)

All customer's controls ...................................... Maximum positions

7. Number in red circle indicates waveform nember.

(See waveform pattern table.)

8. When arrow mark ( ) is found, connection is easily found from the direction of arrow

9. Indicates the major signal flow. : Video Audio

10. This schematic diagram is the latest at the time of printing and subject to change without

notice.

m T

TY-37TM5H/TY-42TM5H

Schematic Diagram Notes

Remarks:

1. The Power Circuit contains a circuit area which uses a separate power supply to isolate the

earth connection.

The circuit is defined by HOT and COLD indications in the schematic diagram. Take the

follwing precautions.

All circuits, except the Power Circuit, are cold.

Precautions

a. Do not touch the hot part or the hot and cold parts at the same time or you may

be shocked.

b. Do not short- circuit the hot and cold circuits or a fuse may blow and parts may

break.

c. Do not connect an instrument, such as an oscilloscope, to the hot and cold

circuits simultaneously or a fuse may blow.

Connect the earth of instruments to the earth connection of the circuit being

measured.

d. Make sure to disconnect the power plug before removing the chassis.

2. Following diodes are interchangeable.

MA150- MA162 (Replacement part)

TY-37TM5H/TY-42TM5H

Schematic Diagram Notes

4 Block and Schematic Diagrams

4.1. Schematic Diagram Notes

Components identified by mark have special characteristics important for safety.

When replacing any of these components, use only manufacture's specified parts.

Important Safety Notice

Notes:

1. Resistor

All resistors are cabon 1/4W resistor, unless marked as follows:

Unit of resistance is OHM [

] (K=1,000, M=1,000,000).

: Nonflammable : Metal Oxide

: Solid : Metal Film

: Wire Wound : Fuse:

2. Capacitor

All capacitors are ceramic 50V capacitor, unless marked as follows:

Unit of capacitance is

F, unless otherwise noted.

: Temperature Compensation : Electrolytic

: Polyester : Bipolar

: Metalized Polyester : Dipped Tantalum

: Polypropylene : Z-Type

3. Coil

Unit of inductance is

F, unless otherwise noted.

4. Test Point : Test Point position

5. Earth Symbol

: Chassis Earth (Cold) : Line Earth (Hot)

6. Voltage Measurement

Voltage is measured by a DC voltmeter.

Conditions of the measurement are the following:

Power Source ................................................... AC 120V, 50/60Hz

(North America model)/AC220-240V,

50/60Hz (Except North America)

Receiving Signal ............................................... Colour Bar signal (RF)

All customer's controls ...................................... Maximum positions

7. Number in red circle indicates waveform nember.

(See waveform pattern table.)

8. When arrow mark ( ) is found, connection is easily found from the direction of arrow

9. Indicates the major signal flow. : Video Audio

10. This schematic diagram is the latest at the time of printing and subject to change without

notice.

m T

TY-37TM5H/TY-42TM5H

Schematic Diagram Notes

Remarks:

1. The Power Circuit contains a circuit area which uses a separate power supply to isolate the

earth connection.

The circuit is defined by HOT and COLD indications in the schematic diagram. Take the

follwing precautions.

All circuits, except the Power Circuit, are cold.

Precautions

a. Do not touch the hot part or the hot and cold parts at the same time or you may

be shocked.

b. Do not short- circuit the hot and cold circuits or a fuse may blow and parts may

break.

c. Do not connect an instrument, such as an oscilloscope, to the hot and cold

circuits simultaneously or a fuse may blow.

Connect the earth of instruments to the earth connection of the circuit being

measured.

d. Make sure to disconnect the power plug before removing the chassis.

2. Following diodes are interchangeable.

MA150- MA162 (Replacement part)

TY-37TM5H/TY-42TM5H

Schematic Diagram Notes

4 Block and Schematic Diagrams

4.1. Schematic Diagram Notes

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Panasonic Tuner Handbücher

Panasonic

Panasonic WJ-ND300A Bedienungsanleitung

Panasonic

Panasonic WJ-ND300A Handbuch

Panasonic

Panasonic WJ-NX400K Bedienungsanleitung

Panasonic

Panasonic WJ-ND300 Administrator Console Bedienungsanleitung

Panasonic

Panasonic WJND200 - NETWORK DISK RECORDER Bedienungsanleitung

Panasonic

Panasonic Ramsa WX-RP800 Bedienungsanleitung

Panasonic

Panasonic CY-DAB2000N Bedienungsanleitung

Panasonic

Panasonic CQ-F61EG Bedienungsanleitung

Panasonic

Panasonic WJ-ND300 Administrator Console Bedienungsanleitung

Panasonic

Panasonic TY-FB8TA Bedienungsanleitung

Panasonic

Panasonic WJ-NX400K Betriebsanleitung

Panasonic

Panasonic WJ-NX300K Bedienungsanleitung

Panasonic

Panasonic TY-FB8TA Bedienungsanleitung

Panasonic

Panasonic WJ-NX400K/GJ Bedienungsanleitung

Panasonic

Panasonic TU-PTA500U Bedienungsanleitung

Panasonic

Panasonic WJ-NX400K Bedienungsanleitung

Panasonic

Panasonic SA-EH60X Bedienungsanleitung

Panasonic

Panasonic TY-42TM6MA Bedienungsanleitung

Panasonic

Panasonic BB-HNP15A Bedienungsanleitung

Panasonic

Panasonic WJ-NX400G-54000T6 Bedienungsanleitung

Panasonic

Panasonic RAMSA WX-RP800 Bedienungsanleitung

Panasonic

Panasonic WJ-NX200G Bedienungsanleitung

Panasonic

Panasonic WJ-VPU4000 Bedienungsanleitung

Panasonic

Panasonic TY-FB9TU Bedienungsanleitung

Beliebte Tuner Handbücher anderer Marken

Tunersys

Tunersys WS16 1 Bedienungsanleitung

Arcam

Arcam DT91 Bedienungsanleitung

Magnum

Magnum MD 102T Bedienungsanleitung

HDHomeRun

HDHomeRun 20121008 Bedienungsanleitung

Crestron

Crestron C2N-TXM Bedienungsanleitung

Eico

Eico HFT-92 Bedienungsanleitung

MFJ

MFJ MFJ-928 Bedienungsanleitung

NAD

NAD C 445 Bedienungsanleitung

Sony

Sony ST-SA5ES Bedienungsanleitung

Sirius Satellite Radio

Sirius Satellite Radio SC-FM1 Bedienungsanleitung

Antique Automobile Radio

Antique Automobile Radio 283501B Bedienungsanleitung

Monacor

Monacor PA-1200R Bedienungsanleitung

Technics

Technics ST-X301L Bedienungsanleitung

Manhattan

Manhattan 176156 Bedienungsanleitung

Marantz

Marantz ST-15S1 Bedienungsanleitung

Korg

Korg HA-40 Bedienungsanleitung

Harman Kardon

Harman Kardon TU915 Bedienungsanleitung

Teac

Teac T-1D Bedienungsanleitung