Panduit PZICEA Bedienungsanleitung

INSTALLATION INSTRUCTIONS CM361C

FOR TECHNICAL SUPPORT www.panduit.com/resources/install_maintain.asp

Page 1 of 8

PANZONE In-Ceiling Enclosure

PZICEA Active Equipment Version

Part Numbers:PZICEA

List of Components:

(1) Set of two Keys

(1) Left Mounting Bracket

(1) Right Mounting Bracket

(1) Fan Module

(6) Grommets

(2) Tak-Ty Rolls (Hook and Loop)

(4) Self-Tapping #10-32 screws

(1) Ceiling Tile Template

(1) Electrical Junction Box

(1) Integrated Horizontal Slack Manager

(1) Adjustable Air Dam

(2) Filters

(4) Entry/Exit Knockout Plates

Install in Ceiling..........................................................................................................................................

Electrical Installation.................................................................................................................................

Equipment Installation...............................................................................................................................

Cable Routing and Slack...........................................................................................................................

Patch Cord Management...........................................................................................................................

Maintenance...............................................................................................................................................

Accessories................................................................................................................................................

Table of Contents

Fan Module

Air Inlet

Entry/Exit Knockout Plates (4x)

Electrical Junction Box

Mounting Brackets

Keyed Locks

Integrated

Horizontal

Slack Manager

Adjustable Air

Dam

#10-32 screwsSet of two keys Grommets Ceiling tile template Tak -Ty Rolls

Note: Enclosure door load rating

is 50 lbs.

INSTALLATION INSTRUCTIONS CM361C

For Technical Support: www.panduit.com/resources/install_maintain.asp

Page 2 of 8

Install in Ceiling

Install (4) threaded rods to the building structure. The threaded rod must

be attached on all four corners of the enclosure with a nut and washer

above and below the support bracket. Level the enclosure so the weight

is not supported by the ceiling grid system.

Ceiling Tile Cutout

Place the included ceiling tile cutout template over

the removed ceiling tile. Secure the template with

tape of thumb tacks. Trace the outline with a utility

knife to extract the necessary shape to insert into

the enclosure.

While the enclosure is installed in the ceiling and open, remove the (3) #6-32 screws and ceiling tile bracket as shown below. Once

removed, slide the ceiling tile cutout into place fitting around the fan module. After proper orientation is achieved, replace the ceiling tile

bracket and the (3) #6-32 screws back into enclosure.

Insert Ceiling Tile Cutout into Housing

#6-32

Screws

Ceiling Tile

Bracket

Ceiling Tile

Cutout

Ceiling Tile

Tem pl a t e

Thumb Tacks

INSTALLATION INSTRUCTIONS CM361C

For Technical Support: www.panduit.com/resources/install_maintain.asp

Page 3 of 8

Electrical Installation

Included with the product is a standard electrical junction box. Mounting and installing the electrical components and receptacles should be

completed by a experienced professional to the latest local building codes and regulations.

Conduit Knockouts

Mounting Holes

(Receptacles not included)

Mount the electrical box to the side of the enclosure.

Use (4) # 10-32 thread cutting screws to attach the

box to the exterior.

Cross-sectional view from inside enclosure

NOTE: Install power per local building codes and regulations.

#10-32 Thread Cutting Screws

Mounting the Electrical Junction Box

Above the junction box is shown with already

installed receptacles.

INSTALLATION INSTRUCTIONS CM361C

For Technical Support: www.panduit.com/resources/install_maintain.asp

Page 4 of 8

Active/Passive Network Equipment Installation

Adjust the brackets forward or backward to accommodate the desired depth for the intended active equipment. Shown below are two

examples of where to attach the mounting brackets, however the brackets can be adjusted in 1/2” increments to better fit desired network

active equipment.

Mounting position for fiber termination box

3 RU for Patch Panels

facing forward

2 RU for Network Switches

Brackets mounted toward front

for deepest active equipment

Recommended for switches

17.5” deep

Brackets mounted toward back

for shallower active equipment

Recommended for switches

15.5” or less

Mount the desired equipment to the recommended mounting locations. The upper level of the brackets are recommended for use with

patch panel applications while the lower level is designed to hold your network switches.

Note: Maintain a minimum gap of approximately 1/2” (12mm) between the door and the bottom of the switch for air flow.

Integrated Horizontal Slack Manager

3 RU for Patch Panels

facing back

INSTALLATION INSTRUCTIONS CM361C

For Technical Support: www.panduit.com/resources/install_maintain.asp

Cable Routing and Slack Management

Determine the direction of the incoming and

outgoing cables in order to select which

entry/exit knockouts to remove. Once

removed install the grommets from the inside

of the enclosure. (Each grommet is designed

to hold 48 Category 6a cables.)

NOTE: Allow a minimum of 14” of cable slack to allow the door to open and close properly.

Entry/Exit knockouts

Page 5 of 8

Cable Routing

Enclosure door openEnclosure door closed

Utilizing the four back grommets requires a proper slack loop to allow the door to open and close properly. The diagrams below illustrate

how to route the cables and where to secure the cables using a tie-down bar. The tie off point should be approximately 24” away from

cable entering point of enclosure and 6” above the top.

Tie down bar used

to secure cables

Secure cable at

this location

Secure cable at

this location

Tie down bar used

to secure cables

Note: Install all cabling in accordance with NEC article 300.22 and

article 800.

INSTALLATION INSTRUCTIONS CM361C

For Technical Support: www.panduit.com/resources/install_maintain.asp

Page 6 of 8

First bay of ports (12) on the switch

Shown to the right is the recommended patch cord

routing from (2) 48- port switches to (2) 48-port

patch panels.

The image below demonstrates how cables are

routed from switch to patch panels.

Step 1

Plug in a 3’ (1m) patch cord into a port on

the switch. Route patch cord up and into the

integrated horizontal slack manager. Create

a loop in the patch cord and bring forward.

Plug other end of the patch cord into the

desired jack in the patch panel.

Repeat the process for each bay of ports on

the switch. Use Tak Ties to secure cables to

sheer forms located on the horizontal slack

manager.

Cable Routing and Slack Management

INSTALLATION INSTRUCTIONS CM361C

For Technical Support: www.panduit.com/resources/install_maintain.asp

Patch Cord Management

Page 7 of 8

Step 2

Plug in a 3’ (1m) patch cord into a port on

the switch. Route patch cord up and into the

integrated horizontal slack manager. Create

a loop in the patch cord (opposite direction

of step 1) and bring forward. Plug other end

of the patch cord into the desired jack in the

patch panel.

Repeat the process for each bay of ports on

the switch. Use Tak Ties to secure cables to

sheer forms located on the horizontal slack

manager.

Step 3

Plug in a 3’ (1m) patch cord into a port on

the switch. Route patch cord up and into the

integrated horizontal slack manager. Create

a loop in the patch cord and bring forward.

Plug other end of the patch cord into the

desired jack in the patch panel.

Repeat the process for each bay of ports on

the switch. Use Tak Ties to secure cables to

sheer forms located on the horizontal slack

manager.

Second bay of ports (12) on the switch

Third bay of ports (12) on the switch

Fourth bay of ports (12) on the switch

Step 4

Plug in a 3’ (1m) patch cord into a port on

the switch. Route patch cord up and into the

integrated horizontal slack manager. Create

a loop in the patch cord (opposite direction

of step 3) and bring forward. Plug other end

of the patch cord into the desired jack in the

patch panel.

Repeat the process for each bay of ports on

the switch. Use Tak Ties to secure cables to

sheer forms located on the horizontal slack

manager.

INSTALLATION INSTRUCTIONS CM361C

For instuctions in Local Languages

and Technical Support:

www.panduit.com/resources/install_maintain.asp

E-mail:

[email protected]

Fax:

(708)444-6448

www.panduit.com

PZICGK

HARDWARE

Maintenance

Accessories

Annually Replace Filter Annually Clean Circulation Fan

PZICFRK

PZICGK

1. Remove (3) #6-32 thread cutting screws as shown.

2. Remove old filter and replace with new one.

3. Install filter bracket with (3) #6-32 thread cutting screws.

4. Repeat process on opposite side.

1. Unplug fan from power source.

2. Remove ceiling tile (see page 2).

3. Remove (4) #6-32 thread cutting screws as shown

4. Remove the remaining (4) #6-32s thread cutting screws on

opposite side.

Filter replacement kit Grounding and Bonding Kit

Top side (step 3)

Bottom side (step 4)

Filter pad Bracket

Grounding cables

Page 8 of 8

5 pairs of replacement filter pads

Inhaltsverzeichnis

Andere Panduit Netzwerkzubehör Handbücher

Panduit

Panduit Z11C Series Bedienungsanleitung

Beliebte Netzwerkzubehör Handbücher anderer Marken

Valcom

Valcom VIP-804 Bedienungsanleitung

SKUTCH

SKUTCH BA-1000 Produkthandbuch

QUNDIS

QUNDIS RNN5 Bedienungsanleitung

Asus

Asus AAEON FWS-2365 Bedienungsanleitung

Sophos

Sophos XG 85w Bedienungsanleitung

AMCI

AMCI RBE2-8 Bedienungsanleitung

Patton electronics

Patton electronics 2888 Bedienungsanleitung

Cradlepoint

Cradlepoint COR IBR1100/IBR1150 Bedienungsanleitung

Paradyne

Paradyne Hotwire 8620 Bedienungsanleitung

Infra Cool

Infra Cool F-1.3 Bedienungsanleitung

Edgewater Networks

Edgewater Networks 4300T Bedienungsanleitung

Edimax

Edimax SB-2200g Bedienungsanleitung

Extreme Networks

Extreme Networks Mogul-100 Bedienungsanleitung

Aaeon

Aaeon FWS-8500 Bedienungsanleitung

F5 BIG-IP 10000 Series Montageanleitung

ZyXEL Communications

ZyXEL Communications NMA1115 Bedienungsanleitung

Auerswald

Auerswald COMtrexx Business Bedienungsanleitung

Actisense

Actisense QNB-1-B Bedienungsanleitung