Paradox ZX82 Bedienungsanleitung

ZX82-EI02 01/2019 PARADOX.COM

ZX82

8-Zone Input

Expansion Module

Installation Manual

V1.10 and higher

Introduction

The ZX82, 8-zone Expansion Module, provides 8 zones input expansion to

Paradox panels; connects on the keypad bus of EVO, Spectra, or MG

panels. The ZX82 comes with its own tamper-proof enclosure and provides

Zone Status LED indicators as well as Power and Data.

Compatibility

• All Paradox control panels v6.80 or higher

• BabyWare v5.1 and higher

• Infield v5.1 and higher

Connections

Connect the four bus terminals labeled

+ -

GRN

YEL

of the module to the

corresponding terminals on the control panel as shown.

To enable anti-tamper switch input on EVO, use input terminal Z8 and enable

section

[001]

option

[1]

To enable anti-tamper switch input on MG/SP, use input terminal Z1 and enable

section

[706] option [4] for panel +1, option [5] for panel +9 and option [6] for

panel +17.

Upgrading Firmware

The ZX82’s firmware can be upgraded in Infield via BabyWare using a

307USB Direct Connect Interface.

LED Indicators

*If control panel has an AC Loss all LEDs are turned off.

Technical Specifications

* Control Panel shall be certified to EN 50131-6 and used as the power supply

for the expansion module. If an external power supply is used, it must be

certified for EN 50131-6.

The security grade of the ZX82 is dependent on the security grade of the

system where it is installed. The maximum security grade is 3.

External Anti-Tamper

Switch (N.C.)

LED OFF ON

POWER OFF OK (10.5V to 16V)

RX / TX No clock or data

exchange

Clock and data OK

ZONE1 to ZONE8* Zone Closed Zone Opened /

Ta m p e r

ATZ Enabled on EVO

ZONE1 to ZONE8

Both zones connected

to this input are Closed

Any Zone connected

to this input is

Opened / Tamper

Input Voltage 10.5 to 16 Vdc

Current Consumption 100mA MAX all LEDs On

Number of Inputs 8 standard zone inputs

Operating Temperature -20 C to +50 C (-4 F to 122 F)

Humidity 95% maximum

Dimensions (H x W x D) 16.5 cm x 10.2 cm x 2.5 cm

(6.5 in x 4 in x 1 in)

Certification*

CE, EN 50131-3 Security Grade: 3

Environmental Class: II

Certification Body: Applica Test and

Certification AS

Display

Power

Lock

Data

All manuals and user guides at all-guides.com

all-guides.com

ZX82-EI02 01/2019 PARADOX.COM

Programming EVO

1. Enter section [4003].

2. Enter the eight-digit module serial number.

3. Enter the three-digit module section number.

Module Tamper on Input-8

Section 001 - Bit 1, 0 = Disabled, 1 = Enabled

Note: If this option is enable the on-board tamper is disabled.

EOL/ATZ per Zone Input

Section 401 - Zone Input Options

Zone Input Options Individual Settings

EOL Resistor Value Selection

Section 402 - Zone Input Options

Zone Input Options Individual Settings

Programming MG/SP

1. Enter section [001] - [032].

2. Enter the two-digit zone definition.

3. Assign a partition.

4. Select or deselect zone options.

5. Press Enter.

6. Repeat steps 1 - 5 for remaining zones.

For more information on how to program zones, please refer to the MG/SP

Programming Guide.

Module Tamper on Input-1

Section 706 - Panel Programming

Note: If this option is enable the on-board tamper is disabled.

MG/SP Jumper Settings (Panel ATZ Off)

MG/SP Jumper Settings (Panel ATZ On)

Zone1 / Zone2 Zone3 / Zone4 Zone5 / Zone6 Zone7 / Zone8

_ / _

(0/0)

_ / _

(0/0)

_ / _

(0/0)

_ / _

(0/0)

OPTION DESCRIPTION

0System default; zone will follow global panel settings for EOL

1 EOL / ATZ disabled

2 EOL enabled / ATZ disabled

3 EOL disabled / ATZ enabled

4 EOL / ATZ enabled

Zone1 / Zone2 Zone 3 / Zone4 Zone5 / Zone6 Zone7 / Zone8

_ / _

(0/0)

_ / _

(0/0)

_ / _

(0/0)

_ / _

(0/0)

OPTION EOL Value Zone Value

01K 1K

12K2 1K5

23K3 3K3

34K7 4K7

44K7 6K8

52K2 4K7

68K2 8K2

72K2 2K2

Option Description Off ON

4ZX82 ID A (panel +1) Input 1 Zone input Tamper input

5ZX82 ID B (panel + 9) Input 1 Zone input Tamper input

6ZX82 ID C (panel + 17) Input 1 Zone input Tamper input

Module #

(Jumper) MG5000 MG5050 SP4000 SP5500 SP6000 SP65 SP7000

+1 3-10 6-13 5-12 6-13 9-16 10-17 17-24

+2 11-18 14-21 13-20 14-21 17-24 18-25 25-32

+3 19-26 22-29 21-28 22-29 25-32 26-32 N/A

Module #

(Jumper) MG5000 MG5050 SP4000 SP5500 SP6000 SP65 SP7000

+1 5-12 11-18 9-16 11-18 17-24 19-26 N/A

+9 13-20 19-26 17-24 19-26 25-32 27-32 N/A

+17 21-28 27-32 25-32 27-32 N/A N/A N/A

Warranty

For complete warranty information on this product, please refer to the Limited Warranty Statement

found on paradox.com/terms or contact your local distributor. Specifications may change without prior

notice.

Patents

US, Canadian and international patents may apply. Paradox is a trademark or registered trademark of

Paradox Security Systems (Bahamas) Ltd.

All manuals and user guides at all-guides.com

Andere Paradox Steuereinheit Handbücher

Paradox

Paradox RTX3 Bedienungsanleitung

Paradox

Paradox Digiplex EVO PRT3 Installationshandbuch

Paradox

Paradox ZX16D Bedienungsanleitung

Paradox

Paradox IP150+ Betriebsanleitung

Paradox

Paradox ZX82 Bedienungsanleitung

Paradox

Paradox PCS265 LTE Installationsanleitung

Paradox

Paradox IP150 Bedienungsanleitung

Paradox

Paradox IP180 Bedienungsanleitung

Paradox

Paradox DGP-LSN4 V1.1 Betriebsanleitung

Paradox

Paradox IP150 Bedienungsanleitung

Paradox

Paradox PCS265 Bedienungsanleitung

Paradox

Paradox IP150 Bedienungsanleitung

Paradox

Paradox ZX8 Bedienungsanleitung

Paradox

Paradox ZX82 Bedienungsanleitung

Paradox

Paradox MAGELLAN RTX3 V1.5 Bedienungsanleitung

Paradox

Paradox IP150+ Bedienungsanleitung

Paradox

Paradox Spectra 1759EX V1.0 Bedienungsanleitung

Paradox

Paradox Digiplex EVO EVO192 V7.11 Betriebsanleitung

Paradox

Paradox PCS265LTE Installationsanleitung

Paradox

Paradox PCS250G Installationsanleitung

Paradox

Paradox ZX8 Bedienungsanleitung

Paradox

Paradox MG-RCV3 Bedienungsanleitung

Paradox

Paradox PCS265 Installationsanleitung

Paradox

Paradox RPT1+ Bedienungsanleitung

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

GEA

GEA VARIVENT Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

Eaton

Eaton Powerware Series Bedienungsanleitung

WAGO

WAGO 750-407/040-000 Bedienungsanleitung

Sony

Sony CCU-590 Bedienungsanleitung

Graco

Graco 25D614 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung