Paradyne FrameSaver FLEX 9623 Bedienungsanleitung

FrameSaverFLEX 9623

Installation Instructions

Document Number 9623-A2-GN10-10

May 2000

Product Documentation on the World Wide Web

We provide complete product documentation online. This lets you search the

documentation for specific topics and print only what you need, reducing the waste

of surplus printing. It also helps us maintain competitive prices for our products.

Complete documentation for this product is available at www.paradyne.com.

Select

Library

→

Technical Manuals

→

FrameSaver Frame Relay Devices.

Select the following document:

9623-A2-GB20

FrameSaver FLEX

9623

User’s Guide

To order a paper copy of a Paradyne document:

Within the U.S.A., call 1-800-PARADYNE (1-800-727-2396)

Outside the U.S.A., call 1-727-530-8623

Upgrading a Basic FLEX Unit to FLEX SLV

An upgrade will soon be available for basic FrameSaverFLEX models (without SLV

features) that will allow activation of full FLEX SLV capability in the unit at any time. You

will simply order a FrameSaver FLEX 9123 SLV Activation Certificate. The certificate

can be ordered for a single unit or for many units. You must have the OpenLaneSLM

system to activate the additional FLEX SLV features in the unit.

To obtain an activation certificate, you will provide the model to be upgraded

(i.e., 9623), your OpenLane system license key number, and the number of

FrameSaver units to be upgraded to FLEX SLV capability. When you receive your

certificate, it will include a FLEX Activation Certificate number, the Feature Group

Number for the additional SLV features (Feature Group 2), your OpenLane license key

number, and the number of device activations (license keys) ordered.

When ready to activate FLEX SLV capability in the units, you will run the OpenLane

SLM application. It will prompt you for the serial numbers of the units to be activated,

their IP addresses, and whether the activations will be immediate or scheduled.

OpenLane then activates SLV capability in the designated units and the units are reset.

A report summary will be available that will provide information about the activation

certificate, the activated units, and the number of license keys remaining.

Contact your sales representative for additional information.

Package Checklist

Verify that your package contains the following:

FrameSaver FLEX unit

Power cord with a wall-mount 120 Vac power transformer

Self-mounting tie wrap for power cord strain relief

RJ48S modular cable for U.S. network access



FrameSaver FLEX

9623 Quick Reference

(Document No. 9623-A2-GL10)

Be sure to register your warranty at www.paradyne.com/warranty.

Before You Begin

Make sure you have:

A dedicated, grounded power outlet that is protected by a circuit breaker within

6 feet of the FrameSaver unit

A clean, well-lit, and ventilated site that is free from environmental extremes

One-to-two feet of clearance for cable connections

A physical connection to the frame relay DDS network

An asynchronous terminal or PC (personal computer)

If desired, an operable Ethernet LAN (Local Area Network) connection for access

by an NMS (Network Management System)

Configuration information for the FrameSaver unit being installed or replaced

Appropriate cables:

— Ethernet cable

— Data port cable

— COM port-to-terminal or COM port-to-PC cable

See the User’s Guide for additional information on:



Troubleshooting



Connectors, Cables, and Pin Assignments



Technical Specifications

Cables You May Need to Order

If connecting to . . . Order a . . . Feature

Number Part

Number

Equipment with

V.35 interfaces,

MS34 connectors

V.35 DTE adapter,

EIA-530A-to-V.35 3100-F1-570 035-0244-0031

Asynchronous

terminal or PC with

an 8-pin modular

interface/connector

Standard EIA-232

straight-through cable,

8-pin modular-to-DB25

(14 feet – 4.3 meters)

3100-F2-540 035-0314-1431

PC with a D-Sub9

interface/connector Standard EIA-232

straight-through cable,

D-Sub9-to-DB25

(14 feet – 4.3 meters)

3100-F2-550 035-0313-1431

External device

(e.g., a modem) Standard EIA-232-D

crossover cable

(14 feet – 4.3 meters)

9008-F1-550 035-0336-1431

Contact your sales representative to order cables.

Safety Instructions

Please refer to the

Important Safety Instructions

beginning on page 18.

Installing the Power Supply and Cord

1. Insert the power cord’s plug into the POWER jack.

00-16699

Grounded

Power

Outlet

ALM

TEST

OOS

OOF/NS

NetworkSystem Port

FrameSaverTM SLV

FrameSaver®FLEX

9623

ALM

System

COM NET

POWER

ETHERNET

2. Plug the power supply into the grounded power outlet and check the LEDs.

If any LEDs light, you have power. If not, refer to

Troubleshooting

in the User’s

Guide for possible explanations.

3. Insert the self-mounting tie wrap in the leftmost hole (hole with a dark circle around

it) until it snaps securely into place. The tie wrap provides strain relief for the power

cord.

4. Loop the tie wrap around the power cord, thread it through the hole at the base of

the wrap, and pull it snugly around the cord.

Connecting to an Asynchronous Terminal or PC

A VT100-compatible asynchronous terminal or a PC providing VT100 terminal

emulation must be used to set up access to and management of the unit.

1. Configure the terminal or PC so it is compatible with the FrameSaver unit:

– Baud Rate set to 19.2 kbps.

– Character length set to 8 data bits.

– Parity set to none.

– Stop bit set to 1.

– Flow Control set to None.

2. Insert the DB25 end of the EIA-232 cable into the FrameSaver unit’s COM port.

COM NET

POWER

ETHERNET

COM

Port

00-16685

3. Insert the other end of the cable into the terminal or PC.

4. Tighten the screws on each side of the connector to secure the cable.

5. Press Enter on the keyboard to display the Main Menu.

If the Main Menu does not appear, recheck the terminal or PC settings (see

Step 1), or press the Enter key. Refer to

Troubleshooting

in the User’s Guide for

other possible explanations.

Verifying that Self-Test Passed

To verify that the unit passed its self-test, go to the System and Test Status screen.

Main Menu

→

Status

→

System and Test Status

The results of the self-test appear directly under the screen title.

If any failure messages appear, reset the unit by disconnecting, then reconnecting the

power cord. The unit will perform the self-test again. If the failure reappears, call your

service representative for assistance.

A Quick Guide to Configuration

The FrameSaver unit should operate using the default (factory-set) configuration

options, with exception to the changes specified in these installation instructions. Refer

to the following table for help in navigating through the menus.

Press the . . . To . . .

Esc key Go back one screen or menu level. To see a visual

representation of the menu levels, see

Menu Hierarchy

the Quick Reference.

Tab key, or

Up (↑), Down (↓),

Left (←) and Right (→)

Arrow keys

Move the cursor from one menu item to the next.

Enter or Return key Complete the menu or option selection.

Spacebar Display the next available setting when changing a

configuration option. All the available settings for an

option appears at the bottom of the screen.

As an example, follow these steps to go to the Configuration Edit/Display menu so you

can start setting up the unit.

To load a configuration for editing:

1. From the Main Menu, press the down arrow key twice so the cursor is on

Configuration.

2. Press Enter to display the Configuration menu. The Load Configuration From

menu appears.

3. Press Enter to select Current Configuration (the cursor is already on this

selection). The Configuration Edit/Display menu appears.

This sequence of steps would be shown as the menu selection sequence:

Main Menu

→

Configuration

To save a configuration option change:

1. Press Ctrl-a to switch to the function keys area at the bottom of the screen.

2. Type sor S(Save) and press Enter. The Save Configuration To menu appears.

3. Press Enter again to save your changes to the Current Configuration.

4. Press Esc until the Configuration Edit/Display menu reappears to continue

configuring the unit.

Press Ctrl-a, type m(MainMenu), and press Enter to return to the Main Menu.

In the sections that follow, only the minimum option changes required are included so

you will have a quick and trouble-free installation. See the configuration option tables in

the User’s Guide for more information about configuration options.

About the Installation Procedures

There are two methods for installing and setting up the FrameSaver unit.

One person can install and set up the unit. If this is the case, see

Full Installation

and Setup

An installer can physically install and set up access to the unit, and the network

operation center (NOC) can complete the setup. If this is the case, see

Minimal

Installation for Service Providers

on page 9.

Certain procedures are common to both the full installation and minimal methods.

These procedures (starting with

Setting Up Local Management at the Central Site

page 10) are referenced in the full and minimal installation instructions. Refer to them,

as needed.

Full Installation and Setup

An Easy Install screen is provided to simplify installation and setup. The Easy Install

feature can be used when one person installs and sets up the FrameSaver unit from

beginning to end.

1. Select the Easy Install feature.

Main Menu

→

Easy Install

Easy Install Screen Example

main/easy_install 9623

Device Name: Node A 5/26/1999 23:32

EASY INSTALL

Service Type: Frame Relay

Node IP Address: 000.000.000.000 Clear

Node Subnet Mask: 000.000.000.000 Clear

TS Access: DLCI 980

Create a Dedicated Network Management Link

Ethernet Port Options Screen

DDS Line Rate (Kbps): Initialize From Network

Network Initiated DCLB: V.54 & ANSI

DSU Latching Loopback (64CC): Enable

Require DSU Latching Loopback Preamble Enable

–––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––

Ctrl-a to access these functions, ESC for previous menu MainMenu Exit

Save

2. Change the Service Type to Leased Line.

3. Enter the Node IP Address and Subnet Mask.

4. If the Ethernet port will be used, select the Ethernet Port Options Screen, and

configure the following:

– If the IP Address and Subnet Mask are unique to the interface, enter them for

the port; otherwise, the Node IP Address and Subnet Mask will be used.

– Enter the Default Gateway Address; the IP Address that will be used for packets

without a route.

– Enable Proxy ARP if the unit will proxy for downstream FrameSaver units

learned via the proprietary RIP (Routing Information Protocol) feature.

– Press the ESC key to return to the Easy Install screen.

5. Configure the DDS network interface options to match the service provider’s

settings.

6. If the unit will be enforcing CIR (Committed Information Rate) and EIR (Excess

Information Rate) on network frame relay links, enable Traffic Policing.

Main Menu

→

Configuration

→

System

→

Frame Relay and LMI

You can change other Frame Relay and LMI default settings, if necessary.

7. Configure each interface according to the local management interface (LMI) and

assigned line conditions supplied by the service provider.

Configuration

→

Network

→

Frame Relay

Configuration

→

Data Ports

→

Frame Relay

8. Set up SNMP management and local management (see

Setting Up Local

Management at the Central Site

on page 10).

9. Save the configurations.

10. Install the network cable (see

Connecting to the Network

on page 12). The

FrameSaver unit starts discovering DLCIs and network time slots (see

Automatic

Configuration

on page 11).

11. If SNMP traps are wanted, set up managers and select the desired traps (see

Configuring SNMP Trap Managers and Traps

on page 13).

12. Verify the entire path from the remote unit to the NMS is functioning (see

Verifying

the End-to-End Path

on page 13).

13. If the Ethernet port will be used for management, install the Ethernet cable (see

Connecting to the Ethernet

on page 14).

14. Install the DTE cable (see

Connecting to the DTE (Router or FRAD)

on page 15).

15. Verify that data is being received (see

Verifying That Data is Being Received

page 15).

16. Verify that all PVCs, including Management PVCs, are configured; and see

whether the PVC is active or not (see

Checking PVC Connections

on page 16).

The FrameSaver installation is complete.

Minimal Installation for Service Providers

In this set of procedures, once the unit is installed and minimal configuration is

completed using the Easy Install feature, the NOC can complete and verify the setup.

Physically Installing the Unit and Setting Up for Remote Access

1. Follow Steps 1 through 4 of

Full Installation and Setup

on page 7.

For non-managed networks

, set TS Access to DLCI, then select a DLCI on the

network interface to be used for the troubleshooting access link.

For managed networks

, create a Dedicated Network Management Link, selecting

a DLCI for the management link at the Which DLCI would you like to

Create a Dedicated Network Management Link on? prompt. The TS

Access Management Link that is created will be used by the NOC to access

the unit.

3. Save the configurations.

4. Install the network cable (see

Connecting to the Network

on page 12).

5. Install the Ethernet cable (see

Connecting to the Ethernet

on page 14).

6. Connect test equipment to the user data port, and have a BERT (Bit Error Rate

Test) performed between the far-end device and the FrameSaver unit.

7. Remove the test equipment and install the DTE cable (see

Connecting to the DTE

(Router or FRAD)

on page 15).

Physical installation of the unit is complete; the NOC can now remotely access the unit

for additional configuration.

Completing Setup of the Unit From the NOC

1. Access the remote FrameSaver unit.

–

For non-managed networks

, ping the FrameSaver unit five times within

five seconds. The unit automatically provisions the TS Access DLCI as a

non-multiplexed management DLCI.

–

For managed networks

, access the unit using the dedicated management link.

2. If the Ethernet port will be used, select the Ethernet Port Options Screen, and

configure the following:

– If the IP Address and Subnet Mask are unique to the interface, enter them for

the port; otherwise, the Node IP Address and Subnet Mask will be used.

– Enter the Default Gateway Address; the IP Address that will be used for packets

without a route.

– Enable Proxy ARP if the unit will proxy for downstream FrameSaver units

learned via the proprietary RIP (Routing Information Protocol) feature.

– Press the ESC key to return to the Easy Install screen.

3. Configure the DDS network interface options to match the service provider’s

settings.

4. Configure specific frame relay options, like CIR (committed information rate), and

any other configuration options requiring input or changes from the default settings.

5. Save the configurations.

6. Verify the entire path from the remote unit to the NOC NMS is functioning (see

Verifying the End-to-End Path

on page 13).

7. Verify that data is being received (see

Verifying That Data is Being Received

page 15).

8. Verify that all PVCs, including Management PVCs, are configured; and see

whether the PVC is active or not (see

Checking PVC Connections

on page 16).

The FrameSaver installation is complete.

Setting Up Local Management at the Central Site

1. Create a DLCI for the data port.

Configuration

→

Data Ports

→

DLCI Records

2. Save the configuration.

3. Create a Management PVC using the data port DLCI just created.

Configuration

→

Management and Communication

→

Management PVC

Minimally, enter the following options:

– Name for the management PVC

– Interface IP Address and Subnet Mask, if different from the Node’s

– Primary Link for this Management PVC (the user data port)

– Primary DLCI (i.e., the data port DLCI)

4. Save the configuration.

Inhaltsverzeichnis

Andere Paradyne Netzwerk-Router Handbücher

Paradyne

Paradyne Hotwire 6301 Bedienungsanleitung

Paradyne

Paradyne iMarc SLV 9126 Bedienungsanleitung

Paradyne

Paradyne 6212-A2 Bedienungsanleitung

Paradyne

Paradyne Hotwire 6341 Bedienungsanleitung

Paradyne

Paradyne BitStorm 6211 CPE Bedienungsanleitung

Paradyne

Paradyne Hotwire 6211 Montageanleitung

Paradyne

Paradyne JetFusion 2100 Series Bedienungsanleitung

Paradyne

Paradyne Hotwire 7995 Original Betriebsanleitung

Paradyne

Paradyne 1740 SHDSL Bedienungsanleitung

Paradyne

Paradyne FrameSaver DSL 9783 CSU/DSU Bedienungsanleitung

Paradyne

Paradyne FrameSaver DSL 9783 CSU/DSU Bedienungsanleitung

Paradyne

Paradyne Hotwire 6341 Bedienungsanleitung

Paradyne

Paradyne 1740 SHDSL Original Betriebsanleitung

Paradyne

Paradyne HotWire 5246 Bedienungsanleitung

Paradyne

Paradyne Hotwire 6211 Original Betriebsanleitung

Paradyne

Paradyne Hotwire 6321/6322 IDSL Router Bedienungsanleitung

Paradyne

Paradyne Hotwire 6351 Bedienungsanleitung

Paradyne

Paradyne FrameSaver 9783 Bedienungsanleitung

Paradyne

Paradyne Hotwire 6351 Bedienungsanleitung

Paradyne

Paradyne Hotwire 6301 Bedienungsanleitung

Paradyne

Paradyne FrameSaver 9720 Bedienungsanleitung

Paradyne

Paradyne FrameSaver SLV 9664 Bedienungsanleitung

Paradyne

Paradyne iMarc 9550 DS3 Bedienungsanleitung

Paradyne

Paradyne FrameSaver SLV 9664 Bedienungsanleitung

Beliebte Netzwerk-Router Handbücher anderer Marken

Allnet

Allnet ALL0333AU Bedienungsanleitung

HomeSeer

HomeSeer HT-SEL Bedienungsanleitung

Sercomm

Sercomm Genesis OC3505D Bedienungsanleitung

Billion

Billion BIPAC 5102 Series Bedienungsanleitung

TP-Link

TP-Link TD-8817 Bedienungsanleitung

Motorola

Motorola MR1900 Bedienungsanleitung

Digi

Digi IX14 Bedienungsanleitung

Cisco

Cisco NCS 540 Handbuch

XAVi

XAVi X8821e Bedienungsanleitung

BEC

BEC 6200WZL Bedienungsanleitung

MikroTik

MikroTik hAP ac3 Series Bedienungsanleitung

Korenix

Korenix JetNet 5428G Series Bedienungsanleitung

NETGEAR

NETGEAR FS526T - Switch Bedienungsanleitung

Korenix

Korenix JetNet 5710G Series Bedienungsanleitung

Automated Logic

Automated Logic ZN551 Betriebsanleitung

Cisco

Cisco ASR 1000 Series Bedienerhandbuch

EnGenius

EnGenius ESR-9710 Bedienungsanleitung

Cisco

Cisco 805 Series Bedienungs- und Sicherheitshinweise