Paramount Fitness Paralevel Installations- und Betriebshandbuch

Paramount

8175 W. Buckeye Rd.,

Phoenix, AZ 85043

Phone: (480) 893-7607

www.1Paramount.com

Paralevel

Automatic Water Leveler

Start Up Manual

Contents

Overview.................................1

Start Up..................................2

Winterization..........................4

Identify Paralevel Model..........5

Use New Float in Old Tank........6

Replacement Parts..................7

004-027-8886-00 R00

ECN_2361 PUB021523

USE ONLY PARAMOUNT GENUINE REPLACEMENT PARTS

Overview

System Design

The Paralevel is designed to control the water level in a swimming pool or spa. The “Posi-Click”

control makes adjusting the water level very easy. Four clicks (or one revolution) of the adjustment

wheel changes the water level by ¼”. The Paralevel uses “Smart Sensing”, eliminating rapid cycling

of the device even when the pool is being used. The balance line must be plumbed with 1½” pipe.

The water line can be plumbed with ½” or ¾” pipe. The Paralevel can also be plumbed with 1½”

pipe for overﬂow protection.

Paralevel Layout & Design Criteria

1. Paralevel should be level and plumb.

2. The Paralevel main housing is engraved with “TOP OF GUNITE/SHOTCRETE (BEAM)”. The top

of the Paralevel housing should be positioned at the same elevation as the pool shell, assuming

3” above ﬁnal water level.

3. Maximum water pressure is 80 psi.

4. The ﬁll rate at 50 psi is 120 gph / 2 gpm.

5. WARNING - Balance line and overﬂow line must be plumbed straight. Failure to keep the run

of pipe straight may cause an airlock.

Bad

USE ONLY PARAMOUNT GENUINE REPLACEMENT PARTS

Start Up

Installation Steps

1. Make sure the water supply line is turned off at the

valve.

2. Remove plugs.

• Use the Removal Tool to remove the 1 ½”

NPT Cap.

• Use a 3/8” socket extension to remove the

½” NPT Seal Plug (Fig. 1).

3. Turn on water supply line to ﬂush line for a couple

of minutes. Then shut it off.

4. Install the 1 ½” NPT Nut Retainer. Hand tighten

ONLY, even when using tool.

• Make sure that the Retainer Ring is installed

properly in the Retainer Nut. The retaining

piece with raised rounded center is inserted

facing the top of the retainer nut (Fig. 2).

• Use Removal Tool to install Nut Retainer.

Fig. 1 Seal Plug

1 ½"

NPT Cap

Retaining Ring top view with

raised rounded center

Retaining Ring bottom view

with sharper center

Fig. 2

Top View: Correct

position of Retaining

Ring inside Retainer Nut

with rounded center

exposed.

Bottom View: Correct

position of Retaining

Ring inside Retainer

Nut with sharper center

exposed.

USE ONLY PARAMOUNT GENUINE REPLACEMENT PARTS

5. Install the ½” NPT Flow Plug using a 3/8"

socket extension (Fig. 3).

6. Installing ﬂoat assembly

• Grasp the top of the Riser Tube. (Fig. 4)

• Start with ﬂoat half way on sleeve ad-

juster (Fig. 5)

• Position the end of the Riser Tube with

the o-ring inside the opening at the top

of the Nut Retainer. (Fig. 6)

• Turn the Riser Tube clockwise and wig-

gle until it drops into the Nut Retainer.

Too much downward pressure before

it sets into the opening of the Nut Re-

tainer will cause the ﬂoat assembly to

hang up. (Fig. 7)

• Press down on the top of Riser Tube

and twist clockwise ¼ turn or until it

stops (Fig. 8).

7. Adjustment procedure (standard 3” waterline

below beam)

• Turn on water supply at source fully.

The Paralevel has anti-water hammer

feature as part of its smart sensing. The

Paralevel works best at full pressure

• Fill the pool until the water level is just

below center of tile with less than 1” left

to ﬁll.

• Shut off and remove all auxiliary hoses.

Leave the Paralevel water supply on.

• Allow the water level to rise until the

Paralevel shuts off.

• Measure the water level from top of

beam or bottom of deck. Note the dif-

ference from desired water level

• Remove ﬂoat from housing or reach

down on one side pushing on the alter-

nately raised part of the ﬂoat.

• Turn the ﬂoat counter-clockwise one

revolution for every ¼” the pool needs

to rise and clockwise one revolution for

every ¼” the pool needs to lower .

Example: to raise the water level 1”, turn the ﬂoat

counter-clockwise four revolutions. (Fig. 9a & 9b)

Fig. 3

Seal Plug

1 ½"

NPT Cap

Fig. 4 Fig. 5

Fig. 6

End of

Riser Tube

Opening at top

of Nut Retainer

USE ONLY PARAMOUNT GENUINE REPLACEMENT PARTS

Winterization

You will need the items in the winterizing/pressure test kit part number 005-760-2911-00

and tool 004-627-5452-00.

1. Turn off the water to the Paralevel.

2. Remove the Paralevel ﬂoat assembly by grasping the top of the ﬂoat assembly (above the

adjustment wheel and while pushing down turn the assembly counter clockwise a quarter turn.

The ﬂoat assembly should then pull out. Next using the removal tool #10 on the Paralevel

exploded parts diagram (page 6), remove the Retainer Nut and Retainer Ring #19 and #20.

Next using a 3/8 inch socket wrench extension remove the Flow Plug and O-ring #17 and #18

on the Paralevel exploded parts diagram. (page 6)

3. Drain the water in the pool to below the opening for the equalizer line for the Paralevel. Place

the O-ring and Seal Plug #4 and #5 on the winterizing kit exploded parts diagram (page 7)

into the threaded hole that the Flow Plug was removed from.

Fig. 7 Fig. 8

Fig. 9a Fig. 9b

USE ONLY PARAMOUNT GENUINE REPLACEMENT PARTS

NOTE: If draining the pool down below the equalizer line is not practical, then blow out the

equalizer line at the pool side by using a test plug with a Schrader valve and an air compres-

sor, at the same time suck out the water from the water leveler canister.

4. Disconnect the water supply line at the house going to the Paralevel. Blow this line to the open-

ing where the Retainer Nut and O-ring were while using a wet/dry shop-vac placed directly over

the threaded opening where the Retainer Nut was removed from to collect the water blown into

the Paralevel housing. When the line is clear place the Cap Seal and Main seal #1 and #3 on

the winterizing kit exploded parts diagram (page 7) over this opening. It is recommend that

the disconnected water line at the house be taped shut or sealed when disconnected so insects

and debris don’t get in the line.

5. Keep all of the plugs gaskets and o-ring removed for winterizing for startup in the spring.

NOTE: the ﬂoat assembly will not need to be adjusted next spring as long as you do not turn the

adjustment wheel from its set position when removed.

6. Optional: pour some non-toxic anti-freeze in the water leveler canister.

Identify Paralevel Model

1. Turn off the water.

2. Grasp top of ﬂoat assembly, twist counter clockwise ¼ turn, and pull out.

Old Float New Float Old Tank New Tank

Fig. 10a Fig. 10b Fig. 11a Fig. 11b

Ribs

USE ONLY PARAMOUNT GENUINE REPLACEMENT PARTS

1. While holding the new ﬂoat, twist sleeve

counter clockwise until it comes out of the

ﬂoat.

2. Turn ﬂoat over and re-thread on sleeve with

ﬂat side up. Be careful not to cross-thread

(Fig. 12).

3. Compare the ﬂoat height on the sleeve to the

old ﬂoat. The new style ﬂoat will need to be

approximately 5/8” lower on the sleeve to

achieve a similar water level (Fig. 13).

4. Install in the housing and turn on the water

supply.

5. If the ﬂoat is off, shut off the water and re-

move the ﬂoat and turn in the direction in-

dicated on the ﬂat side of the ﬂoat to raise

the water level 1/8”, one half turn, or 2

posi-clicks. Follow the arrows on the ﬂoat

(Fig. 14).

6. If the ﬂoat is on, shut off the water and re-

move the ﬂoat and turn in the direction in-

dicated on the ﬂat side of the ﬂoat to raise

the water level 1/8”, one half turn, or two

(2) posi-clicks. Follow the arrows on the ﬂoat

(Fig. 14).

7. Repeat steps 5a or 5b until water level is

matched.

8. Check pool level after a few days to verify

correct set level.

Use New Float in Old Tank

Fig. 12

Fig. 13

Fig. 14

Arrows

USE ONLY PARAMOUNT GENUINE REPLACEMENT PARTS

Replacement Parts

No. Part Number Description No. Part Number Description

1 005-760-2901-XX Lid 12 Part of Item #24 Lower Lever

2 005-760-2915-XX Deck Ring 13 Part of Item #24 Link Lever

3 Housing 14 * Riser Tube

4 005-760-2911-00 Winterization/Pressure

Test Kit 15 * Snap Ring

* 1 ½" NPT Cap 16 Part of Item #24 O-Ring 2-011 Viton Dur 75

* Main Seal 17 * Flow Plug

* Cap Seal 18 Part of Item #24 O-Ring 2-020 EP70

* Seal Plug 19 * Retainer Nut

* O-Ring 2-020 EP70 20 * Retainer Ring

8 005-252-1541-00** Extension Kit 21 * Adjuster Sleeve

9 004-552-5452-00** Tool 22 * Float Body

10 004-760-2921-00 Start Up Kit B 23 005-761-2934-00** Extension 1"

11 Part of Item #24 Top Lever 24 005-762-2932-00 Linkage Replacement Kit

*Parts are not available separately

**Not part of Paralevel. Order Separately.

Paralevel B

004-760-2902-XX

USE ONLY PARAMOUNT GENUINE REPLACEMENT PARTS

No. Part Number Description No. Part Number Description

1 005-760-2901-XX Lid 12 Part of Item #24 Lower Lever

2 Deck Ring 13 Part of Item #24 Link Lever

3 Housing 14 * Riser Tube

4 005-760-2911-00 Winterization/Pressure

Test Kit 15 * Snap Ring

* 1 ½" NPT Cap 16 Part of Item #24 O-Ring 2-011 Viton Dur 75

* Main Seal 17 * Flow Plug

* Cap Seal 18 Part of Item #24 O-Ring 2-020 EP70

* Seal Plug 19 * Retainer Nut

* O-Ring 2-020 EP70 20 * Retainer Ring

8 Extension Kit 21 * Adjuster Sleeve

9 004-552-5452-00** Tool 22 * Float Body

10 004-760-2921-00 Start Up Kit B 23 005-761-2934-00 Extension 1"

11 Part of Item #24 Top Lever 24 005-762-2932-00 Linkage Replacement Kit

*Parts are not available separately

**Not part of Paralevel. Order Separately.

Paralevel A

004-760-2900-XX

USE ONLY PARAMOUNT GENUINE REPLACEMENT PARTS

No. Part Number Description

005-760-2901-00 Winterization/Pressure Test Kit

1½" NPT Cap

2 Main Seal

3 Cap Seal

4 Seal Plug

5 O-Ring 2-020 EP70

Paralevel Winterizing/Pressure Test Kit

005-760-2911-00

USE ONLY PARAMOUNT GENUINE REPLACEMENT PARTS

Andere Handbücher für Paralevel

Inhaltsverzeichnis

Andere Paramount Fitness Wasserfiltersystem Handbücher

Paramount Fitness

Paramount Fitness Clear 03 Bedienungsanleitung

Paramount Fitness

Paramount Fitness MDX-R3 Programmierhandbuch

Paramount Fitness

Paramount Fitness MDX2 retro Bedienungsanleitung

Paramount Fitness

Paramount Fitness clear o3 Bedienungsanleitung

Paramount Fitness

Paramount Fitness clear o3 Bedienungsanleitung

Paramount Fitness

Paramount Fitness Clear 03 Bedienungsanleitung

Paramount Fitness

Paramount Fitness ClearO3 Bedienungsanleitung

Paramount Fitness

Paramount Fitness UltraUV Gebrauchs- und Pflegehandbuch

Paramount Fitness

Paramount Fitness SDX 2 Bedienungsanleitung

Paramount Fitness

Paramount Fitness Ultra UV2 Installationsanleitung

Beliebte Wasserfiltersystem Handbücher anderer Marken

Wisy

Wisy LineAir 100 Bedienungsanleitung

Schaffner

Schaffner Ecosine FN3446 Series Betriebsanleitung

Pentair

Pentair FLECK 4600 SXT Benutzerhandbuch

H2O International

H2O International H20-500 Bedienungsanleitung

Renkforce

Renkforce 2306241 Bedienungsanleitung

Neo-Pure

Neo-Pure TL3-A502 Bedienungsanleitung

FLTR

FLTR OBF Bedienungsanleitung

STA-RITE

STA-RITE VERTICAL GRID DE FILTERS S7D75 Bedienungsanleitung

Applied Membranes

Applied Membranes W-G844EM Bedienungsanleitung

BEGA

BEGA 116 Bedienungsanleitung

WATA

WATA Standard Bedienungsanleitung

Price

Price FFU series Handbuch

Gaggenau

Gaggenau BRITA INTENZA 467873 Bedienungsanleitung

Brita

Brita SAFF-100 Bedienungsanleitung

HEISSNER

HEISSNER FPU24000-00 Bedienungsanleitung

BGS technic

BGS technic 1518 Bedienungsanleitung

Reverse Osmosis

Reverse Osmosis RF Series Bedienungsanleitung

ubbink

ubbink Filtramax Series Bedienungsanleitung