Parker H Series Bedienungsanleitung
Effective: July 2018 IPDE-IOM-NEEDLE-VALVE-BALL-VALVE
Effective: REV A : July 2023
Installation and Operation Manual
Needle Valves & Ball Valves
Note - These Instructions apply to Parker Products that utilise Needle and Ball Valves such
as the ones shown above
Page 1 of 7
ECO-0438955
REV:A
Installation and Operation Manual
Needle Valves & Ball Valves
Parker Hannifin
Parker Hannifin (IPDE)
Riverside Road, Barnstaple, Devon, EX31 1NP United Kingdom
Telephone: (01271) 313131
E-mail: [email protected]
IDENTIFICATION OF HAZARDS
NEVER adjust valves under pressure.
NEVER slacken or remove any valve parts under pressure.
NEVER use any mechanical aids i.e. wrenches, extensions to operate handles.
NEVER carry ball valves by the handle.
NEVER obscure valve body marking.
NEVER remove end connectors.
INSTALLATION
Wear suitable PPE before installation and follow appropriate site safety procedures.
Before installation, ensure that all valves are in the closed position.
H Series Manifolds & Needle Valves:
Needle valves supplied with weld connections will generally be supplied, unless specified and/or
agreed with customer, fully assembled. Prior to welding Parker recommend removing the Head
Assembly from the body to protect from heat. The valve body should be welded into the system
following the appropriate welding procedures. To prevent ingress of foreign contaminants into the
valve body, the Head Assembly hole and thread must be protected. After welding the Head Assembly
can be reassembled into the valve body:
1. Ensure the spindle is fully retracted by holding the valve head unit and turning handle (1)
counter clockwise until stop if felt.
2. Place stainless steel washer (8) into body recess at the top of the body thread. Apply suitable
lubricant to stainless steel thread (6) prior to assembling the valve head to the body.
3. Tighten bonnet hexagon (6) into valve body to 108Nm (6000 Psi / 414 Bar) Standard Head
Assembly *
122Nm (10,000 Psi / 689 Bar) High Pressure Head Assembly - Designated HP *
* Note - Monoflanges use Standard Head Assembly and Pro-Bloc use High Pressure Head
Assembly.
4. Place rolled locking pin into the nearest one of the 2 Ø3mm holes to the bonnet hexagon and
insert until fully located.
Hi-Pro Ball Valve:
Care should be taken to ensure that the end connector (1) is firmly held by an appropriate spanner /
wrench (size varies depending on size of valve) to prevent any movement when assembling or
disassembling pipe or tube connections.
Flanged Products:
Refer to the appropriate installation standard for the flange specification in question.
Page 2 of 7
ECO-0438955
REV:A
Installation and Operation Manual
Needle Valves & Ball Valves
NPT: Use standard practice for NPT taper threads. Use an appropriate thread tape or sealant to
prevent galling.
A-lok/CPI: See separate instruction sheet supplied with A-lok products. For full instruction and best
practice on fabrication and installation of tube and A-lok/CPI tube fittings, scan the QR code below. *
When fitting A-lok/CPI, care should be taken to ensure that the end connector (1) (fig1) is firmly held
by an appropriate spanner / wrench (the size varies depending on the size of valve) to prevent any
movement when assembling or disassembling pipe or tube connections.
O-Lok: Take care to not damage the captive O-ring. For full instructions on O-lok assembly and
installation, please refer the O-lok section on page 55 of our Tube Assembly Guide which can be
found by scanning the QR link below. *
*For text versions of these QR codes, please See ‘Further Information’ at the end of this guide.
HANDLING AND STORAGE
Handling
Parker Products that utilise Needle and Ball Valves may be heavy. Ensure that local manual handling
requirements are followed.
Do not lift or carry by the operating handles, as this may cause damage.
Storage
There is no specified shelf-life.
Boxed products should be stored in a covered area, preferably indoors, and away from excessive
moisture, heat, or airborne contaminants.
The use of desiccant or corrosion inhibitors is not required during normal storage periods.
Page 3 of 7
ECO-0438955
REV:A
Installation and Operation Manual
Needle Valves & Ball Valves
OPERATION
H Series Screwed Head/Bonnet:
To close: Rotate the handle (1) Clockwise until a positive stop is felt up to a maximum torque of 6Nm.
To open: Rotate the handle (1) Counter Clockwise until the backstop is located. The valve will be in its
fully open position after approximately 3 turns of the handle
H Series Outside Screw & Yoke Head:
To close: Rotate the handle (1) Clockwise until a positive stop is felt up to a maximum torque of 6Nm.
To open: Rotate the handle (1) Counter Clockwise until the backstop is located. The valve will be in its
fully open position after approximately 3 turns of the handle.
Page 4 of 7
ECO-0438955
REV:A
Installation and Operation Manual
Needle Valves & Ball Valves
Hi-Pro Ball Valve:
To close: Operate the handle (17) until it is at 90° from the valve body centreline.
To open: Operate the handle (17) until it is in line with the centreline of the body and reaches the stop
pin.
Movement is limited to 90° by a mechanical stop pin.
Ball valves should always be fully open or fully closed. Do not leave in a mid-position.
Page 5 of 7
ECO-0438955
REV:A
Installation and Operation Manual
Needle Valves & Ball Valves
MAINTENANCE
H Series Screwed Head/Bonnet:
CAUTION: Adjustment of the gland must be carried out at zero pressure
1. Fully close the valve by turning the handle (1) in a clockwise direction to stop lightly on seat
2. (max. 2 Nm).
3. Open the valve one full turn by rotating the handle (1) in a counter clockwise direction.
4. Loosen gland lock nut (4).
5. Tighten gland nut (3) to 11 Nm
6. Re-tighten gland lock nut (4) to 25 Nm.
Page 6 of 7
ECO-0438955
REV:A
Installation and Operation Manual
Needle Valves & Ball Valves
H Series Outside Screw & Yoke Head:
CAUTION: Adjustment of the gland must be carried out at zero pressure
1. Fully close the valve by turning the handle (1) in a clockwise direction to stop lightly on seat
(max. 2 Nm).
2. Open the valve one full turn by rotating the handle in a counter clockwise direction.
3. The two bridge-nuts (3) on either side of the spindle must be tightened evenly, keeping the
bridge parallel to the body, to a torque of 5Nm.
Hi-Pro Ball Valve:
Parker Hi-Pro Ball Valves are not user-serviceable.
Page 7 of 7
ECO-0438955
REV:A
Installation and Operation Manual
Needle Valves & Ball Valves
FURTHER INFORMATION
Dust Cap colours on Needle Valves signified below:
Ball Valve Cv values:
10mm bore: 6.4
15mm bore: 15
20mm bore: 31
25mm bore: 39
Needle Valve Cv values
Bar Stock Needle valves: 0.35
Bar Stock Needle valves with 6mm bonnet seats: 0.5
Rising plug valves: 1.8
(Note, these are generic values for our range and may vary for specific items/connections. If in doubt,
please contact our technical support)
Text versions of QR codes
https://qr.parker.com/203785 Tube Fitting Installation Manual (A-lok/CPI)
https://qr.parker.com/203784 Tube Assembly (O-lok: please refer to page 55)
Technical Support: [email protected]m
Andere Handbücher für H Series
2
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere Parker Steuereinheit Handbücher
Parker
Parker DINCon II Montageanleitung
Parker
Parker EBV-PR Series Benutzerhandbuch
Parker
Parker EP Series Pro-Bloc Bedienungsanleitung
Parker
Parker Vansco VMM1210 Bedienungsanleitung
Parker
Parker CK-6D Leitfaden
Parker
Parker 930 Series Leitfaden
Parker
Parker PIO-400 Bedienungsanleitung
Parker
Parker Vansco Bedienungsanleitung
Parker
Parker RE06M T Series Bedienungsanleitung
Parker
Parker TPQ Series Bedienungsanleitung
Parker
Parker C2 Series Montage- und Wartungsanleitung
Parker
Parker DxFB Series Bedienungsanleitung
Parker
Parker HASV08R Bedienungsanleitung
Parker
Parker S5A Leitfaden
Parker
Parker C10 Bedienungsanleitung
Parker
Parker CK4A-DN Bedienungs- und Montageanleitung
Parker
Parker S5A-DN Bedienungs- und Montageanleitung
Parker
Parker S7A Service-Handbuch
Parker
Parker S4A-DN Bedienungs- und Montageanleitung
Parker
Parker 2B4 Series Bedienungsanleitung
Beliebte Steuereinheit Handbücher anderer Marken
Festo
Festo Compact Performance CP-FB6-E Stücklistenhandbuch
Elo TouchSystems
Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung
JS Automation
JS Automation MPC3034A Bedienungsanleitung
JAUDT
JAUDT SW GII 6406 Series Kurzanleitung
Spektrum
Spektrum Air Module System Bedienungsanleitung
BOC Edwards
BOC Edwards Q Series Bedienungsanleitung
