Parkside PSS 310 Bedienungsanleitung
PSS 310
2003
4 manual GB (+IRL)_Helv 17.06.2003 14:21 Uhr Seite 1
Kompernaß Handelsgesellschaft mbH
Burgstraße 21 · D-44867 Bochum Germany)
4 manual GB (+IRL)_Helv 17.06.2003 14:21 Uhr Seite 2
4 manual GB (+IRL)_Helv 17.06.2003 14:21 Uhr Seite 3
PSS 310 ORBITAL SANDER
For effortless sanding of metal, wood and varnish/paint …
Dear Customer! We are delighted that you have decided to purchase our high quality PSS 310 orbital sander.
Please make sure you familiarise yourself fully with the way the equipment works before you use it for the first
time and that you understand how to handle electrical power tools correctly. Please read the operating
instructions below and the accompanying safety advice carefully. Use the equipment only as
described and for the indicated purposes. By doing this you will be able to work in complete safety and produce
better results. We hope you enjoy using your sander.
PROPER USE
The orbital sander is intended for sanding wood, metal and paint. Always use a sanding sheet and grade that are
suitable for the particular surface you are sanding. The speed selected should also be appropriate.
FEATURES OF THE PSS 310
Clip Handle
Sanding sheet ON / OFF switch
Base Adjuster wheel
Air vents Dust extraction nozzle (Fig.)
Dust bag adapter ,,,= accessories supplied
Paper dust bag
TECHNICAL INFORMATION
Nominal power: 310 W Nominal voltage: 230 V ~ 50 Hz
Low load speed: n 7,000 – 11,000/min Dust extraction system: built-in extraction system /
Orbits: max. approx. 22,000/min or with exterior suction device
Pad size: 225 x 115 mm Weight: 2.25 kg
Orbit: 2.1 mm
Sanding sheet size max: approx.: 280 x 115 mm The A weighted noise level of the equipment is
Protection class: II typically:
Sound pressure level: 70.0 dB(A)
The acceleration value is typically 2.5 m/s2(vibration)
IMPORTANT SAFETY ADVICE
• To be read in conjunction with the advice in the accompanying booklet on safety.
• The sander is not designed for wet sanding and therefore is only to be used for dry sanding
• Do not use the sander on materials containing asbestos
• Look after your health: Wear ear defenders - also wear safety glasses and a breathing /dust mask
• Take note that working with stone and wood can give rise to dusts that can damage your health.
• Always keep the power cable well out of the sander's working area and fed to the rear of the machine.
!
!
4
www.kompernass.com +++ www.kompernass.com +++ www.kompernass.com +++ w
o
4 manual GB (+IRL)_Helv 17.06.2003 14:21 Uhr Seite 4
OPERATION
Take note of the mains voltage. The voltage must agree with that shown on the identification plate (equipment
shown as 230 V can also be used with 220 V).
SWITCHING ON AND OFF
SWITCH ON SANDER = press switch
SWITCH OFF SANDER = press switch again
SETTING THE SPEED
You can set the required speed using the adjuster wheel (see Fig ) as required. As the setting depends on
what kind of material you are working with, use the recommendations and examples given in Tips and Tricks.
FITTING THE SANDING SHEETS
Note: before fitting a new sanding sheet, remove dust and dirt from the base .
1. Lift both clips to open them to insert a new sanding sheet or change the sanding sheet for
use on a different material.
2. Push the sanding sheet under the open clip at one end and clamp it securely on the base by
moving the clip down again.
3. Do the same at the other end. Make sure that the sanding sheet is tight against the base. See Figures and .
4. Important! - The holes in the sanding sheet and the base must align for the dust to be extracted through the
base. See Figure .
Different materials need different grades of sanding sheets. To determine which grade is suitable for your work,
please read our recommendation in Tips and Tricks.
DUST EXTRACTION
• DUST EXTRACTION WITH PAPER DUST BAG
Push the paper dust bag on to the adapter . Ensure that the adapter fits correctly into the holder.
Clip the dust bag with the adapter to the side of the sander.
• DUST EXTRACTION WITH VACUUM CLEANER
For dust extraction using a vacuum cleaner use the appropriate connector – see Figure . Attach the adapter to
the end of the vacuum cleaner hose and clip it to the side of the equipment.
MAINTENANCE OF THE ORBITAL SANDER
1. Clean the sander regularly. For the best results do this straight after the work has been completed.
2. Do not allow liquids to get inside the sander. Use a soft cloth for cleaning the housing. Do not use petrol,
solvents or cleaners that may attack the plastic.
3. Air vents must always be clear and clean.
5
+ www.kompernass.com +++ www.kompernass.com +++ www.kompernass.com +++
4 manual GB (+IRL)_Helv 17.06.2003 14:21 Uhr Seite 5
w
ADVICE ON WORKING METHODS, TIPS AND TRICKS
• You can use the PSS 310 orbital sander for effortless sanding even on large areas, see Fig. .
• Move the orbital sander in parallel broad circles or in alternate longitudinal and transverse directions.
• Do not press on the orbital sander. This damages the sanding sheets and adversely affects sanding performance.
• From time to time clean the sanding sheet with a vacuum cleaner.
• You do not have to resand any areas when working up to edges. The orbital sander works right into the corners
because its housing is continuous with the edge of the sanding sheet, see Fig. .
• The integrated dust extraction system allows you to work cleanly overhead. Use the integrated dust extraction
system or your vacuum cleaner wherever possible when sanding.
• The choice of speed and grade of sanding sheet determines the sanding performance and therefore the results
of your work.
• Never use the same sanding sheet on different materials (e.g. wood and then metal).
•* For metals we recommend 60 grade (steel) or 80 grade (aluminium) – with a medium to high speed.
•* For wood we recommend 60 grade (hardwood) or 60 – 80 grade (soft wood) with a medium to high speed. If you
are sanding veneered surfaces we recommend 240 grade – with a low to high speed depending on the
smoothness of the finish.
•* When working on varnished/painted surfaces we recommend 120 grade e.g. for smoothing out scratches
(medium to high speed), 180 grade for sanding down (low speed) and 40 grade e.g. for removing rust
(low to middle speed).
• The PSS 310 orbital sander uses HIGH TECHNOLOGY FIXING.
This no-tool quick change feature allows you to work more easily
and quickly. One hand is all that is needed.
•* These are advisory recommendations only. Before you start work, you should carry out a test to see which grade
and speed is most suitable for your work.
Further practical tips for power tools can be found in the accompanying booklet on safety advice.
We reserve the right to make technical modifications in the course of further development.
6
www.kompernass.com +++ www.kompernass.com +++ www.kompernass.com +++
4 manual GB (+IRL)_Helv 17.06.2003 14:21 Uhr Seite 6
www.kompernass.com +++ www.kompernass.com +++ www.kompernass.com +++
STATEMENT OF CONFORMITY
We, Kompernaß Handelsgesellschaft mbH, Burgstr. 21, D-44867 Bochum, Germany, hereby declare
that this product conforms with the following EC regulations:
(98/37 EWG)
EC low voltage regulations: (73/23/EEG), (93/68 EEG)
Electromagnetic compatibility: (89/336 EEG), (92/31 EEG), (93/68 EEG)
Applicable harmonised standards:
Type: Orbital sander PSS 310
Bochum, 31.05.2003
Hans Kompernaß
- Managing Director -
7
+
4 manual GB (+IRL)_Helv 17.06.2003 14:21 Uhr Seite 7
8
WARRANTY
This piece of equipment is covered by a 3-year warranty as of the date of purchase. The equipment was produced
with the greatest of care and underwent thorough testing before delivery. In the unlikely event of detecting a
functional defect, please return the equipment in its original packaging with the proof of purchase to the closest
service address. Damage caused due to improper handling as well as regular wear of the parts are not covered by
this warranty.
Beaver Electronic Services · The Lodge, Premier Business Park
Long Street, Walsall · West Midlands, WS2 9DY
Tel.: 08707876177 · Fax: 01922/725417
WARRANTY
This piece of equipment is covered by a 3-year warranty as of the date of purchase. The equipment was produced
with the greatest of care and underwent thorough testing before delivery. In the unlikely event of detecting a
functional defect, please return the equipment in its original packaging with the proof of purchase to the closest
service address. Damage caused due to improper handling as well as regular wear of the parts are not covered by
this warranty.
Irish Web Specialists · 1 Verbena Avenue · Dublin 13
Tel.: 01/8320492 · Fax: 01/8396829
4 manual GB (+IRL)_Helv 17.06.2003 14:21 Uhr Seite 8
9
www.kompernass.com
© manual design, photos, translations by
ORFGEN Marketing & Communication
Essen · Germany
4 manual GB (+IRL)_Helv 17.06.2003 14:21 Uhr Seite 9
www.kompernass.com
© manual design, photos, translations by
ORFGEN Marketing & Communication
Essen · Germany
4 manual GB (+IRL)_Helv 17.06.2003 14:21 Uhr Seite 10
Inhaltsverzeichnis
Andere Parkside Sander Handbücher
Parkside
Parkside PEXS 270 A1 - 3 Bedienungsanleitung
Parkside
Parkside PSS 250 A1 Bedienungsanleitung
Parkside
Parkside XQ 600 - MANUAL 2 Kurzanleitung
Parkside
Parkside PEXS 270 A1 Bedienungsanleitung
Parkside
Parkside PWP 90 A1 POLISHING MACHINE Bedienungsanleitung
Parkside
Parkside PDS 290 A1 Bedienungsanleitung
Parkside
Parkside PDEXS 150 A1 Bedienungsanleitung
Parkside
Parkside PAAP 12 A1 Bedienungsanleitung
Parkside
Parkside 365102 2101 Bedienungsanleitung
Parkside
Parkside PSS 250 - MANUEL 2 Bedienungsanleitung
Parkside
Parkside PWP 90 A1 POLISHING MACHINE Bedienungsanleitung
Parkside
Parkside PHS 160 E5 Bedienungsanleitung
Parkside
Parkside PHS 160 D4 Bedienungsanleitung
Parkside
Parkside PWDS 920 A1 Kurzanleitung
Parkside
Parkside 364419 2010 Bedienungsanleitung
Parkside
Parkside PPS 200 A1 Bedienungsanleitung
Parkside
Parkside PDS 290 A1 Bedienungsanleitung
Parkside
Parkside PSS 250 Bedienungsanleitung
Parkside
Parkside PAHS 12 A1 Bedienungsanleitung
Parkside
Parkside 273101 Bedienungsanleitung
