Paslode TrimMaster IM250A-Li Bedienungsanleitung

IMPORTANT!

DO NOT DESTROY

It is the customer's responsibility to have

all operators and service personnel read

and understand this manual.

OPERATING MANUAL

Part No. 902400

Model IM250A Li

CORDLESS 16 GAUGE

ANGLED LITHIUM-ION

FINISH NAILER

Introduction

For ease of use, this manual is divided into sections (see

Contents). Each section of the manual is written with you,

the tool operator, in mind. We have left out many of the

technicaltermssothatyoucaneasilyunderstandhowtoget

themaximumperformancefromyourCordlessFinishNailer,

andhowtoavoiddamagingthetoolorinjuringyourself.But,

to accomplish this, we need you to do two things:

1.READTHE MANUAL FROM COVERTO COVER

BEFORE USINGTHETOOL.

2.FOLLOW ALL INSTRUCTIONS INTHE MANUAL.

The Cordless Finish Nailer should be handled like other

powerfasteningtoolsthatyouuse.Likemosttools,when

used improperly injury could result . If you are going to

allow others to use the Cordless Finish Nailer, it is your

responsibilitytomakesurethattheyalsoreadandcomply

with the instructions in this manual before attempting to

operate the tool.

This manual is intended to acquaint you with the Paslode

Cordless 16 ga. Angled Lithium-ion Finish Nailer. Unlike

other power fastening tools, the Cordless Finish Nailer is

terms, your Cordless Finish Nailer is powered by a motor

similar to the one that powers an automobile. The Cord-

less Finish Nailer ignites a fuel and air mixture to produce

the energy to drive the motor, which in turn drives the

fastener. The Cordless Finish Nailer is totally

self-contained. It carries its own fuel supply and battery,

along with a supply of fasteners.

Paslode Cordless 16 Gauge Angled

Lithium-ion Finish Nailer Operating

Manual

Description

Inorderforyoutofullyunderstandtheinformationcontained

in this manual, you need a basic understanding of the

Cordless Finish Nailer. As you can see in the illustration

below,the Cordless FinishNailer ismadeup of threemajor

areas: handle, motor, and magazine.

AsyouexaminetheCordlessFinishNailer,becomefamiliar

with the three major areas and the various components

located in each of them.

The Handle Assembly containsthe fuel cartridge, indicator

light, and the trigger.

TheMotorAssemblycontainsthecoverandﬁlter,themotor

housing, the nose, and the work contacting element.

TheMagazineAssembly

daolotstnenopmocehtsniatnoc

and control the fastener and the battery for the Cordless

Finish Nailer.

Speciﬁcations

Dimensions: Weight-with battery 4 .6 lbs

Height 11-1/2 inches

Length 10-3/4 inches

Magazine Angled

(use Paslode angled fasteners only.)

Cycle Rate: Intermittent Operation – 2 to 3 nails

per second

NOTE: Exceeding these cycle rates could cause the tool

to overheat, resulting in loss of performance or damage to

tool components.

Fasteners: 16 Gauge Angled

Magazine

Capacity: 2 nail strips, or 100 fasteners.

Battery : 7.4voltsDC-

Provides enough

energy to

drive

approximately 6000

fasteners on a

full charge.

Fuel

Cartridge:

Trim fuel cartridge

(.64oz) Part

#816007

Liquid hydrocarbon - Provides

enough

fuel

to drive approximately 1000 fasteners.

Magazine Assembly

fuel cartridge compartment

cap

removable

grille & ﬁlter

no-mar tip

Handle Assembly

(soft grip)

soft

touch

trigger

Motor

Assembly

battery compartment

(opposite side)

battery indicator light

(opposite side)

follower

motor housing

nail count indicator

lockout

feature

adjustable

depth of drive

(opposite side)

quick clear

cover

rafter/belt hook

The Paslode Cordless

16 ga. Angled Lithium-ion Finish

Nailer is a self-contained, fully portable nailer that uses

liquid hydrocarbon fuel to power a unique linear drive

internal combustion motor.

Overview of the Paslode Cordless

16 Gauge Angled Lithium-ion Finish Nailer

By using the Paslode Cordless 16 ga. Angled Lithium-ion

Finish Nailer at its recommended cycle rate, you will be

able to drive several thousand nails in a typical workday.

Safety Instructions

DANGER

WARNING

Do not expose the tool to

temperaturesinexcessof

120° F (49° C). Fuel and/

or the battery may burst,

releasing ﬂammable gas.

WARNING

The following safety instructions have been included in

this booklet to provide you with basic information neces-

sary for safe operation of the Paslode Cordless 16 ga.

Angled Lithium-ion Finish Nailer.

DO NOT ATTEMPT TO OPERATE THIS TOOL UNTIL

YOU HAVE READ AND UNDERSTAND ALL SAFETY

PRECAUTIONS AND MANUAL INSTRUCTIONS.

The Cordless Finish Nailer

is an internal combustion

device. It produces hot

exhaust gases that may

ignite ﬂammable materials.

This tool must not be used

in a combustible environ-

ment or in the presence of

combustible materials,

such as ﬂammable chemi-

cals, adhesives, gasoline,

or solvents.

Do not attempt to operate

this tool until you have read

and understood all safety

precautions and manual

instructions.

Failure to follow all safety

precautions and instruc-

tions may result in a perma-

nent loss of vision, serious

personal or even fatal

injury, property damage

and/or tool damage.

This tool must be operated

only in a well-ventilated

environment, because

the tool exhausts carbon

monoxide similar to a gas

chainsaw or lawnmower.

Exposure to carbon mon-

oxide may cause dizzi-

ness, nausea, or uncon-

sciousness.

ALWAYS keep the Cordless

Finish Nailer, fuel cartridge,

battery and battery charger

out of the reach of children.

Safety Instructions

WARNING 7. NEVER OPERATE THE TOOL WITH THE

WORK CONTACTING ELEMENT REMOVED OR

DISABLED.

This device helps reduce the possibility of accidental

fastenerdischargebypreventingthetoolfromoperating

until it is completely against the work surface.

NEVER operate the tool if the work contacting element

is not working properly.

Pull the follower slightly back and push the release

lever.Tipthe tool noseupslightlyand fasteners should

slide out of the rear of the magazine. If fasteners are

jammed, refer to the appropriate servicing section of

this manual.

9. NEVEROPERATETHECORDLESSFINISH NAILER

IF PARTS ARE LOOSE, DAMAGED OR MISSING.

10. DO NOT DRIVE FASTENERS INTO KNOTS OR ON

TOP OF OTHER FASTENERS.

A fastener may ricochet and cause serious injury.

11. OPERATE THE TOOL ONLY ON THE WORKPIECE.

1. Eye protection must meet the requirements of ANSI

Standard Z87.1 and should have side shields for

increased protection.

2. NEVER ASSUME THE TOOL IS EMPTY.

Never point the tool at yourself or anyone else.

3. NEVER ENGAGE IN "HORSEPLAY" WITH THE

TOOL.

The Cordless Finish Nailer is not a toy – it is a tool.

Careless and improper use may result in a serious

accident.

4. NEVERCARRYTHETOOLWITHYOURFINGERON,

OR SQUEEZING, THE TRIGGER.

This practice may result in the accidental discharge of

a fastener.

5. NEVER OPERATE A MALFUNCTIONING TOOL.

Refer to the servicing or troubleshooting section of this

manual to correct the problem. If the problem cannot

be corrected, stop using the tool and report it to your

supervisor or Paslode®representative.

6. DO NOT LOAD FASTENERS WITH THE TRIGGER

AND/ORWORKCONTACTINGELEMENTPRESSED

IN.

A fastener may be accidentally discharged.

WARNING

TheCordlessFinishNailer

should be operated only

when it is in contact with

the work surface. When

fastening thin materials

such as plywood, be sure

toposition the toolsothat

the fastener is driven into

the underlying piece.

ALWAYS POINT THE TOOL AWAY FROM YOUR-

SELF AND OTHERS WHEN CLEARING A JAM OR

REMOVING FASTENERS.

Always wear EYE and EAR

safety gear when working

with or in the vicinity of the

Paslode Cordless 16 ga.

Angled Lithium-ion Finish

Nailer.

Safety Instructions

12. NEVER DRIVE FASTENERS INTO AREAS WITH

CONCEALED HAZARDS.

Always check the area behind the work surface for

electrical wiring, gas pipes, water pipes, sewer drains

or other potential hazards.

13. ALWAYSMAINTAINSECUREANDUNOBSTRUCTED

FOOTING WHEN ON LADDERS, PLATFORMS OR

OTHER HIGH LOCATIONS.

14.ALLOWONLYQUALIFIEDPERSONNELTOOPERATE

THE CORDLESS FINISH NAILER.

15. PROPERLY STORE FUEL CELL.

16.ALWAYSSTORETHETOOLWITHTHEFUEL

CARTRIDGE AND BATTERY REMOVED.

17. KEEP THE TOOL CLEAN.

A clean tool is less likely to jam or malfunction.

18. KEEP YOUR HANDS CLEAR OF THE WORK AREA

SURFACE.

WARNING

Never over-reach, since

tool recoil may cause a

loss of balance. Always

dnasegdefoerawaeb

drop-offs when nailing on

rooftops and other high

locations. Keep them in

full view.

WARNING

Only persons who have

readandfullyunderstand

all tool operation, safety

and maintenance

instructions should be

allowed to operate the

tool.

WARNING

A fastener may exit at an

angle unexpectedly and

cause injury.

WARNING

Battery Disposal:

IMPORTANT SAFETY INSTRUCTIONS!

SAVETHESE INSTRUCTIONS!

DANGER

TO REDUCE THE RISK OF FIRE OR

ELECTRIC SHOCK, CAREFULLY

FOLLOW THESE INSTRUCTIONS

CHARGING SYSTEM SAFETY

INSTRUCTIONS!

The Paslode batteries contain lithium and should be

recycled or disposed of properly. It is illegal in some

areas to place a lithium battery into the trash or solid

waste stream.

Always store fuel cartridges

where they will not be

exposed to an open ﬂame,

sparks or temperatures

above 120° F (49° C).

Store the fuel cartridge in the case with the cordless

finish nailer

For connection to a supply outside North

America, use an attachment plug adapter

of the proper configuration for the power

outlet, if needed.

Warning

CHEMICAL/EXPLOSION

HAZARD

Read ALL instructions be-

fore charging or using bat-

tery. Failure to follow ALL

instructions may result in

ﬁre, severe burns, or re-

lease of toxic materials.

Battery and Charging System

Charging Instructions

2. Remove the battery from tool or case and insert ter-

minals down into charger. The red light will come on

indicating that the battery is charging and the green

light will go out.

3. After charging is complete, the red light will go out

and the green light will come on, indicating that the

battery is fully charged. The charger will keep the

battery at full charge until it is removed.

4. Unplug the charger from the 120V AC outlet.

CHARGINGTIMES:

First charge (new battery) 1 hour

Discharged Battery 5 minutes to 1 hour

CHARGING DON'TS:

1. Do not charge battery outdoors or in temperatures

below 40°F (5°C).

2. Do not allow metal objects to come in contact with

battery terminals.

3. Do not puncture or attempt to open battery case or

cells.

4. Do not store battery where it will be subjected to

temperatures above 120°F (49°C).

5. Do not incinerate battery.

6. Do not use a defective battery charger, one that

over-heats and/or smokes when plugged in.

7. Do not immerse the battery or charger in water.

Charging System Accessories:

Battery Charger - Part No. 902672

Note

Battery and Charging System

Important Charging Notes

Removethe charger unit from the tool case and plug

it into a 120V AC outlet. Set the charger base on a

stable surface. A green light will come on to indicate

the power is on and the charger circuit is ready.

If battery is completely discharged, the red light and

the green light may alternate back and forth for up to

20 minutes. This safety feature slowly recharges the

battery until it is ready to accept the full charging

current. If the red and green lights continue to alter-

nate after 20 minutes, replace the battery.

The Paslode Cordless 16 Gauge Angled Lithium-ion

Finish Nailer comes with a rechargeable battery and

its own charging system. This charging system is

the only one that will work with the Paslode

lithium-ion batteries. The ﬁrst step in preparing a

new tool for operation is to fully charge the battery.

New batteries are shipped partially discharged

and must be charged prior to ﬁrst use. Batteries

will take 5 minutes to 1 hour (time will be dependant

on the amount of discharge of the battery) to

recharge.

6ft. Cord

Battery

Charger

THE PASLODE BATTERY CHARGING SYSTEM

Battery and Charging System

Inserting Battery

1. hsiniFsseldroCehtotni,tsrﬁstcatnoc,yrettabehtdaoL

Nailer.

2. Push battery fully forward into its locked Ready

position. The battery indicator light will light.

NOTE: If battery is left in tool for an extended period,

the battery will discharge completely and will require

recharging.

Battery Indicator Light

Ontherightsideofthehandleisasmallplasticlens. Thisis

the battery indicator light. When you insert a fully-charged

battery into the tool, you will see a blinking green light. If

the indicator light blinks red, recharge the battery.

BATTERY INDICATOR LIGHT

CAR ONMOOXI E HZARD SON Y N E T A ED R A O VO DA S A ND UN ON CUNESS

ESINUEE T E MDD EPOL UN N R P C P U EN A N R EACETS

! XLO I NH Z RD E ERU E N E LO IV A MO H RE OOLE H U T OULD G T F MES

T L P TR N B S A D R MUTW R E E ND E R NG POTE T N T A COF RMS O ANSS AND R S

A OL S G AL M A LRU ER IS

! S UM T OLI A WA SOADDANDW LL A W YS RA F SN R

R D MANU L R M OV R OCO ER DI E ARD N WA N N S OLD R SLTI A C D NS

C R O MO O IDE A A D SEON Y IN E TI A E A EA O VO D NA S A ND N ON C U NESS

E SO N US E T L ODE D MPLO L UR N NR P C P U E TANRE A CE TS

E P O ON A A D E E U E N XL S V A MO H RE OOL H US OUL GTE U ES

T OP R T RA DB STAD RS MU T WE R EYE ND HE R G P O ET NT A CO F RMS OANS S AND R S

T D L S I A L M AL OC R R U S R IS

!AS U E OO IS A W YS O D D A D W L AW YS RA F S NER

EAD MNUALOM OVER OO ER I E A D N WAN N S O LD S LT I A C D NS

To remove battery, push down on locking tab and slide

battery out.

To disengage the battery, push down on locking

tab and slide battery back until it locks into the

Standby position.

Ready

Position

Standby

Position

DANGER

EX PLO SIO N/FI R E

HAZARD

WARNING

Sunlight can raise the inside temperature of an

unventilated car or van to above 140°F (60°C).

Never puncture or attempt to open the fuel cartridge;

it is non-reﬁllable.

Never incinerate, reclaim or recycle the fuel cartridge.

Neversmokewhileinstalling the fuel cartridge.

Never inhale the spray.

Keep out of the reach of children.

Store fuel cartridge(s) in well-ventilated areas only.

Fuel Cartridge

Toejectthefuel,propellantpressuresqueezestheinnerfuel

container, much as you squeeze a tube of toothpaste. This

squeezing action ensures that all the fuel is used, and that

the Cordless Finish Nailer can operate in any position.

Because of this container-within-a-container design, you

might hear the sound of ﬂuid when shaking the fuel cell

afterallthefuelhasbeenused.Thisisthepropellant,which

remains between the containers even after all the fuel has

been expelled.

Fuel Cartridge

NOTE

1. When replacing fuel cartridge also clean or replace

the air ﬁlter for optimum tool operation.

PaslodeCordlesstechnologyispoweredbyaninternal

combustionengineandareeffectedbyaltitude. The

toolmaylosepowerorbecomeerraticatelevationsof

NOTE: Altitude Restriction

6000 feet or greater.

There is a second container inside the fuel cartridge. The

inner container holds the fuel. The space between the

inner container and the outer cylinder is ﬁlled with a gas,

called the propellant, which is under pressure.

Read ALL safety

instructions before using

or handling the fuel

cartridge. Failure to

follow ALL instructions

may result in explosion or

ﬁre. This may cause

severe personal injuries

or property damage.

Keep the fuel cartridge

away from heat, sparks

and open ﬂame.

Exposure to tempera-

tures above 120°F

(49°C) may cause the

fuel cartridge to burst,

releasing flammable

gas.

If you expose the empty fuel cartridge to extreme

temperatures, the propellant gas will expand and could

cause the container to burst, releasing ﬂammable gases.

Fuel Cartridge

NOTE:

Paslode Cordless fuel cartridges are marked with a “Best Use Before” date on the bottom of the can.

For maximum performance use fuel before the“Best Use Before” date.

DANGER

Paslode Cordless Fuel Cartridges are flammable.

Do not remove fuel cartridge cap or install on other

fuel cartridges!

Paslode Cordless Fuel Cell/Cartridge Disposal Guidelines

Paslode the industry leader in cordless technology provides this information to assist users with the proper disposal of discarded

fuel cells/cartridges. Acceptable disposal options vary depending on the type of fuel cell/cartridge users. All users must cons

ider

federal, state and local solid waste regulations to ensure that discarded fuel cells/cartridges are disposed of properly. Users

must

contact their local solid waste authority for further guidance.

Discarded fuel cells/cartridges (used or unused) may be considered hazardous waste under the Resource Conservation and

Recovery Act (RCRA) depending on several factors as described in the paragraphs that follow. Upon disposal used and unused

fuel cells/cartridges may be classified as ignitable hazardous waste (waste code D001) under U.S. EPA regulations.

Hazardous waste generated by homeowners and contractors who perform routine maintenance for homeowners in their homes are

not regulated by RCRA. In general, "household wastes" generated by homeowners and their contractors are exempt from hazard-

ous waste regulation because those wastes are expressly excluded from the definition of hazardous waste. For example US EPA

has excluded as "household waste" aerosol cans that contain residual product and propellent. Thus under

federal hazardous waste

regulations homeowners and contractors may dispose of discarded fuel cells/cartridges as general refuse in a properly permitted

municipal landfill. These users must still contact their local solid waste authority to determine if any state or local regulation

prohibits or restricts such disposal.

Paslode takes no responsibility for proper fuel cell/cartridge disposal. Proper disposal remains the responsibility of sellers and

users. All sellers and users must contact their local solid waste authority to determine if any

federal, state or local regulation

prohibits or restricts disposal.

Andere Handbücher für TrimMaster IM250A-Li

Inhaltsverzeichnis

Andere Paslode Nagelpistole Handbücher

Paslode

Paslode T250S-F16P Bedienungsanleitung

Paslode

Paslode LL350S Bedienungsanleitung

Paslode

Paslode RINGfast A515 Bedienungsanleitung

Paslode

Paslode 916200 Bedienungsanleitung

Paslode

Paslode F250S-PP Bedienungsanleitung

Paslode

Paslode F250S-PP Bedienungsanleitung

Paslode

Paslode IM250S Li Handbuch

Paslode

Paslode IM250A Bedienungsanleitung

Paslode

Paslode 900600 Bedienungsanleitung

Paslode

Paslode 30 Degree Handbuch

Paslode

Paslode 575057 Bedienungsanleitung

Paslode

Paslode IM350+ Lithium Bedienungsanleitung

Paslode

Paslode PFS160 Bedienungsanleitung

Paslode

Paslode 3250-F16 Kurzanleitung

Paslode

Paslode IM350+ Lithium Bedienungsanleitung

Paslode

Paslode Cordless Framing Nailer Bedienungsanleitung

Paslode

Paslode IM200Li Bedienungsanleitung

Paslode

Paslode IMPULSE PPN-MASTER IM40 Bedienungsanleitung

Paslode

Paslode IM250A-Li2 Bedienungsanleitung

Paslode

Paslode CORDLESS 16 GAUGE ANGLED FINISH NAILER Handbuch

Paslode

Paslode T250-F16 Bedienungsanleitung

Paslode

Paslode F325R Bedienungsanleitung

Paslode

Paslode 360Xi Bedienungsanleitung

Paslode

Paslode F250S-PP Bedienungsanleitung

Beliebte Nagelpistole Handbücher anderer Marken

Performance Tool

Performance Tool M643 Bedienungsanleitung

Hitachi

Hitachi VH650 - Fencing Nailer, Full Head Bedienungsanleitung

Parkside

Parkside PET 25 B1 Bedienungsanleitung

Senco

Senco Fusion Technology F-35XP Bedienungsanleitung

Grizzly

Grizzly G1847 Bedienungsanleitung

Ryobi

Ryobi R18N18G Bedienungsanleitung

Black & Decker

Black & Decker 492848-00 Bedienungsanleitung

HOLZMANN MASCHINEN

HOLZMANN MASCHINEN TN90 Bedienungsanleitung

Metabo HPT

Metabo HPT NR 3690DC Bedienungsanleitung

Surtek

Surtek CN650 Abmessungen und Installationsanleitung

Makita

Makita GF600 Bedienungsanleitung

Parkside

Parkside PET 25 B1 Bedienungsanleitung

Senco

Senco AirFree 25 Bedienungsanleitung

Freeman

Freeman P50LSLW Bedienungsanleitung

Aicon PRO

Aicon PRO DAC4507 Bedienungsanleitung

DAJ

DAJ XR150A Bedienungsanleitung

Makita

Makita AN923 Bedienungsanleitung

Grizzly

Grizzly T20644 Bedienungsanleitung